PowerTech ZM9126 Manual de usuario
Instruction Manual
Canvas Blanket
Solar Panel with
Charge
Controller
ZM9126
1
Please ensure that you have read the product manual and instructions in full
before using this product. Failure to do so many result in incorrect operation
and potentially impact the performance of the product.
This product converts natural sunlight into DC electricity. It is designed to
charge a 12V battery.
CAUTION/WARNING:
INTRODUCTION:
• For optimum performance, protect the solar cell from dust, dirt, and
other debris.
• Use and store the product in a dry and ventilated location.
• Do not use in flammable or explosive areas.
• Stop use immediately if any wires become loose or electronic
components are exposed.
• Do not pick panel up directly by the solar cells.
• Use the gap between solar cells to pick up the panel.
• Do not stand or walk on the solar panel.
BOX CONTENTS:
1 x 400W Canvas Blanket Solar Panel
1 x 30A Solar Regulator
2 x Leads
2
PRODUCT SPECIFICATIONS:
Solar Panel
Solar Cell Type: Monocrystaline
Power Output: 400W
Open Circuit Voltage: 23.7V
Short Circuit Current: 18A
Working Voltage: 22.6V
Working Current: 17.6A
Output: Anderson, USB2.0, USB/QC3.0, Type-C/
PD60W, DC5521
Weight: 10.5KG
Dimensions:
Folded: 572(W) x 360(H)mm
Unfolded: 1142(W) x 1898(H)mm
Solar Charge Controller
System Voltage: 12V
Charge Current: 30A
Discharge Current: 30A
Max. Solar Current: <50V
Battery Equalisation:
Sealed: 14.4V
GEL: 14.2V
Flood: 14.6V
Float Charge: 13.7V (Default, Adjustable)
Discharge Stop: 10.7V (Default, Adjustable)
Discharge Reconnect: 12.6V (Default, Adjustable)
USB Output: 5V, 2A
Self-Consumption: <10mA
Operating Temperature: -35°C ~ 60°C
Weight: 200g
3
• Unfold the solar panel.
• Place the unfolded solar panel in a position that receives direct sunlight,
facing to the sun. Ensure that no shadows are covering the solar cells.
• Tilt the solar panel at a suitable angle. This can be the same as your local
latitude (additional support may be necessary, not supplied).
• Connect the solar panel to the solar charge controller before
connecting battery clamp lead to the solar controller.
1. Connect the battery to the solar charge controller.
2. Connect load to solar charge controller.
3. Connect solar panel to solar charge controller.
4. Reverse this order when disconnecting.
HOW TO USE:
HOW TO CHARGE A 12V BATTERY :
Note: Heavy loads should not be connected to the battery.
4
LCD DISPLAY/KEY:
Solar Panel
Charge Discharge
Load
Voltage
Current MENU
UP (+)
ON/OFF
Down (-)
5
DISPLAY/SETTINGS:
Main Display
Discharge Ampere-hour
Battery Type
Float Voltage Recovery Voltage
Absorption Voltage
Low-Voltage Protection
Low-Voltage Recovery Error Code Interface
Cut-o Voltage
Cut-o Current
Auto-identify System Voltage
Press menu to browse
dierent interface
In main interface 1,
tap the MENU button
to enter the loop
interface.
After 50 seconds
without any operation
and no errors are
displayed, the interface
will return to the
interface 1.
When there is an
error the interface
will display error code
interface 14
Browsing Interface
Set Parameter
(long press MENU for 5 seconds to set battery type)
Lead-acid battery type menu Lithium battery type menu
Charge Ampere-hour Discharge Current
Temperature Charge Current
This symbol means that the interface can be set
This symbol means that the interface cannot be set
Work Mode
(long press MENU for 5 seconds to set the load mode)
6
TROUBLESHOOTING:
Error Code Cause Solution
E01 Low battery voltage,
load o
Change the battery or change a
new battery.
E02 Overload, load o
Decrease the load, the use (-)
button to turn on the load.
Load will automatically turn on
after 2 minutes.
E03 Load short-circuit, load o Remove the short-circuit load, use
(-) button to turn on the load.
E04 Over-voltage of battery,
load o
Check the connection of battery,
and whether if the capacity of
battery is too low, check if there is
another charger connected to the
battery.
