Polsen UWM-2 Manual de usuario
PRODUCT
MANUAL
UWM-2
WIRELESS
LAVALIER
MICROPHONE
DUAL CHANNEL UHF
TRANSMITTER
TR A N S M I T T E R
RECEIVER
2
THANK YOU FOR CHOOSING POLSEN.
The Polsen UWM-2 is a camera mountable 100-channel UHF wireless system that can transmit audio up to
300 feet. This wireless mic system is engineered with professional features like headphone monitoring, line
input, and frequency agility, which make it ideal for video applications such as interviews, lectures, dialog,
and conferences. You can choose from 100 channels to avoid interference. Up to four UWM-2 systems can be
deployed simultaneously in the same location. Whether you’re using a camcorder, DSLR camera, or portable
recorder, you’ll capture pristine and broadcast-quality audio.
The receiver features a line output and included 2-channel XLR cable for professional cameras. It also includes
a cable for recording your audio to a DSLR, consumer camcorder, or smartphone that has a 1/8 in. (3.5 mm)
mic input. The system’s transmitter features a gain control that ensures an optimum signal level for the
receiver. It’s also equipped with a line input that enables the transmission of such devices as an audio mixer,
smartphone, or portable recorder.
This wireless microphone system operates in the UHF 500 MHz bandwidth, assuring less susceptibility to
interference than VHF systems and greater reliability at longer distances. Operating in this bandwidth also
ensures that the UWM-2 system is future proof and meets current and known future FCC regulations.
3
PRECAUTIONS
•Exposure to high sound levels can cause permanent hearing loss. Avoid listening at high volumes for
extended periods of time.
• Keep this unit away from water and any ammable gases or liquids.
•Handle this product with care.
•Clean this product with only a soft, dry cloth.
•Keep this product away from children.
•Use only parts provided by the manufacturer.
•All images are for illustrative purposes only.
4
RECEIVER
1. Antennas
2. Audio output
3. Power indicator
4. Headphone output
5. Power button
6. LCD screen
7. Charging status indicator
8. USB Micro-B charging port
9. Left and right buttons
10. Set button
11. Battery compartment
12. 1/8 in. (3.5 mm) TRS to TRRS cable
13. 1/8 in. (3.5 mm) TRS to dual XLR cable
14. Shoe-mount adapter with 1/4-20 socket
15. Belt clip
RECEIVER
2.
1.
3.
4.
5.
6.
7.
8.
10.
11.
9.
12.
13.
14.
15.
5
LCD SCREEN RECEIVER
1. Battery indicator
2. Transmitter status indicator (Channel A)
3. RF reception indicator (Transmitter A)
4. Battery status (Transmitter A)
5. Audio level meter (Transmitter A)
6. Channel indicator
7. Output level indicator
8. Audio output mode indicator
9. Transmitter status indicator (Channel B)
10. Channel status indicator
11. RF reception indicator (Transmitter B)
12. Battery status (Transmitter B)
13. Audio level meter (Transmitter B)
1.
2.
3.
4.
5.
6.
7.
8.
9.
11.
12.
13.
10.
6
TRANSMITTER
1. Antenna
2. Line level input
3. Power indicator
4. Mic level input
5. Mute button
6. Power button
7. LCD screen
8. Charging status indicator
9. USB Micro-B charging port
10. Left and right buttons
11. Set button
12. Battery compartment
13. Foam windscreen (×2)
14. Shoe-mount adapter with 1/4-20 socket
15. Omnidirectional lavalier microphone (×2)
TR A N S M I T T E R
2.
1.
3.
4.
6.
7.
8.
9.
11.
12.
10.
5.
17.
18.
16.
15.
14.
16. Tie clip (×2)
17. Shoe mount
18. Belt clip
13.
7
LCD SCREEN TRANSMITTER
1. RF transmission power indicator
2. Mute indicator
3. Transmitter channel selector
4. Low-cut lter
5. Function lock
6. Battery indicator
7. Mic / Line indicator
8. Frequency channel selector / Input level (Gain)
9. Frequency indicator
10.Level meter
1.
