PMFoundations ADSR-D Manual de usuario

Page 1 of 11

ADSR-D v1.0 –Assembly Guide

Thank you for purchasing this module! This is an easy build. Some of the pads are quite small and

you will need a chisel tip or screwdriver tip soldering iron and the skill to solder these tiny joints.

This module is also used in the reSEMble semi-modular synth. YOU DO NOT NEED TO AND SHOULD

NOT INSTALL THE PARTS that are specific to the reSEMble synth. These parts are not included in the

BOM. These are the parts marked on the PCB that are not required:

SV1, SW1, S1

The module is designed and sized for Eurorack systems. You will need a 16-10 pin eurorack power

ribbon connector with –12/0/+12 which is connected to a synth power supply.

Follow the parts lists, these instructions and the PCB silkscreen text to build the module.

The module consists of 1 PCB board and a front panel.

You must follow the order of assembly as described below since some components will be soldered

underneath other components.

Page 2 of 11

Constructing the board

Resistors

For a 5V envelope instead of a 10V envelope replace R22 with 27K and replace R23 with 4.7K.

Install the flat resistors on the TOP of the board. Solder and clip the leads.

Diodes (but not LEDs)

Install the diodes on the TOP of the board. Align the stripe on each diode with the stripe marked on the

board. Solder and clip the leads. Now go back and check the polarity against the silk screen for each

diode.

Page 3 of 11

Ceramic/film capacitors

Install the ceramic/film capacitors on the TOP of the board. Solder and clip the leads.

Page 4 of 11

Tantalum capacitor

Install this on the TOP. Make sure you orient these capacitors correctly. The longer lead and/or the lead

marked with a + needs to be inserted into the hole that has the “+” marking near it. Leads marked with

“-“ go in the board hole WITHOUT the “+”. Solder and clip the leads.

Bipolar Transistors

Install the transistors on the TOP of the board. Do not mix up the NPNs with the PNPs. These are

polarized components. Align the outline with the outline on the board. They should be raised off the

board surface slightly and at the same height. Solder and clip the leads.

Page 5 of 11

Power socket

Install the 10 pin power socket on the TOP of the board. This must be installed with the correct

orientation or the module will be damaged when the power is connected.

The cut-out in the socket should face the pots, aligning the cut-out with the "10" marking on the board

as shown in the photo.

Page 6 of 11

Potentiometers

If the pots have positioning lugs on the front, cut these off with a sharp pair of flush cutting pliers. The

front of the pot (where the shaft protrudes) needs to be flat.

There are 1M and 100k puts. Do not mix these up.

Carefully align the pots so they are flush with the edge of the board and perfectly upright and tight to

the board surface. They must be installed on the TOP of the board. Please ensure they are on the

CORRECT SIDE OF THE BOARD before soldering otherwise PCB tracks and pads may be damaged if they

are desoldered. See Photo.

Page 7 of 11

Switch

Insert the switch on the BOTTOM so that the plunger faces the front of the PCB. There are two

unused location holes. Tack one pin of the switch, align with the front panel, then solder all the

remaining pins and the locating lugs. The switch is on the BOTTOM. Do not bridge the contacts

to nearby components.

Page 8 of 11

3.5mm Jack Sockets

Install the jacks on the TOP and BOTTOM and fully solder each one as you install it. Make sure they are

perfectly aligned and tight to the board. Please ensure they are on the CORRECT SIDE OF THE BOARD

before soldering otherwise PCB tracks and pads may be damaged if they are desoldered.

Do not bridge the contacts to nearby components.

Page 9 of 11

LED

Bend the leads as shown in the photo. The bend is at 14mm from the base of the LED lens. Insert in the

TOP of the board with the long lead in the hole marked + and use the panel to align the LED. Solder the

LED and clip the leads.

Page 10 of 11

Tabla de contenidos

Otros manuales de Unidad de control de PMFoundations

PMFoundations

PMFoundations Clock Divider Manual de usuario

PMFoundations

PMFoundations ER-808 Manual de usuario

PMFoundations

PMFoundations Euro-ADSR Manual de usuario

PMFoundations

PMFoundations My Little Mixer Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

PMFoundations

PMFoundations Switch4 Manual de usuario

PMFoundations

PMFoundations 3080 VCO v1.2 Manual de usuario

PMFoundations

PMFoundations Buffered Multipl Manual de usuario

PMFoundations

PMFoundations Dual VCA Manual de usuario

PMFoundations

PMFoundations 6080 VCO Manual de usuario

PMFoundations

PMFoundations Clock Manual de usuario

PMFoundations

PMFoundations State Machine Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario

Flyron

Flyron FN-BC04 Manual de usuario