E05 Solar panel over current,
controller stops charging
Check whether the power of solar
panel has been over powered,
decrease the panels and then
the controller will start charging
automatically after 2 minutes.
7
FULL TECHNICAL PARAMETERS:
Solar Input
Rated Current 30A
Input Voltage ≤50V
(12V)
Charge Management
Lead-acid
Batteries
3-stage charging (bulk charge, absorption charge, float charge)
Lead-acid
Batteries Sealed GEL Flood USE1
Float Voltage 13.8V 13.8V 13.8V 13.8V (9~15V adjustable)
Absorption
Voltage 14.4V 14.0V 14.6V 14.4V (9~15V adjustable)
Absorption Time 2 hours
Absorption
Recovery Voltage 12.6V
Limited Charge
Voltage 15.5V
Temperature
Compensation -4mV/cell/°C
Lithium
Batteries
3-stage charging (bulk charge, constant-voltage, stop charge)
Lithium Batteries 3.7-3 3.7-4 3.2-4 3.2-5 USE2
Constant Voltage 12.6V 16.8V 14.4V 18.0V 14.4V
(9~17V adjustable)
Cut-o Charge
Current 2A (0.1A~30A adjustable)
Recovery Charge
Voltage 12.0V 16.0V 13.6V 17.0V 13.6V
(9~17V adjustable)
Note: Parameters apply to 12V system as an example. If 24V/36V/48V system, the voltage
parameters should be *2/*3/*4
Note: 10A/20A controller without temperature compensation/backlight function, without
cut-o current.
B01 B02 B03 B04 B00
Sealed battery Gel Battery Flood Battery Lithium Battery -
Custom Type
Lead-acid Battery -
Custom Type
8
FULL TECHNICAL PARAMETERS:
Discharge Management
Batteries Type Lead-acid
Batteries
Lithium Battery
3.7-3 3.7-4 3.2-4 3.2-5 USE1
Low-Voltage
Protection
10.7V
(9~15V adjustable) 9.9V 13.2V 11.2V 14.0V 11.2V
(9~17V adjustable)
Low-Voltage
Recovery
12.6V
(9~15V adjustable) 11.1V 14.8V 12.8V 16.0V 12.8V
(9~17V adjustable)
Over-Voltage
Protection 16.0V 18.5V
Over-Voltage
Recovery 15.5V 18.0V
USB Power 5V USB, Max output 2A
Voltage Range of Battery
System Voltage Lead-acid
Batteries
Lithium Battery
3.7-3 3.7-4 3.2-4 3.2-5 USE2
12V ≤17V ≤14.6V ≤18.8V ≤16.4V ≤20V ≤16.4V
Other Specifications
Max Wire Size 6mm2(AWG #9) / 16mm2(AWG#5) / 25mm2(AWG #3)
Working Temperature -20°C ~ 50°C
Storage Temperature -30°C ~ 70°C
Working Humidity 10% ~ 90%, no condensation
Dimensions 187 x 98 x 50mm
Weight 370g
Waterproof IP30
9
FACTORY DEFAULT SETTINGS:
VARIOUS WORKING MODES FOR LOAD:
At main loop interface 2, press & hold the MENU button until the symbols in
the dotted column starts flashing, the controlling parameters will reset to the
default value. Controller will restart automatically to re-new the controller data.
There are four control modes for the load. (1) Normal control mode, (2)
Light control on, (3) Delayed o mode, (4) Reverse light control mode. The
delayed duration can be between 1-24 hours.
Following are the working introduction for each mode:
Load Mode
Event
Dark Setting Time Dawn
24H normal control mode - - -
1-23H light control on and
delayed off mode Load on Load o Load o
0H light control mode Load on - Load o
CH reverse light control mode Load o - Load on
Tabla de contenidos
Otros manuales de Controladores de PowerTech
PowerTech
PowerTech LL00213 Manual de usuario
PowerTech
PowerTech MP3749 Manual de usuario
PowerTech
PowerTech MP-3735 Manual de usuario
PowerTech
PowerTech MP3743 Manual de usuario
PowerTech
PowerTech MP3743 Manual de usuario
PowerTech
PowerTech MP-3760 Manual de usuario
PowerTech
PowerTech MP3755 Manual de usuario
PowerTech
PowerTech MP3741 Manual de usuario
PowerTech
PowerTech MP3768 Manual de usuario
PowerTech
PowerTech MP3764 Manual de usuario
