POSEIDON 2305 Guía de configuración
CYKLON
1.0:E59
FIRST STAGE VALVE
2305, 2422, 3070
Secondary side:
Removal:
Place the first-stage valve in fixture
with the secondary side facing
upwards.
1. Remove the pressure adjusting
screw (1) with a 6 mm hexagon
spanner, and remove the spring
(2) and (3).
2. Remove the cover (4) using a 27
mm crowsfoot wrench. Remove
the upper diaphragm center (5).
3. Remove the diaphragm (6) with
an o-ring remover. Make sure
the sealing surface is not
damaged. Remove the lower
diaphragm center (7) and the
valve needle (8).
CYKLON
1.0:E60
FIRST STAGE
3070 (2422)
1. Remove the locking screw (23) with a 6
mm Allen wrench. 20 Remove the o-
ring (24), cup filter (21) and o-ring (22).
2. Place the first stage in the fixture.
Remove the connection (20) with 6 mm
Allen wrench.
3. Remove the wheel (18) and the o-ring
(19) with an o-ring remover. Make sure
the sealing surfaces are not damaged.
4. Remove the spring (17) and the valve
piston (16).
5. Disconnect the low pressure hose from
the first-stage valve with a 13 mm
open-end wrench.
6. Remove the o-ring from the low
pressure hose. Make sure the sealing
surfaces are not damaged.
FIRST STAGE
2305
1. Remove the o-ring (20) with an o-ring
remover. Make sure the sealing surfaces
are not damaged.
2. Remove the locking screw (19) with a
8.5 mm screwdriver. Remove the cup
type filter (18).
3. Place the first stage housing in the
fixture. Remove the connection (17)
using a 6 mm Allen wrench.
4. Remove the o-ring (15) with an o-
remover. Make sure the sealing surfaces
are not damaged.
5. Remove the wheel (16).
6. Remove the spring (14) and the valve
piston (13).
7. Disconnect the low pressure hose
from the first stage valve with a 13
mm openend wrench.
8. Remove the o-ring from the low
pressure hose. Make sure the sealing
surfaces are not damaged.
CYKLON
1.0:E61
1. Remove the valve seat (15) with
the valve seat remover.
2. Remove the o-ring (14) with an
o-ring remover. Make sure that
the sealing surfaces are not
damaged.
3. Remove the blind screws (9)
and (13) with a 5 mm Allen
wrench. Remove the o-rings
with an o-ring remover. Make
sure that the sealing surfaces
are not damaged.
Old-type fist stage valve housings
with (G 1/8”) threads are equipped
with nylon gaskets seats.
It is not normally necessary to
change these seats during service.
However, if the seats are subjected
to a great deal of over-tightening,
the interior orfices can be reduced
in diameter, significantly reducing
flow and performance. Compare
installed gasket orifices with a new
gasket, and replace as necessary.
Gaskets must also be replaced
after a long time acid-bath.
Sealing surfaces
a. G1/8’’-port with gasket.
b. UNF 3/8’’-port with o-ring
CYKLON
1.0:E62
When servicing the regulator following
parts should be replaced:
See chapter Servicekit.
1. All o-rings
2. Diaphragm
3. Cup filter
4. Valve seat
Cleaning:
If corrosion or salt deposits are in
evidence, place all metal parts in 15
percent hydro-chloric acid.They should be
left in the acid for about 10-15 minutes.
Then, rinse the parts thoroughly and blow
dry with air.
SERVICE INSTRUCTIONS
Checking:
Check the following parts very carefully.
Replace even if only slightly damaged.
Valve needle (8). Check to make sure that
the needle is straight.
The blind screws (9) and (13), check to
make sure the sealing surfaces are
undamaged. Also check that the threads
are not damaged.
The valve housing (11), check to make
sure the threads and also the sealing
surfaces for the o-rings are undamaged.
The connections (17) or (20), check to
make sure the sealing surfaces for the
o-rings are undamaged.
CYKLON
1.0:E63
Assembly
Lubricant:
Grease:
1. Install the o-ring (10) on the blind
screws (9), low pressure supply and the
o-ring (12) on the blind screw (13), high
pressure supply. Lubricate the blind
screws and the o-rings.
2. Screw in the blind screws in the
LP-HP outlets. Use a 5 mm Allen
wrench an tighten hard.
3. Install the o-ring (14) on the valve
seat (15) and then install the valve
seat with a seat drift.
4. Lubricate the point of the valve needle
(8) and install it in the lower diaphragm
center (7). (The grease will help retain
the needle on the lower diaphragm
center during the assembly process).
5. Install needle (8) and center (7) in
the valve housing.
