PLC Buildings Bantam Manual de programación
B
B
ANTAM
L
IGHTING
C
ONTROLLER
S
OFTWARE
M
ANAGEMENT
G
UIDE
207 Bantam Software Management Guide Rev1
B
BANTAM LIGHTING CONTROL SYSTEM
Software Management Guide
Date: 10/14/2014
Rev: 1
10/14/2014 3101 111th ST SW #F, Everett WA. 98204
Phone: 425-353-7552 / Fax: 425 353-3353
WEB: www.plcmultipiont.com
Page 2 of 18
TABLE of CONTENTS
1.0 OVERVIEW.......................................................................................................................3
1.1.1 SYSTEM OVERVIEW...............................................................................................................3
1.1.2 PURPOSE............................................................................................................................3
1.1.3 EQUIPMENT AND PARTS .........................................................................................................3
2.0 RUN-TIME SOFTWARE UPGRADE PROCEDURE OPTIONS.............................................4
3.0 RUN-TIME SOFTWARE UPDATE – WITH A MICROSD...................................................5
4.0 BANTAM CONFIGURATION SOFTWARE BACKUP / RESTORE – WITH A MICROSD....5
4.1 BACKUP AND RESTORE TO MICROSD...........................................................................................6
4.2 BACKUP................................................................................................................................6
4.3 RESTORE..............................................................................................................................6
5.0 BANTAM CONTROLLER CLEAR CONFIGURATION PROFILE ..........................................7
6.0 HYPERTERMINAL INSTALLATION AND CONNECTION TO BANTAM.............................8
6.1 INSTALL HYPERTERMINAL ON THE SELECTED COMPUTER ..................................................................8
6.2 ATTACH THE REQUIRED CABLE TO THE BANTAM .............................................................................8
6.3 DOUBLE CLICK ON THE HYPERTERMINAL.EXE FILE TO START THE APPLICATION .......................................8
6.4 CREATE A NEW HYPERTERMINAL USER NAME .................................................................................8
6.5 SELECT THE NEW OR UNUSED COM-PORT ......................................................................................9
6.6 SELECT THE FOLLOWING COMMUNICATION PROFILES,AND PRESS OK...................................................9
6.7 PRESS THE ESC KEY ON THE COMPUTER KEYBOARD TO ESTABLISH A CONNECTION TO THE BANTAM............10
7.0 RUN-TIME SOFTWARE UPDATE – WITH THE BANTAM USB PORT...........................11
7.1 CONNECT THE BANTAM USB PORT TO A COMPUTER VIA HYPERTERMINAL .............................................11
8.0 BANTAM CONFIGURATION BACKUP / RESTORE – USING THE USB PORT ...............14
8.1 BACKUP CONFIGURATION TO A COMPUTER VIA THE USB PORT AND HYPERTERMINAL...............................14
8.2 RESTORE CONFIGURATION TO A BANTAM VIA THE USB PORT AND HYPERTERMINAL. ...............................16
9.0 VERIFY THE CORRECT SOFTWARE BUILD UPDATE.....................................................18
B
BANTAM LIGHTING CONTROL SYSTEM
Software Management Guide
Date: 10/14/2014
Rev: 1
10/14/2014 3101 111th ST SW #F, Everett WA. 98204
Phone: 425-353-7552 / Fax: 425 353-3353
WEB: www.plcmultipiont.com
Page 3 of 18
1.0 OVERVIEW
1.1.1 System Overview
The Bantam is an easy to use, quick to install, single panel lighting control system which doesn’t
require any additional relays or contactors to activate the load. The Bantam is designed to be
controlled locally via the built in LCD screen and integrated touch pad and also via a USB
communication link using HyperTerminal as the serial protocol application. Bantam software updates
may be accomplished using either the USB port or a 2GB MicroSD card.
1.1.2 Purpose
This Software Management Guide will provide the necessary instructions needed for software
updates, backup, restore and profile clear operations using the Bantam USB port or a 2GB MicroSD
Card.
