Power Craft PSC-360 Manual técnico
3.6V LITHIUM-ION
SCREWDRIVER AND KIT
User Guide & Warranty
After Sales Support
Now you have purchased a Power Craft
product you can rest assured in the
knowledge that as well as your 3 year
parts and labour warranty you have
the added peace of mind of dedicated
helplines and web support.
AFTER SALES SUPPORT
UK HELPLINE NO 0905-1460005 (£ 0,06 /min.)
IRELAND HELPLINE NO 1520-932626 (E 0,15 /min.)
WEB SUPPORT www.heltec.eu
Model nuMber: PSC-360/2lK
CDM6100 Ma-GB-IRE # 0808-15.indd 1 15-08-2008 09:51:04
Contents
03 Introduction
05 Machine specifications
07 Safety instructions
- General safety instructions
- Additional safety instructions
11 Assembly
- Inserting and removing bits
12 Operation
- Locking the screwdriver
- Screwdriving
- User tips for optimum use
- Charging the Lithium-Ion battery
15 Maintenance
19 Warranty
UK Helpline 0905-1460005 • Ireland Helpline 1520-932626
Web Support: www.heltec.eu
Model Number: PSC-360/2LK
2
CDM6100 Ma-GB-IRE # 0808-15.indd 2 15-08-2008 09:51:04
Introduction
Congratulations on choosing to buy a Power
Craft product.
By doing so you now have the assurance and peace of mind that comes with
purchasing a product made by one of Europe’s leading manufacturers.
All products brought to you by Power Craft are manufactured to the highest
standards of performances and safety, and, as part of our philosophy for
customer service and satisfaction, are backed by our comprehensive
3 Year Warranty.
We hope you will enjoy using your purchase for many years to come.
3.6V Lithium-Ion screwdriver
Always read the instructions for electrical products carefully before
use. It will help you understand your product better and avoid
unnecessary risks. Keep this instructions manual in a safe place for
future use.
This screwdriver is intended for tightening and loosening screws (fig. 1-5).
The screwdriver is not suitable for screwdriving heavy constructions, e.g.
repairing a large fence.
Fig. 1 Fig.2
UK Helpline 0905-1460005 • Ireland Helpline 1520-932626
Web Support: www.heltec.eu
Model Number: PSC-360/2LK
3
CDM6100 Ma-GB-IRE # 0808-15.indd 3 15-08-2008 09:51:05
Introduction
Fig. 3 Fig.4
Fig. 5
UK Helpline 0905-1460005 • Ireland Helpline 1520-932626
Web Support: www.heltec.eu
Model Number: PSC-360/2LK
4
CDM6100 Ma-GB-IRE # 0808-15.indd 4 15-08-2008 09:51:05
Machine specifications
Technical specifications
Charger 3.6 V/600 mA
Frequency 50 Hz
Voltage 230 V
Battery capacity 1.1 Ah
Charging time 3-5 hours
Max torque 3.0 Nm
No-load speed 230/min
Weight 340 gr
Sound pressure level (Lpa) 60.5 dB(A)
Sound power level (Lwa) 71.5 dB(A)
Vibration 4 m/s2
Product information
Fig.6
UK Helpline 0905-1460005 • Ireland Helpline 1520-932626
Web Support: www.heltec.eu
Model Number: PSC-360/2LK
5
5
32
7
4
1
6
8
9
10
CDM6100 Ma-GB-IRE # 0808-15.indd 5 15-08-2008 09:51:06
Machine specifications
Bit holder1.
LED worklights (white)2.
On/Off switch3.
Softgrip4.
LED (red)5.
Charger connection6.
Right/Left rotation switch7.
Bits8.
Extension piece9.
Charger10.
Package contents
1 Cordless screwdriver
1 Charger
1 Extension piece
26 Accessories
1 Instruction manual
1 Warranty card
UK Helpline 0905-1460005 • Ireland Helpline 1520-932626
Web Support: www.heltec.eu
Model Number: PSC-360/2LK
6
CDM6100 Ma-GB-IRE # 0808-15.indd 6 15-08-2008 09:51:06
Safety instructions
The following symbols are used in these instructions:
Read the instructions carefully.
