PowMr POW-HVM5.5M Manual de usuario

Important Safety Instructions

Please save these instructions for future use!

Read all of the instructions and cautions in the manual before beginning the installation !

Purpose

This manual describes the assembly, installation, operation and troubleshooting of this unit. Please

read this manual carefully before installations and operations. Keep this manual for future

reference.

Scope

This manual provides safety and installation guidelines as well as information on tools and wiring.

Safety Instructions

WARNING: This chapter contains important safety and operating instructions. Read and

keep this manual for future reference.

⚫Before using the unit, read all instructions and cautionary markings on the unit, the batteries and

all appropriate sections of this manual.

⚫CAUTION --To reduce risk of injury, charge only deep-cycle lead acid type rechargeable

batteries. Other types of batteries may burst, causing personal injury and damage.

⚫Do not disassemble the unit. Take it to a qualified service center when service or repair is

required. Incorrect re-assembly may result in a risk of electric shock or fire.

⚫To reduce risk of electric shock, disconnect all wirings before attempting any maintenance or

cleaning. Turning off the unit will not reduce this risk.

⚫CAUTION –Only qualified personnel can install this device with battery.

⚫NEVER charge a frozen battery.

⚫For optimum operation of this inverter/charger, please follow required spec to select appropriate

cable size. It’s very important to correctly operate this inverter/charger.

⚫Be very cautious when working with metal tools on or around batteries. A potential risk exists to

drop a tool to spark or short circuit batteries or other electrical parts and could cause an

explosion.

⚫Please strictly follow installation procedure when you want to disconnect AC or DC terminals.

Please refer to INSTALLATION section of this manual for the details.

⚫Fuse is provided as over-current protection for the battery supply.

⚫GROUNDING INSTRUCTIONS -This inverter/charger should be connected to a permanent

grounded wiring system. Be sure to comply with local requirements and regulation to install this

inverter.

⚫NEVER cause AC output and DC input short circuited. Do NOT connect to the mains when DC

input short circuits.

⚫Warning!! Only qualified service persons are able to service this device. If errors still persist

after following troubleshooting table, please send this inverter/charger back to local dealer or

service center for maintenance.

2 
 
Table of Contents 
 
Important Safety Instructions....................................................................................................... 1
 Purpose.................................................................................................................................. 1
 Scope ..................................................................................................................................... 1
 Safety Instructions .................................................................................................................. 1
Introduction................................................................................................................................... 4
 Features ................................................................................................................................. 4
 Basic System Architecture ...................................................................................................... 5
 Product Overview ................................................................................................................... 6
Installation..................................................................................................................................... 7
 Unpacking and Inspection....................................................................................................... 7
 Select the mount location........................................................................................................ 7
 Mount the inverter................................................................................................................... 8
 Preparation............................................................................................................................. 8
Connection .................................................................................................................................... 9
 Battery Connection ................................................................................................................. 9
 AC Input/Output Connection ..................................................................................................11 
 PV Connection...................................................................................................................... 13 
 Final Assembly ..................................................................................................................... 15 
Operation..................................................................................................................................... 16 
 Power ON/OFF..................................................................................................................... 16 
 Operation and Display Panel ................................................................................................ 16 
 LCD Display Icons ................................................................................................................ 17 
 LCD Setting .......................................................................................................................... 19 
 LCD display description ........................................................................................................ 32 
 Operating Mode Description ................................................................................................. 37 
 Fault Reference Code........................................................................................................... 43 
 Warning Indicator.................................................................................................................. 45 
Battery Equalization.................................................................................................................... 47 
Setting For Lithium Battery ........................................................................................................ 49 
 Lithium Battery Connection................................................................................................... 49 
 Setting for PYLON US2000 lithium battery............................................................................ 50 
Table of Contents 
 

3 
 
 Setting for lithium battery without communication.................................................................. 51 
Specifications.............................................................................................................................. 53 
 Table 1 Line Mode Specifications.......................................................................................... 53 
 Table 2 Inverter Mode Specifications..................................................................................... 54 
 Table 3 Charge Mode Specifications..................................................................................... 55 
 Table 4 General Specifications.............................................................................................. 56 
Trouble Shooting ........................................................................................................................ 57 
Parallel Installation Guide .......................................................................................................... 59 
 Instruction............................................................................................................................. 59 
 Package Contents ................................................................................................................ 59 
 Mounting the Unit.................................................................................................................. 59 
 Wiring Connection ................................................................................................................ 60 
 Parallel Operation in Single phase ........................................................................................ 62 
 Support 3-phase equipment.................................................................................................. 65 
 PV Connection...................................................................................................................... 67 
 Commissioning ..................................................................................................................... 67 
 Trouble shooting ................................................................................................................... 69 
 

Introduction

This is a multi-function inverter/charger, combining functions of inverter, MPPT solar charger and

battery charger to offer uninterruptible power support with portable size. Its comprehensive LCD

display offers user-configurable and easy-accessible button operation such as battery charging

current, AC/solar charger priority, and acceptable input voltage based on different applications.