7.
2. 3. 4. 5. 6.
8.
10.
9.
8
INSTALLING THE BATTERIES
Transmitter and Receiver
The transmitter and receiver are each powered by two AA batteries. To install the batteries, follow these steps.
1. Make sure the units are turned off by pressing and holding the power button on all units.
2. Pinch the battery compartment tabs together, and the compartment door will pop open.
3. Insert fresh batteries, following the orientation diagram on the back of the unit.
4. Press the compartment door down over the batteries until it locks into place.
Rechargeable Batteries
You can use rechargeable AA batteries with the receiver and transmitter.
To recharge:Place them in the battery compartment and connect the receiver or transmitter to a powered USB
port or charging device with a Micro-USB to USB Standard-A cable (not included).
Charging status indicator:
RED Charging in progress
GREEN Charging complete
Important!Do not attempt to recharge non-rechargeable batteries—this may result in damage to the unit and
void the warranty.
9
Tip:Before you record, insert fresh batteries into the transmitter and receiver. Have spare fresh batteries on hand
during a session. If you’re using rechargeable batteries, bring extra batteries and a battery charger with you.
MOUNTING
The transmitter and receiver can be worn attached to a belt or mounted on a camera, or attached to a tripod or
articulating arm.
Belt Clip
Attach the included belt clip by pinching the two ends together and inserting them
into the holes on the back of the unit.
Shoe Mount
The transmitter and receiver can be attached to your camera with the shoe-mount
adapter. You can also move the unit off your camera by attaching it to the shoe
mount that’s built into many ring lights, LEDs, and articulating arms.
1. Attach the shoe-mount adapter by tting the two hooks over each side of the
belt clip’s center section.
2. Loosen the shoe-mount adapter’s locking wheel by turning it clockwise, and slide
it into the shoe mount. Make sure it’s fully inserted, then turn the locking wheel
counterclockwise to tighten until it’s secure.
10
Tripod Mounting
If you prefer a secure stationary place for the transmitter or receiver, mount it to an accessory with a 1/4-20
mounting screw like a tripod or light stand.
1. Follow the instructions above for attaching the shoe-mount adapter.
2. Use the 1/4-20 socket on the shoe-mount adapter to screw the unit onto a tripod or light stand that has a
1/4-20 mounting screw.
BEFORE YOU BEGIN
The UWM-2 Dual Channel Wireless System is intuitive and easy to operate.
If you choose to begin using the system before reading the operating instructions, follow these operating tips:
Channel Selection
The transmitters and the receiver must all be set to the same channel number whether the transmitters are set to
transmitter channel A or B.
See
Setting the Receiver Channel
and
Setting the Transmitter Channel
below.
Locking Connectors
To ensure the cables are not disconnected from the UWM-2 during a recording or performance, the included cables
have locking 1/8 in. (3.5 mm) connectors.
Tabla de contenidos
Otros manuales de Micrófono de Polsen
Polsen
Polsen M-85 Manual de usuario
Polsen
Polsen MC-POD Manual de usuario
Polsen
Polsen RC-77-U Manual de usuario
Polsen
Polsen MO-IPL2 Manual de usuario
Polsen
Polsen MVP-6 Manual de usuario
Polsen
Polsen HH-IC Manual de usuario
Polsen
Polsen SCL-1075 Manual de usuario
Polsen
Polsen XP-2 Manual de usuario
Polsen
Polsen DPM-7 Manual de usuario
Polsen
Polsen VM-101 Manual de usuario
Polsen
Polsen MVP-3 Manual de usuario
Polsen
Polsen MO-IDL2 Manual de usuario
Polsen
Polsen SCL-1080 Manual de usuario
Polsen
Polsen US-OB-55 Manual de usuario
Polsen
Polsen GM3-USB Manual de usuario
Polsen
Polsen MO-IDL1 Manual de usuario
Polsen
Polsen MO-CPL2 Manual de usuario
Polsen
Polsen RM-800 Manual de usuario
Polsen
Polsen M-70 Manual de usuario
Polsen
Polsen SMS-45A Manual de usuario
