Planet WAP-8000 Manual de usuario

802.11a/b/g Wireless LAN Outdoor AP

WAP-8000

Quick Installation Guide

Table of Contents

Package Content.............................................................................................. 4

Outlook........................................................................................................... 5

Hardware Installation ....................................................................................... 6

OUTDOOR INSTALLATION WARNING.................................................................. 8

Web Conguration .........................................................................................10

Further Conguration ......................................................................................11

Designed with Dual band 802.11a and 802.11b/g technology, WAP-8000 provides

108Mbps Super A+G mode high data rate for outdoor environment. There are four

operating modes supported in WAP-8000: AP, Bridge, AP Client and WISP. With

external N-type connector design and higher RF output power make WAP-8000 a

suitable CPE solution for widely open space applications such as WISPs, campuses,

and airports. Except for 64/128-bit WEP encryption, WAP-8000 integrates WPA,

WPA2 encryption to secure the information of your wireless LAN.

Package Content

WAP-8000 x 1

PoE injector x 1

Power Adapter x 1

Mounting Kit (with screw package) x 1

Weatherproof connector x 1

CD-ROM x 1

Quick Installation Guide x 1

Note

If any of the above items are missing or damaged, contact your

local dealer for support.

Outlook

1. On the back panel of WAP-8000, there are LEDs indication

(LAN, WLAN, PWR).

2. On the bottom of WAP-8000, there are three interfaces.

(N-type antenna connector, Reset button, LAN port).

N-type

Antenna

connector

Reset

button

LAN

port

Hardware Installation

Before you proceed with the installation, it is necessary that you have enough

information about WAP-8000.

1. Plug in the waterproof connector on RJ-45 cable.

Step1 Step2

Note

Strongly suggest using SFTP cable, for better protection of the data

wire. 25-meter SFTP cable also available by order, the part no is

CB-STP-25. Please contact with local dealer for more information

2. Connect RJ-45 cable with the waterproof connector to the LAN port of WAP-8000

and another way connect to the “PoE” port of PoE Injector. Connect antenna to

N-type antenna connector.

Connect

antenna

3. Lock the waterproof connector into outside circle of the LAN port.

Step1 Step2

4. Locate an optimum location and use the provided Mounting kit to tie the WAP-

8000 to a pole.

Step3

Step1 Step2

Note

For secured reason, while install the CPE AP, please be aware for

the electric wires around, and tighten the pole.

Without tighten the CPE AP, the pole and the installed site is with

electric wire around, there could be danger of being hurt by falling

or lethal injury.

5. Connect the “LAN” port of PoE Injector to Ethernet hub, switch or PC on the

same LAN for management.

6. Connect the power adapter to the PoE Injector, and plug it into an AC outlet to

power on the WAP-8000.

Note

1. ONLY use the power adapter supplied with the WAP-8000. Other-

wise, the product may be damaged.

2. Strongly suggest using SFTP cable whether the cable exposed

outdoor for waterproof and avoiding thunder stroke.

OUTDOOR INSTALLATION WARNING

IMPORTANT SAFETY PRECAUTIONS:

LIVES MAY BE AT RISK! Carefully observe these instructions and any special

instructions that are included with the equipment you are installing.

CONTACTING POWER LINES CAN BE LETHAL.

Make sure no power lines are anywhere

where possible contact can be made.

Antennas, masts, towers, guy wires or

cables may lean or fall and contact these

limes. People may be injured or killed if

they are touching or holding any part

of equipment when it contacts electric

lines. Make sure there is NO possibility

that equipment or personnel can come in

contact directly or indirectly with power

lines.

Assume all overhead lines are power lines.

The horizontal distance from a tower, mast or antenna to the nearest power line

should be at least twice the total length of the mast/antenna combination. This will

ensure that the mast will not contact power if it falls either during installation or

later.

TO AVOID FALLING, USE SAFE PROCEDURES WHEN WORKING AT HEIGHTS

ABOVE GROUND.

Select equipment locations that will allow safe, simple equipment installation.

Don’t work alone. A friend or co-worker can save your life if an accident

happens.

Use approved non-conducting lasers and other safety equipment. Make sure all

equipment is in good repair.

If a tower or mast begins falling, don’t attempt to catch it. Stand back and let

it fall.

If anything such as a wire or mast does come in contact with a power line,

DON’T TOUCH IT OR ATTEMPT TO MOVE IT. Instead, save your life by

calling the power company.

