Powerfix Profi DIY VICE Manual de usuario
IAN 273581
dIy vICe
dIy vICe
Operation and Safety Notes
UNIveRSAL-SKRUeSTIK
Betjenings- og sikkerhetshenvisninger
UNIveRSAL-SCHRAUBSTOCK
Bedienungs- und Sicherheitshinweise
ÉTAU
Instructions d‘utilisation et consignes de sécurité
UNIveRSeLe BANKSCHROef
Bedienings- en veiligheidsinstructies
GB/IE Operation and Safety Notes Page 5
DK Betjenings- og sikkerhetshenvisninger Side 10
FR/BE Instructions d‘utilisation et consignes de sécurité Page 15
NL/BE Bedienings- en veiligheidsinstructies Pagina 20
DE/AT/CH Bedienungs- und Sicherheitshinweise Seite 15
8
9
10
11
13
1
2
3
5
4
6
7
12
5GB/IE
Introduction
Intended Use .................................................................... Page 6
Description of parts and features.................................... Page 6
Technical data.................................................................. Page 7
Included items .................................................................. Page 7
Safety advice............................................................ Page 7
Fixing in place.......................................................... Page 8
Use
Clamping and releasing a workpiece ............................ Page 8
Mounting the tube attachment ........................................ Page 9
Cleaning and care................................................. Page 9
Disposal......................................................................... Page 9
6 GB/IE
DIY VICE
Introduction
The instructions for use are to be considered as part of the
product. They contain important information concerning
safety, use and disposal. Before using the product,
please familiarise yourself with all of the safety information and
instructions for use. The product must only be used as described
and for the stated fields of application. If you pass the product on
to third parties, please give them all of the documentation as well.
Intended Use
The product is intended for clamping small, light workpieces made
of wood or metal, e.g. for model-making, to hold them still while
further work is performed on them. Other uses or changes to the
product are considered to be contrary to the intended use and
may harbour risks of injury and damage. The manufacturer does
not accept any liability for injury or damage resulting from use of
this product contrary to its intended use. The product is not intended
to be used for commercial purposes.
Description of parts and features
1Jaw protectors
2Jaws with V-grooves
3Hexagonal socket head screw
4Hexagonal socket head screw
5Ball joint
6Ball joint tommy bar
7Clamping screw
8Hexagonal socket head screw
9Vice jaws tommy bar
10 Spindle
11 Vice base
7GB/IE
12 Hexagon socket screw key
13 Tube attachment
Technical data
Maximum jaw opening width: approx. 50mm
Length of jaws: approx. 78mm
Maximum bench top thickness: approx. 50mm
Weight: approx. 865g
Dimensions height: approx. 14.6 x 7.8 x 26cm
(l x w x h)
Height from top of bench: approx. 15.5cm
Tube attachment: ø approx. 38-43mm
Max. tube weight: 2kg
Max. tube length: 30cm
Included items
1 Diy vice
1 Hexagon socket screw key
1 Tube attachment
1 Operating instructions
Safety advice
KEEP ALL THE SAFETY ADVICE AND INSTRUCTIONS IN A
SAFE PLACE FOR FUTURE REFERENCE.
CAUTION! DANGER OF INJURY! When working with
hand-held electrical power tools, you can be seriously injured
if the clamped workpiece slips or becomes loose. Never work
on a clamped workpiece using hand-held electrical power tools.
Check the product before each use for any damage. Do not
use the product if you discover it is damaged in any way.
Check all threaded connections on the product for proper
seating before each use.
8 GB/IE
Use the product on a stable, flat, undamaged surface (e.g.
a workbench).
Place circular workpieces in the vertical or horizontal V-groove
and clamp them tightly in place. By doing this you will prevent
the workpiece from slipping.
The vice is an aluminium injection casting and therefore is only
impact resistant to limited extent.
Do not use extension tubes on the tommy bars. There is the
danger of overloading (fracturing) the spindle.
Wear safety gloves and glasses.
Fixing in place
Attach the vice on to a smooth, flat surface.
To do this turn the clamping screw 7anticlockwise until the
clamp opening has widened enough.
Push the vice on the supporting surface (table-top,
workbench) and fix it in place on the supporting surface by
turning the clamping screw 7.
Use
Clamping and releasing a workpiece
1. Turn the vice base 11 into the desired position and fix the ball
joint 5in position with the ball joint tommy bar 6.
Note: Turn the vice base 11 so that the ends of the jaws 2
project out over the supporting surface. This allows you to
clamp even long workpieces (in the limiting case with one end
on the floor) to work on their ends.
2. Turn the vice jaws tommy bar 9anticlockwise to open the
jaws 2.
3. Place the workpiece between the jaws 2and clamp it by
turning the vice jaws tommy bar 9clockwise. Ensure that the
workpiece is tightly clamped.
You can now work on the workpiece.
