Point Mobile PM351 Manual de usuario
V1.0, May 2022
Copyright © 2022 Point Mobile Co., Ltd. All rights reserved.
Point Mobile Co., Ltd. is the designer and manufacturer of mobile handheld devices.
The Point Mobile logo is a registered trademark and symbol of Point Mobile Co., Ltd.
Features and specifications are subject to change without prior notice.
PM351
Quick Start Guide
Device Parts
1. Scanner & Camera
2. LED indicator
3. Touch screen
4. Keypad
5. USB connector
6. Power button
7. Microphone
2
1
57
3
4
6
Device Parts
8. Speaker
9. Hand strap hole (Top)
10. I/O connector (Rear)
11. Battery
12. Battery release button
13. Hand strap hole (Bottom)
14. I/O connector (Bottom)
10
9
8
14
13
11
12
Product Standard Accessories
LCD protection film
Battery Replacement
1. Align the battery release button to the bottom side. And
insert the battery from the top side of the device.
2. Push the battery down until it clicks, and check if the
battery is firmly engaged.
Pull up the bottom side of the battery while pressing the
battery release button.
Battery pack
Insert Battery
Remove Battery
Caution: Make sure the SIM and SD card holders are completely closed
before inserting the battery.
Stylus penHand strap
USB type C cable
AC Plug
5V 2A power adapter
Installing SIM, SD card
PM351 supports micro SIM and microSD card. (SIM card is
supported by LTE SKU only.)
Turning on / off
Turn on
Turn off
Press and hold the Power button on the keypad until
SMART BEYOND RUGGED logo displays on the screen.
When the screen is on, press and hold the Power button
until the power menu is shown.
Then, tap Power off among the menu.
1. Gently slide the cardholder up, and swing upwards.
2. Put the SIM card facing down the gold contact.
3. Close the holder down and slide it down to lock.
SIM card
1. Gently slide the cardholder down, and swing upwards.
2. Put the SIM card facing down the gold contact.
3. Close the holder down and slide it up to lock.
SD card
Alpha-NumericNumeric
Charging the Device
1. Assemble the AC plug, power adapter and USB cable.
2. Connect the cable to the USB connector of PM351.
3. Provide power by plugging the power adapter to the wall
socket.
PM351 can also be charged with charging cradle
(sold separately).
LED Indicator
< Caution >
1. Always use an original power supply from Point Mobile. Other
chargers and cables may damage the PM351.
The device warranty does not cover any damage caused by the
usage of non-original power supplies.
2. Make sure the charger and cable is not wet.
2
No
Indicator
Status
Indication
1
Power
LED
Solid
green
Device
is fully charged
Solid
red
Charging
the device / Battery is low
Blinking
red
Charging temperature is out of
normal range / Battery is very low
Alternately blinking
red
&green
Cannot
recognize the battery
2
Notification
LED
Solid
red
Device
entered hot swap mode
Blinking
blue
Notification
existing
Red
flash
Barcode
reading failed
Blue
flash
Barcode
reading success
1
Using Keyboard Backlight
Use keyboard backlight when the keypad is not visible in the
dark place.
Scan a Barcode
Scanner is placed on the top of the PM351.
Center the aimer (laser bar, green dot, or red dot) over the
barcode.
SE4100 Scanner SKU
SE4710 Scanner SKU
Scanner is disabled by default, so enable the scanner from
ScanSettings first.
Then, press a scan button on the device to scan a barcode.
1. Go to Settings > Display
2. Turn the Keyboard Backlight switch on.
SE965 Scanner SKU
Otros manuales para PM351
1
Tabla de contenidos
Otros manuales de Terminal táctil de Point Mobile
Point Mobile
Point Mobile HTK10 Manual de usuario
Point Mobile
Point Mobile PM66 Manual de usuario
Point Mobile
Point Mobile PM30 Manual de usuario
Point Mobile
Point Mobile PM30 Manual de usuario
Point Mobile
Point Mobile PM500 Manual de usuario
Point Mobile
Point Mobile PM80 Manual de usuario
Point Mobile
Point Mobile PM40 Manual de usuario
Point Mobile
Point Mobile PM451 Manual de usuario
Point Mobile
Point Mobile XM5 Manual de usuario
Point Mobile
Point Mobile PM500 Manual de usuario