1.1.3 Equipment and Parts
1. 2GB MicroSD Card, (PN: COMSD2)
2. 4 pin USB Type A-Male to 4 pin mini-USB Type B-Male, (PN: COUSB).
3. Desktop or Portable Computer (PC) with HyperTerminal installed.
B
BANTAM LIGHTING CONTROL SYSTEM
Software Management Guide
Date: 10/14/2014
Rev: 1
10/14/2014 3101 111th ST SW #F, Everett WA. 98204
Phone: 425-353-7552 / Fax: 425 353-3353
WEB: www.plcmultipiont.com
Page 4 of 18
2.0 RUN-TIME SOFTWARE UPGRADE PROCEDURE OPTIONS
Using a MicroSD Card perform the following when upgrading Bantam software.
1. Perform a Configuration Backup, Section 4.
2. Perform a Software Update, Section 3.
3. Perform a Clear Configuration profile, Section 5.
4. Perform a Configuration Restore, Section 4.
5. Verify the correct software build serial numbers, Section 9.
Using the USB port, perform the following when upgrading Bantam software.
1. Perform a Configuration Backup, Section 8.2.
2. Perform a Software Update, Section 7.
3. Perform a Clear Configuration profile, Section 5.
4. Perform a Configuration Restore, Section 8.3.
5. Verify the correct software build serial numbers, Section 9.
B
BANTAM LIGHTING CONTROL SYSTEM
Software Management Guide
Date: 10/14/2014
Rev: 1
10/14/2014 3101 111th ST SW #F, Everett WA. 98204
Phone: 425-353-7552 / Fax: 425 353-3353
WEB: www.plcmultipiont.com
Page 5 of 18
3.0 RUN-TIME SOFTWARE UPDATE –WITH A MICROSD
Follow this procedure to update the firmware - (BANTAMV1.bin) with a MicroSD card.
Place the Auto/Manual switch in Manual mode.
Press and hold the EXIT button.
While holding the EXIT button, press and release the RESET button.
The LOAD PROGRAM MENU is displayed:
1LOADPROGRAM
FROMUSBPORT
2LOADPROGRAM
FROMMICROSD
The 2GB MicroSD card MUST be in the slot, and the BANTAMV1.bin file MUST be on the MicroSD.
Press 2 on the Bantam keypad.
The following display will appear:
ERASING EXISTING
FIRMWARE………
When completed, the following display will appear:
TRANSFERRING
FILE………….
Once the file transfer is complete, the LOAD PROGRAM MENU will reappear.
Place the Auto/Manual switch in the Auto position.
Press the Bantam RESET button to resume normal controller operation.
4.0 BANTAM CONFIGURATION SOFTWARE BACKUP /RESTORE –WITH A MICROSD
B
BANTAM LIGHTING CONTROL SYSTEM
Software Management Guide
Date: 10/14/2014
Rev: 1
10/14/2014 3101 111th ST SW #F, Everett WA. 98204
Phone: 425-353-7552 / Fax: 425 353-3353
WEB: www.plcmultipiont.com
Page 6 of 18
A 2GB MicroSD card MUST be installed in the Bantam.
4.1 BACKUP AND RESTORE TO MICROSD
How to get here: PRESS PROGRAM SYSTEM SETUP 9
Use UP/DOWN to highlight
BACKUP/RESTORE. Push SELECT.
Quick key: Push 9.
4.2 BACKUP
Use UP/DOWN to highlight BACKUP.
Push SELECT
Quick key: Push 1
Use UP/DOWN to highlight TO MICROSD.
Push SELECT
Quick key: Push 2
This will place the backup file on the
MicroSD.
4.3 RESTORE
Use UP/DOWN to highlight RESTORE.
Push SELECT
Quick key: Push 2
Use UP/DOWN to highlight FROM
MICROSD. Push SELECT
Quick key: Push 2
The backup file will come from the
MicroSD.