6. Press the diaphragm (6) into the
groove of the valve housing. Use a
blunt-pointed instrument to set it
firmly in place.
NOTE:
The diaphragm (6) must be replaced on
every removal.
7. Reverse the valve housing.
8. Install the valve piston (16) on the
valve needle.
9. Install the spring (17) on the valve
piston.
CYKLON
1.0:E64
FIRST STAGE
3070, 2422
1. Install the o-ring (19) on the
connection housing (20). Lubricate
the o-ring and the thread
2. Install the wheel (18) on the con
nection (20).
3. Screw the wheel connection
assembly into the valve housing
assembly with a 6 mm Allen
wrench. Reverse the valve
housing. Check the movement of
the valve piston by pressing hard
on the diaphragm. The movement
should be about 1.5 mm (1/16”).
FIRST STAGE
2305
1. Install the wheel (16) on the
connection (17). Install the o-ring
(15) on the connection (17).
Lubricate the o-ring and the
thread
2. Screw the wheel connection
assembly into the valve housing
assembly with a 6 mm Allen
wrench. Reverse the valve
housing. Check the movement of
the valve piston by pressing hard
on the diaphragm. The movement
should be about 1.5 mm (1/16”).
CYKLON
1.0:E65
1. Place the upper diaphragm
center (5) on the diaphragm in
the valve housing.
2. Screw the cover (4) into the
valve housing.
3. Lubricate both ends of the
spring (2) and (3). Lubricate the
threads on the pressure
adjusting screw(1).
4. Tighten the pressure adjusting
screw about 5 turns with a 6
mm Allen wrench.
Place the stage assembly in the
fixture. Tighten the valve housing
cover with a 27 mm crowsfoot and
the connection with a 6 mm Allen
wrench. use a torque wrench to
achieve 28-30 Nrn (20-22 Ibf.ft) of
torsion.
IMPORTANT NOTE: Use the right
bits: To all first stages with wheel
connection, bits No. 3119 (length
40 mm) should be used.
CYKLON
1.0:E66
FIRST STAGE
3070, 2422
1. Install the o-ring (22) on the cup
type 21), then install the locking
screw and o-ring (23). Tighten
with a 6 mm Allen wrench.
FIRST STAGE
2305
1. Install the cup filter (18) and
the locking screw (19) with a
8.5 mm screwdriver.
Install the o-ring (20).
2. Install the o-ring (9) on the LP
hose. Lubricate the o-ring and
the thread.Tighten the hose
nipple with a 13 mm openend
wrench.
INSTALLMENT OF ANTIFREEZE CAP
1. Check valve cover for correct tightness - 28-30 Nm.(20-22 lbf.ft)
2. Blow the inside of the valve cover clean and dry.
3. Then fill the valve cover and the rubber with pure
spirit (alcohol, vodka) or water/glycol mixture. 3/4 fill.
4. Install the anti-freeze cap and fasten it with the locking band.
CYKLON
1.0:E67
OLD TYPE
For assembly of old-type spring
housing, please note the following:
1. The upper diaphragm centre
must be centered in the mid
part.
2. The inner and outer secondary
springs shall be set in the
middle.
3. Screw carefully on the cover
with assembly screw.
4. Tighten the valve housing cover
with a special tool No. 2318. Use
a torque wrench to achieve 28
Nm (20 Ibf.ft).
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Instrumento de buceo de POSEIDON
POSEIDON
POSEIDON MKVI Manual de usuario
POSEIDON
POSEIDON 3755 Guía de configuración
POSEIDON
POSEIDON 3720 Guía de configuración
POSEIDON
POSEIDON PEEDB9393 Manual de usuario
POSEIDON
POSEIDON MKVI Manual de usuario
POSEIDON
POSEIDON PVH2365 Manual de usuario
POSEIDON
POSEIDON EBS MkII Manual de usuario
POSEIDON
POSEIDON Jetstream Guía de configuración
POSEIDON
POSEIDON 2710 Guía de configuración
POSEIDON
POSEIDON XSTREAM Manual de usuario
POSEIDON
POSEIDON M28 Manual de usuario
POSEIDON
POSEIDON 0336 - 164 Manual de usuario
POSEIDON
POSEIDON Xstream Series Manual de usuario
POSEIDON
POSEIDON 3790 Guía de configuración
POSEIDON
POSEIDON Pegasus Deluxe Manual
POSEIDON
POSEIDON 2801 Guía de configuración
POSEIDON
POSEIDON 3880 Guía de configuración
POSEIDON
POSEIDON Besea Series Manual de usuario
POSEIDON
POSEIDON Xstream Series Manual de usuario
POSEIDON
POSEIDON Rebreather Wing Manual de usuario