Features

⚫Pure sine wave inverter

⚫Inverter running without battery

⚫Built-in MPPT solar controller

⚫Configurable input voltage range for home appliances and personal computers via LCD setting

⚫Configurable battery charging current based on applications via LCD setting

⚫Configurable AC/Solar Charger priority via LCD setting

⚫Compatible to mains voltage or generator power

⚫Auto restart while AC is recovering

⚫Overload/ Over temperature/ short circuit protection

⚫Smart battery charger design for optimized battery performance

⚫Cold start function

⚫Self-consumption and feed-in to the grid

⚫Statistics and records of power generation

Introduction

Basic System Architecture

The following illustration shows basic application for this inverter/charger. It also includes following

devices to have a complete running system:

1.Generator or Utility.

2.PV modules (option)

Consult with your system integrator for other possible system architectures depending on your

requirements.

This inverter can power all kinds of appliances in home or office environment, including motor-type

appliances such as tube light, fan, refrigerator and air conditioner.

Figure 1 Hybrid Power System

Product Overview

NOTE: For parallel model installation and operation, please check the parallel installation guide for

the details.

1. LCD display

2. Status indicator

3. Charging indicator

4. Fault indicator

5. Function buttons

6. Power on/off switch

7. AC input

8. AC output

9. PV input

10. Battery input

11. Circuit breaker

12. RS232 communication port

13. Parallel communication port

(only for parallel model)

14. AC grid current sensor

15. RS485 communication port

16. Grounding

Installation

Unpacking and Inspection

Before installation, please inspect the unit. Be sure that nothing inside the package is damaged.

You should have received the following items inside of package:

1.The unit x 1

2.User manual x 1

Select the mount location

Consider the following points before selecting where to install:

1. Do not mount the inverter on flammable

construction materials.

2. Mount on a solid surface.

3. Install this inverter at eye level in order to allow

the LCD display to be read at all times.

4. The ambient temperature should be between 0°C

and 55°C to ensure optimal operation.

5. The recommended installation position is to be

adhered to the wall vertically.

6. Be sure to keep other objects and surfaces as

shown in the right diagram to guarantee sufficient

heat dissipation and to have enough space for removing wires.

SUITABLE FOR MOUNTING ON CONCRETE OR OTHER NON-COMBUSTIBLE

SURFACE ONLY.

Installation

Mount the inverter

Install the unit by screwing three screws. It’s recommended to use M4 or M5 screws.

Preparation

Before connecting all wirings, please take off bottom cover by removing two screws as shown

below.

Connection

Battery Connection

⚫Recommended battery cable, stripping length (L2) and tinning length(L1):

Model

Maximum

Amperage

Battery

capacity

Wire Size

Cable mm²

L1(mm)

L2(mm)

Torque

value

5KVA

137A

200AH

2AWG

2~ 3 Nm

⚫Please follow below steps to implement battery connection

1. Remove insulation sleeve 18 mm for positive and negative cables based on recommended

stripping length.

2. Connect all battery packs as units requires. It’s suggested to use recommended battery

capacity.

3. Insert battery cable flatly into battery connector of inverter and make sure the bolts are tightened

with torque of 2-3 Nm. Make sure polarity at both the battery and the inverter/charge is correctly

connected and the battery cables are tightly screwed to the battery connector.

CAUTION

⚫For safety operation and regulation compliance, it’s requested to install a separate DC over-

current protector or disconnect device between battery and inverter. It may not be requested

to have a disconnect device in some applications, however, it’s still requested to have

over-current protection installed. Please refer to typical amperage in below table as required

fuse or breaker size.

WARNING

⚫All wiring must be performed by a qualified personnel.

⚫It's very important for system safety and efficient operation to use

appropriate cable for battery connection. To reduce risk of injury,

please use the proper recommended cable, stripping length (L2)

and tinning length (L1) as shown on the right.

Stripping Length:

Connection

Tabla de contenidos

Otros manuales de Inversor de PowMr

PowMr

PowMr POW-SunSmart 8KL3 Manual de usuario

PowMr

PowMr POW-LVM5K-48V-N Manual de usuario

PowMr

PowMr SOLXPOW X2 Series Manual de usuario

PowMr

PowMr SOLXPOW X4 Series Manual de usuario

PowMr

PowMr POW-SunSmart 8KE Manual de usuario

PowMr

PowMr POW-HPM Series Manual de usuario

PowMr

PowMr SOLXPOW X1 Series Manual de usuario

PowMr

PowMr POW-LVM3K-24V-H Manual de usuario

Manuales populares de Inversor de otras marcas

Fourgroup

Fourgroup Easy Manual de usuario

Velleman

Velleman PI300M Manual de usuario

Sungrow

Sungrow SG350HX-US Manual de usuario

WilTec

WilTec 61897 Manual de usuario

SMA

SMA SUNNY BOY STORAGE 2.5 Manual de usuario

Simplicity

Simplicity LANDLORD 316 Manual de usuario

Santak

Santak SMAX 3000 Manual de usuario

ATON

ATON RA.Store-3 Manual de usuario

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Manual de usuario

Tektronix

Tektronix CFG250 Manual de usuario

Champion

Champion 200989 Manual de usuario

Vanner

Vanner 20-500 Series Manual de usuario

GE GEP Manual de usuario

Astrel Group

Astrel Group Power Reducer Guía rápida

MULTIQUIP

MULTIQUIP GDP-5H Guía

GoWISE

GoWISE PS1007 Manual de usuario

Promate

Promate PM13500D ES Manual de usuario

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Manual de usuario