Don’t attempt to erect antennas or towers on windy days.

MAKE SURE ALL TOWERS AND MASTS ARE SECURELY GROUNDED, AND

ELECTRICAL CABLES CONNECTED TO ANTENNAS HAVE LIGHTNING

ARRESTORS. This will help prevent re damage or human injury in case of

lightning, static build-up, or short circuit within equipment connected to the

antenna.

The base of the antenna mast or tower must be connected directly to the

building protective ground or to one or more approved grounding rods, using 1

OAWG ground wire and corrosion-resistant connectors.

Refer to the National Electrical Code for grounding details.

IF A PERSON COMES IN CONTACT WITH ELECTRICAL POWER, AND

CANNOT MOVE:

DON’T TOUCH THAT PERSON, OR YOU MAY BE ELECTROCUTED.

Use a non-conductive dry board, stick or rope to push or drag them so they no

longer are in contact with electrical power.

Once they are no longer contacting electrical power, administer CPR if you are

certied, and make sure that emergency medical aid has been requested.

Web Conguration

WAP-8000 provides a user friendly interface for users to congure via web browser.

Please follow the below steps to congure WAP-8000 basic settings.

1. It will take a few seconds to complete the boot up sequence after power on

from PoE.

2. Before conguration of WAP-8000, please note that your PC’s IP address should

be on the same IP subnet (http://192.168.1.x) of the WAP-8000 (Please follow

the manual for assign a static IP address to set same IP subnet).

3. Open your web browser.

Default IP Address: http://192.168.1.1

Default IP subnet mask: 255.255.255.0

WEB login User Name / Password: admin

4. After enter the password, you can see the login web page.

Otros manuales para WAP-8000

Tabla de contenidos

Otros manuales de Punto de acceso inalámbrico de Planet

Planet

Planet WNAP-6305 Manual de usuario

Planet

Planet WNAP-6305 Manual de usuario

Planet

Planet IAP-2000PS Manual de usuario

Planet

Planet WAP-4030 Manual de usuario

Planet

Planet WAP-1000 WireFree Manual de usuario

Planet

Planet WDAP-W7200AC Manual de usuario

Planet

Planet WAP-252N Manual de usuario

Planet

Planet WDAP-C7210E Manual de usuario

Planet

Planet WNAP-3000PE Manual de usuario

Planet

Planet WNAP-6350 Manual de usuario

Planet

Planet WAP-1963 Manual de usuario

Planet

Planet Wireless Access Point w/Bridge WAP-1963A Manual de usuario

Planet

Planet WDAP-C1750 Manual de usuario

Planet

Planet WNAP-1110 Manual de usuario

Planet

Planet WDAP-3000AX Manual de usuario

Planet

Planet WAP-2000 Manual de usuario

Planet

Planet MAP-3120 Manual de usuario

Planet

Planet WNAP-C3220E Manual de usuario

Planet

Planet WNAP-6308 Manual de usuario

Planet

Planet WBS-202N Manual de usuario

Planet

Planet WDAP-C7200AC Manual de usuario

Planet

Planet WNAP-6305 Manual de usuario

Planet

Planet 802.11n Wireless Access Point WNAP-1120 Manual de usuario

Planet

Planet WBS-502AC Manual de usuario

Manuales populares de Punto de acceso inalámbrico de otras marcas

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manual de usuario

Ubiquiti

Ubiquiti NanoStation NSM2 Manual de usuario

Cisco

Cisco Aironet 1550 Series Manual de usuario

Aruba

Aruba IAP-335 Manual de usuario

Advantek Networks

Advantek Networks AWN-AP-54MR Manual de usuario

IP-COM

IP-COM AP355 Manual de usuario

Buffalo

Buffalo AirStation WLA-L11G Manual de usuario

EnGenius

EnGenius EnStationACv2 Manual de usuario

D-Link

D-Link DAP-3662 Manual de usuario

xG Technology

xG Technology xMax CN1300 Manual de usuario

Widelink

Widelink ezWave WAP-1100 Series Manual de usuario

Edimax

Edimax CAP1200 Manual de usuario

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manual de usuario

Aruba

Aruba AP-203R Manual de usuario

LuXout Shades

LuXout Shades LUXSHADE MOTION Manual de usuario

CreatComm

CreatComm TB5F Manual de usuario

SineDigital

SineDigital MW-1500AP(H) Manual de usuario

TP-Link

TP-Link AP9650 V1 Manual de usuario