After completing work on the workpiece, release it by turning
the vice jaws tommy bar 9anticlockwise.
9GB/IE
Mounting the tube attachment
The tube attachment is intended for clamping tubes with a diameter
of 38- 43mm.
1. Release the hexagonal socket head screw 3at the end of
the spindle using the supplied hexagon socket screw key 12 .
2. Turn the vice jaws tommy bar 9anticlockwise until the
spindle 10 is turned out of the rear jaw 2.
3. Using the supplied hexagon socket screw key 12 , release the
hexagonal socket head screw 8on the underside of the vice
base 11 and remove the spindle 10 from the vice.
4. Now that the hexagonal socket head screw 4is accessible,
remove it and take the vice base off the ball joint 5.
5. Place the tube attachment 13 on to the ball joint 5and
fasten it in place with the hexagonal socket head screw 4.
6. Turn and tilt the ball joint 5to achieve the right position.
Cleaning and care
Clean the product with a dry, fluff-free cloth.
Never use aggressive or corrosive cleaning agents, as they
may damage the product.
Disposal
The packaging is made entirely of recyclable materials,
which you may dispose of at local recycling facilities.
Contact your local refuse disposal authority fo r more details of
how to dispose of your worn-out product.
10 DK
Indledning
Formålsbestemt anvendelse............................................. Side 11
Beskrivelse af delene ....................................................... Side 11
Tekniske Data ................................................................... Side 12
Leveringsomfang .............................................................. Side 12
Sikkerhedshenvisninger ................................. Side 12
Montering.................................................................... Side 13
Anvendelse
Et værkstykke spændes fast/løsnes ............................... Side 13
Rørholder monteres.......................................................... Side 14
Rensning og pleje.................................................. Side 14
Bortskaffelse............................................................. Side 14
11DK
UNIVERSAL-SKRUESTIK
Indledning
Brugsvejledningen er del af dette produkt Den indeholder
vigtige informationer om sikkerhed, brug og bortkastning.
Gør diginden ibrugtagning af produktet fortrolig med
alle betjenings- og sikkerhedsinformationer. Brug kun produktet
som beskrevet og kun til de dertil oplyste formål. Videregiv alle
papirer, hvis du giver apparatet videre til tredjemand.
Formålsbestemt anvendelse
Produktet er beregnet til indspænding af små lette værkstykker
af træ eller metal, f. eks. indenfor modelbygning, til efterfølgende
bearbejdelse. Anden anvendelse eller ændringer på produktet
gælder som ikke formålsbestemte og kan medføre fare for person-
skader eller andre skader. Producenten hæfter ikke for skader, der
er opstået ved anvendelse i strid med produktets bestemmelse.
Produktet må ikke anvendes til erhvervsmæssige formål.
Beskrivelse af delene
1Beskyttelseshætter til spændebakker
2Spændebakker med V-nut
3Unbrakoskrue
4Unbrakoskrue
5Kugleled
6Fastgørelsesspændepind til kugleleddet
7Klemskrue
8Unbrakoskrue
9Fastgørelsesspændepind til spændebakkerne
10 Spindel
11 Skruestikopsats
12 Unbrakonøgle
13 Rørholder
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Idiomas:
Otros manuales de Herramientas de Powerfix Profi
Powerfix Profi
Powerfix Profi 284621 Manual de usuario
Powerfix Profi
Powerfix Profi 283350 Manual de usuario
Powerfix Profi
Powerfix Profi PFRS 1.5 A1 Manual de usuario
Powerfix Profi
Powerfix Profi PLPRS A1 Manual de usuario
Powerfix Profi
Powerfix Profi 282485 Manual de usuario
Powerfix Profi
Powerfix Profi PKRS 1.5 A1 Manual de usuario
Powerfix Profi
Powerfix Profi 312154 Manual de usuario
Powerfix Profi
Powerfix Profi PMTR 4 A1 Manual del propietario
Powerfix Profi
Powerfix Profi 314158 Manual de usuario
Powerfix Profi
Powerfix Profi PFRS 1.5 A1 Manual de usuario
Powerfix Profi
Powerfix Profi Z30003 Manual de usuario
Powerfix Profi
Powerfix Profi HG01976 Manual de usuario
Powerfix Profi
Powerfix Profi PMTR 4 A1 Guía de inicio rápido
Powerfix Profi
Powerfix Profi 71825 Manual del propietario
Powerfix Profi
Powerfix Profi Z29760A Manual de usuario
Powerfix Profi
Powerfix Profi PLPRS A1 Manual de usuario
Powerfix Profi
Powerfix Profi 114378 Manual de usuario
Powerfix Profi
Powerfix Profi PMTR 4 A1 Manual del propietario
Powerfix Profi
Powerfix Profi PLPRS A1 Manual de usuario
Powerfix Profi
Powerfix Profi PMTR 4 A1 Manual del propietario
