POSEIDON 1133 Guía de configuración
CYKLON
1.0:E49
SECOND STAGE
1133, 3224, 3354, 3536
Removal:
1. Disconnect the low pressure
hose from the second stage
with a 17 mm. open wrench.
Remove the oring (2) with an
o-rings remover.
2. Remove the diaphragm housing
(27) from the mouth piece tube.
3. To release the exhalation cover,
remove the locking ring with a
small screwdriver.
4. Remove the exhalation
diaphragm (21).
CYKLON
1.0:E50
1. Remove the locking ring (25)
with an awl. Support the
diaphragm house, see diagram.
Make sure that the sealing
surface for the exhalation
diaphragm is not damaged.
2. Remove the cover (24) and the
inhalation diaphragm (23).
Removal: Push out the purge
button
IMPORTANT! The purge button
(26) should not be removed if it
is undamaged
3. Remove the connecting ring (4)
and the low pressure valve (15).
CYKLON
1.0:E51
1. Cut off the locking strap (17)
with cutting pliers.
2. Remove the mouth-piece (16)
and the o-ring (12).
1. Remove the lever pin (11).
2. Remove the operating device
(14).
3. Remove the o-ring (12).
4. Unserew the valve seat (5) with
an 8.5 mm screwdriver. NOTE!
the valve seat has a very fragile
tightening edge; put the seat
with the edge upwards.
5. Remove the valve piston (8) and
the spring (9). In order to
protect the piston bond, the old
rubber plate should be kept
until the new shall be fixed.
6. Remove the o-ring (6) with an
oring remover. Make sure the
sealing surfaces ar not
damaged.
IMPORTANT! The ejector sleeve
should not be removed if it is
functional and undamaged.
Check to see that the sleeve can
be rotated to any position, but
that it does not rotate freely.
CYKLON
1.0:E52
When servicing the regulator the
following parts should be replaced:
See chapter Servicekit.
1. All o-rings, including the one in
the low-pressure hose.
2. Rubber plate (7).
CLEANING:
If corrosion or salt deposits occurs, place all metal
parts – concentrated Hempocid* or 15% Hydrochloric
acid for about 10 minutes.Then, rince the parts
thoroughly and blow dry with air. The synthetic parts
in the second stage must not be treated with solvent.
They shall be cleaned in freshwater only.
*Hempocid = Acid Liquid Detergent Containing
phosphoric acid (5 - 10%) and bactericid for
desinfectant cleaning.
BEFORE INSTALLING CHECK THE
FOLLOWING:
1. Diaphragms (21) (23). Check the sealing surface of
the diaphragm to see if it is even and uncracked.
2. The mouth-piece (16).
Make sure that there are no cracks.
3. The purge button (26).
Make sure there are no cracks.
4. Valve piston (8). Ensure that the ball joint is
working correctly by manipulating and rotating
the joint.
5. Operating device (14). Make sure that the joint
articulates smoothly. Important:The operating
device must be replaced, if the lever tab is bent.
The tab should not be straightened, as this would
weaken it and make subsequent failure possible.
6. Valve seat (5). Check to make sure the sealing
surfaces are undamaged.
7. Low pressure hose (3). Check to make sure that the
sealing surface is undamaged, and that the rubber
does not show any flaws.
8. Diaphragm housing (22). Make sure that the
sealing surfaces are free from defeas and that the
track for the inhalation diaphragm is absolutely
clean and free from lubricant.
CYKLON
1.0:E53
Assembly:
Install the ejector sleeve (13) on the
valve housing (10). Press the sleeve into
the low pressure valve so the slits of
the sleeve are exceedingly small.
Lubricate:
Grease:
Oil:
1. Install the o-ring (6) on the valve seat
(5). Make sure that the sealing
surface is not damaged.
2. Lubricate the ball joint. Tilt the
position head according to the
figure to ensure that it rotates and
articulates smoothly.
3. Remove the rubber plate (7) with an
awl and make sure the sealings
surface on the valve is clean. Install
the new rubber plate.
4. Put the spring (9) on the valve
piston (8). Lubricate the spring
5. Install the valve piston/spring in the
valve housing with the flat part of
the valve piston upwards.
Sealing surfaces
CYKLON
1.0:E54
1. Place the valve housing on a
drift seated on a block.