Conformity with the relevant EU safety directives.
Class II machine- double insulation- earth connection not required.
Danger of life and risk of injury as well as risk of damage to the
machine in case of non-adherence to the safety instructions in
these instructions of use.
Danger of electric shock.
Device can rotate in both directions.
Indoor use only
In case of failure, the transformer is not dangerous.
Thermic protector.
Faulty and/or discarded electrical or electronic machines have to
be collected at the appropriate recycling locations.
Do not use in damp and wet conditions.
UK Helpline 0905-1460005 • Ireland Helpline 1520-932626
Web Support: www.heltec.eu
Model Number: PSC-360/2LK
7
CDM6100 Ma-GB-IRE # 0808-15.indd 7 15-08-2008 09:51:10
Safety instructions
General Safety Instructions
Caution! Read all instructions. The non-observation of the instructions
mentioned below may cause an electric shock, fire and/or severe injuries. The
term “electric tool” mentioned below refers to mains-operated electric tools
(with a power cord) and to rechargeable electric tools (without power cord).
Keep these instructions for use in a safe place.
1) Workplace
(a) Keep your workplace clean and tidy. Untidy and badly illuminated work
areas may lead to accidents.
(b) Do not operate this machine in potentially explosive environments
containing combustible liquids, gases or dusts. Electric tools send out
sparks which may ignite dust or vapours.
(c) Keep children and other persons away from the electric tool during use.
When distracted, you may lose control over the apparatus.
2) Electric safety
(a) The plug of the machine has to be suitable for the socket. The connector
may not be modified in any way. Do not use an adapter plug together
with earthed devices. Unchanged connectors and fitting sockets reduce
the risk of an electric shock.
(b) Avoid body contact to earthed surfaces, such as pipes, radiators, stoves and
refrigerators. There is a higher risk of an electric shock, if your body is
earthed.
(c) Keep the machine clear of rain or humidity. The penetration of water into
an electrical device increases the risk of an electric shock.
(d) Do not use the cable for unintended purposes, to carry or suspend the
machine or to pull the connector out of the socket. Keep the cable clear
of heat, oil, sharp edges or any moving parts. Damaged or entangled
cables increase the risk of an electric shock.
(e) When using an electric tool in the open, use an extension cable only
which has been approved for outdoor use. The use of an extension cable
suitable for use in the open will reduce the risk of an electric shock.
Always use an RCD (redicual circuit device or circuit breaker).
3) Personal safety
(a) Please pay attention and watch what you are doing, and carry out the
work with the electric tool sensibly. Do not use the machine, when you are
tired or under the influence of drugs, alcohol or medicine. A moment of
carelessness in the use of the machine could lead to serious injuries.
UK Helpline 0905-1460005 • Ireland Helpline 1520-932626
Web Support: www.heltec.eu
Model Number: PSC-360/2LK
8
CDM6100 Ma-GB-IRE # 0808-15.indd 8 15-08-2008 09:51:10
Safety instructions
(b) Wear your safety equipment and always put on safety goggles. Wearing
personal protective gear, such as a dust mask, anti-skid safety shoes, hard
hat and ear protection, depending on the use of the electric tool, will
reduce the risk of injury.
(c) Avoid unintentional operation. Make sure that the switch is in the “OFF”
position before you remove the plug from the socket. If you have your
finger on the switch when carrying the machine or if you connect the
running machine to the socket, this may lead to accidents.
(d) Remove the adjusting tools or the spanners before switching on the
machine. A tool or a key which is located in a revolving part of the
machine may lead to injuries.
(e) Concentrate and keep your balance at all times as you will be able to
control the machine better in unexpected situations.
(f) Wear suitable clothing. Do not wear any loose clothing or jewellery. Keep
your hair, clothing and gloves clear of any moving parts.