9 BACKUP/RESTORE
1 BACKUP P
2 RESTORE
1 TO USB
2 TO MICROSD P
1 BACKUP
2 RESTORE E
1 FROM USB
2 FROM MICROSD P
DOWN
SELECT
UP
UP
DOWN
SELECT
DOWN
SELECT
UP
DOWN
SELECT
DOWN
SELECT
UP
UP
B
BANTAM LIGHTING CONTROL SYSTEM
Software Management Guide
Date: 10/14/2014
Rev: 1
10/14/2014 3101 111th ST SW #F, Everett WA. 98204
Phone: 425-353-7552 / Fax: 425 353-3353
WEB: www.plcmultipiont.com
Page 7 of 18
5.0 BANTAM CONTROLLER CLEAR CONFIGURATION PROFILE
Follow this procedure to clear all configuration profiles in the Bantam.
Press the following buttons:
RESET -> PROGRAM -> (4) OR SYSTEM SETUP -> (7) OR SET DEFAULTS -> PROGRAMS
The following screen will appear:
ARE YOU SURE YOU
WANT ALL USER
PROGRAMS SET TO
DEFAULTS: YES
Use the RAISE or LOWER buttons to select YES, and then press the SELECT button.
Once the Clear process is complete the following screen will appear:
5 …NOT USED
6 WARN/SWEEP
7 SET DEFAULTS
8 POWERUP INPUT
Press the Exit button twice or Reset button to return to the top Menu screen.
B
BANTAM LIGHTING CONTROL SYSTEM
Software Management Guide
Date: 10/14/2014
Rev: 1
10/14/2014 3101 111th ST SW #F, Everett WA. 98204
Phone: 425-353-7552 / Fax: 425 353-3353
WEB: www.plcmultipiont.com
Page 8 of 18
6.0 HYPERTERMINAL INSTALLATION AND CONNECTION TO BANTAM
6.1 INSTALL HYPERTERMINAL ON THE SELECTED COMPUTER
6.2 ATTACH THE REQUIRED CABLE TO THE BANTAM
6.3 DOUBLE CLICK ON THE HYPERTERMINAL.EXE FILE TO START THE APPLICATION
6.4 CREATE A NEW HYPERTERMINAL USER NAME
B
BANTAM LIGHTING CONTROL SYSTEM
Software Management Guide
Date: 10/14/2014
Rev: 1
10/14/2014 3101 111th ST SW #F, Everett WA. 98204
Phone: 425-353-7552 / Fax: 425 353-3353
WEB: www.plcmultipiont.com
Page 9 of 18
6.5 SELECT THE NEW OR UNUSED COM-PORT
6.6 SELECT THE FOLLOWING COMMUNICATION PROFILES,AND PRESS OK
Baud: 115200
Data Bits: 8
Parity: None
Stop Bits: 1
Flow: None
B
BANTAM LIGHTING CONTROL SYSTEM
Software Management Guide
Date: 10/14/2014
Rev: 1
10/14/2014 3101 111th ST SW #F, Everett WA. 98204
Phone: 425-353-7552 / Fax: 425 353-3353
WEB: www.plcmultipiont.com
Page 10 of 18
6.7 PRESS THE ESC KEY ON THE COMPUTER KEYBOARD TO ESTABLISH A CONNECTION TO THE BANTAM
Once the ESC key is pressed, the HyperTerminal application should be established with the
Bantam. If properly connected, the following screen should appear.
The following computer keys are used to simulate the onboard Bantam keys.
BANTAM KEY COMPUTER KEY
SELECT ENTER
UP,DOWN,LEFT,RIGHT UP,DOWN,LEFT,RIGHT
RAISE CTRL-R
LOWER CTRL-L
SAVE CTRL-S
SPACE SPACE
EXIT ESC
0-9
(
numeric
)
0-9
0-9
(
al
p
ha-numeric
)
A-Z, a-z, 1-9, 0
RY1-RY8 NO KEYS
Tabla de contenidos