Press the valve housing down,
compressing the spring. Keep
the flat part of the valve piston
parallel with the horizontal slot
in the end of the valve housing.
Move the valve piston up and
down a few times to check for
freedom of movement.
2. Press the valve housing down
and slide an o-ring remover
through the hole in the valve
piston. See diagram.
3. Lubricate the o-ring and the
thread of the valve seat. Screw
in the valve seat with an 8.5 mm
screw driver until the o-ring
remover comes loose.
4. Install the operating device (14).
Insert the lever pin (11) through
the slot, engaging the hole in
the operating device. Rotate the
lever pin 90 degrees to lock it in
place.
CYKLON
1.0:E55
1. Install the o-ring (12).
Lubricate. See diagram.
2. Install the mouth piece (16) and
the plastic band (17). Tighten
and cut off plasticband with
plastic band pliers.
3. Install the o-ring .(12)
4. Lubricate the threads on the
mouth piece
5. Install the low pressure valve
(15) in the mouth piece tube.
Set the indent notch at the top
of the valve housing against the
key at the top of the mouth
piece tube. Screw on the
connecting ring (4).
6. Screw the valve seat down until
the highest part of the
operating device is even with
the level og the opening of the
mouth piece tube. Hold the
second stage valve vertically.
See fig.
CYKLON
1.0:E56
1. Install the purge button (26) in
the cover (24).Screw the button
in the cover-cavity
2. Install the inhalation diaphragm
(23) on the diaphragm housing
(22).
3. Seat the lip on the diaphragm
into the recess on the inner rim
of the diaphragm housing. Use
an o-ring remover or other
blunt pointed instrument.
4. Set the inhalation cover (24) on
the diaphragm housing over the
diaphragm.
5. Place the diaphragm housing
complete with diaphragm and
cover into the frame of the
assembly tool.
6. Insert the locking ring (25) into
the upper groove of the press of
the assembly tool. See diagram
7. Place the press on top on the
diaphragm housing.
8. Tum the knob until you hear or
feel a slight click. Continue
turning until you encounter
resistance, then back off the
knob to release the housing.
9. Check the locking ring
placement to make sure that it
has completely entered the
groove.
CYKLON
1.0:E57
1. Install the exhalation diaphragm
(21) on the diaphragm housing.
Control that the diaphragm is
packing on the diaphragm
housing.
2. Install exhalation diaphragm
cover (20) and locking ring (19).
3. Install the diaphragm housing
on the mouthpiece tube. Be
sure to slip the operating device
into the diaphragm guide
sleeve.
4. Checking the second stage for
leaks: Place the mouth piece
against your lips the low
pressure hose correction with
your thumb and inhale lightly.
This will create a partial vacuum
inside the second stage. If the
pressure does not equalize in 5
seconds the second stage leaks.
See chapter Fault-tracing
scheme.
5. Install the o-ring (2) on the LP
hose and lubricate
6. Screw on the LP-hose. Do not
tighten the connecting ring
until after the function test.
Tabla de contenidos
Otros manuales de Instrumento de buceo de POSEIDON
POSEIDON
POSEIDON 3720 Guía de configuración
POSEIDON
POSEIDON 3790 Guía de configuración
POSEIDON
POSEIDON MKVI Manual de usuario
POSEIDON
POSEIDON EBS MkII Manual de usuario
POSEIDON
POSEIDON Jetstream Guía de configuración
POSEIDON
POSEIDON 2801 Guía de configuración
POSEIDON
POSEIDON PLATFORM Manual de usuario
POSEIDON
POSEIDON Rebreather BCD Manual de usuario
POSEIDON
POSEIDON 2305 Guía de configuración
POSEIDON
POSEIDON Xstream Series Manual de usuario
POSEIDON
POSEIDON Besea Series Manual de usuario
POSEIDON
POSEIDON M28 Manual de usuario
POSEIDON
POSEIDON DRYSUITS Manual de usuario
POSEIDON
POSEIDON XSTREAM Manual de usuario
POSEIDON
POSEIDON SE7EN Manual de usuario
POSEIDON
POSEIDON M28 Manual de usuario
POSEIDON
POSEIDON Xstream Series Manual de usuario
POSEIDON
POSEIDON Cyklon 5000 Manual de usuario
POSEIDON
POSEIDON 0336 - 164 Manual de usuario
POSEIDON
POSEIDON MKVI Manual de usuario