(g) If dust extraction or collection devices can be mounted, make sure that
they are connected properly and are used in the proper way. The use of
these pieces of equipment reduce hazards caused by dust.
4) Careful handling and use of electric tools
(a) Use the correct tool for the job at hand.
(b) Do not use an electric tool, if the switch is defective. An electric tool,
which cannot be switched on or off, is dangerous and has to be repaired.
(c) Remove the plug from the socket before setting down the machine,
changing accessories or putting the machine aside. This precautionary
measure prevents the unintentional start of the machine.
(d) Keep unused electric tools out of reach of children. Do not permit persons
to use the machine who are not familiar with it or who have not read
these instructions. Electric tools are dangerous, if they are used by an
inexperienced person.
(e) Maintain the machine with care. Please check whether the movable parts
are perfectly operational and do not jam, whether parts have broken or
have been damaged in such a way that the function of the machine is
impaired. Have damaged parts repaired prior to using the machine. Many
accidents are caused by electric tools which are poorly maintained.
(f) Keep all cutting tools sharp and clean.
(g)Use the electric tool, the accessories, the insert tools, etc according to these
instructions, and in the way described for this special type of apparatus. In
the process, take the working conditions and the work to be carried out into
consideration. Only use this tool for the purpose for which it is intended.
UK Helpline 0905-1460005 • Ireland Helpline 1520-932626
Web Support: www.heltec.eu
Model Number: PSC-360/2LK
9
CDM6100 Ma-GB-IRE # 0808-15.indd 9 15-08-2008 09:51:11
Safety instructions
(h) Use clamps or vice to hold work. It is safer then using your hands and
frees both hands to operate the tool.
5) Servicing
(a) Have your machine repaired by qualified expert staff using original spare
parts only.
(b) Caution! The use of accessories or add-on devices other than those
recommended in these instructions may mean a risk of injury. Use original
spare parts only.
Additional Safety Instructions
1. Only use the accumulator block with the battery charger provided – using
other chargers could be dangerous.
2. Keep the accumulator block, tool and battery charger away from damp
and wet conditions.
3. Before using the battery charger, check all wires are properly connected.
4. If any wires on the charger are damaged, do not use it until these have
been replaced.
5. When the charger is not in use it should not be plugged in. When
unplugging, do not pull the plug out by the cable.
6. If the charger breaks down or suffers from other technical problems, take
it to a recognised dealership to be checked before using it again. Any
damaged parts must be replaced.
7. Take care when handling the accumulator block, do not drop it or knock
it against other things.
8. Never attempt to repair the battery charger or accumulator block yourself
as this can be extremely dangerous. Repairs should always be carried out
by a recognised dealership.
9. Always unplug the charger before cleaning or carrying out any other
maintenance on it.
10. Do not attempt to charge the accumulator block in temperatures of
below 5 °C or above 40 °C.
11. Never throw the accumulator block into water or a fire – it may explode.
12. Turn the screwdriver immediately off after the screw is fastened.
Overloading and damaging the battery or motor can be prevented this
way. Use the torque to loosen the fastened screw.
UK Helpline 0905-1460005 • Ireland Helpline 1520-932626
Web Support: www.heltec.eu
Model Number: PSC-360/2LK
10
CDM6100 Ma-GB-IRE # 0808-15.indd 10 15-08-2008 09:51:11
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Destornillador eléctrico de Power Craft
Power Craft
Power Craft 69290 Manual de usuario
Power Craft
Power Craft ECD 16 Manual de usuario
Power Craft
Power Craft SD36ZG-11 Manual de usuario
Power Craft
Power Craft PCS4.8V Manual técnico
Power Craft
Power Craft 10653 Manual de usuario
Power Craft
Power Craft 10616 Manual de usuario
Power Craft
Power Craft 26182 Manual de usuario
Power Craft
Power Craft 10607 Manual de usuario
Power Craft
Power Craft PSD-480K Manual de usuario
