Planet GS-5220-8P2T2S Manual de usuario

L2+ Managed Gigabit/10 Gigabit Ethernet Switch

NEXT-3032FGL2-SFP

Quick Installation Guide

Table of Contents 
Package Contents........................................................................................ 3 
Requirements.................................................................................................. 4 
Terminal Setup............................................................................................ 5 
Logon to Console ........................................................................................ 6 
Configuring IP Address ................................................................................ 7 
Starting Web Management ........................................................................... 9 
Saving Configuration ......................................................................................12 
Recovering Back to Default Configuration........................................................13 
Customer Support ..................................................................................... 14 
 

1. Package Contents

Thank you for purchasing PLANET L2+ Managed Gigabit/10 Gigabit Ethernet

Switch. The description of this model is shown below:

Model Name

Gigabit RJ45

Ports

Gigabit SFP

Slots

PoE Ports

10G SFP+

Slots

GS-5220-8P2T2S

GS-5220-16S8C

8 combo

GS-5220-16S8CR

8 combo

GS-5220-44S4C

4 combo

GS-5220-46S2C4X

2 combo

GS-5220-48T4X

4 combo

“Managed Switch” is used as an alternative name in this Quick Installation

Guide.

Open the box of the Managed Switch and carefully unpack it. The box should

contain the following items:

The Managed Switch

Quick Installation Guide

RJ45 to RS232 Cable

Rubber Feet

Two Rack-mounting Brackets with Attachment Screws

Power Cord

SFP Dust-proof Caps

GS-5220-8P2T2S

GS-5220-16S8C(R)

GS-5220-44S4C

GS-5220-46S2C4X

GS-5220-48T4X

If any item is found missing or damaged, please contact your local reseller for

replacement.

2. Requirements

Workstations running Windows XP/2003/Vista/7/8/2008, MAC OS X or later,

Linux, UNIX, or other platforms are compatible with TCP/IP protocols.

Workstations are installed with Ethernet NIC (Network Interface Card)

Serial Port Connection (Terminal)

The above Workstations come with COM Port (DB9) or USB-to-RS232

converter.

The above Workstations have been installed with terminal emulator, such as

Hyper Terminal included in Windows XP/2003.

Serial cable -- one end is attached to the RS232 serial port, while the other

end to the console port of the Managed Switch.

Ethernet Port Connection

Network cables -- Use standard network (UTP) cables with RJ45 connectors.

The above PC is installed with Web browser and JAVA runtime environment

plug-in.

Note

It is recommended to use Internet Explore 8.0 or above to access

the Managed Switch. If the Web interface of the Managed Switch

is not accessible, please turn off the anti-virus software or firewall

and then try it again.

3. Terminal Setup

To configure the system, connect a serial cable to a COM port on a PC or

notebook computer and to RJ45 type of serial port of the Managed Switch.

PC / Workstation

with

Terminal Emulation Software

Managed Switch

Figure 3-1 Managed Switch Console Connectivity

A terminal program is required to make the software connection to the Managed

Switch.

1. Run terminal program on the OS.

2. When the following screen appears, make sure that the COM port should be

configured as:

Baud : 115200

Data bits 8

Parity : None

Stop bits 1

Flow control : None

Figure 3-2: COM Port Configuration

RJ45

Console Port

RS232 to RJ45Cable

Serial Port

4. Logon to Console

Once the terminal is connected to the device, power on the Managed Switch, and

the terminal will display “running testing procedures”. Then, the following message

asks to log-in user name and password. The factory default user name and

password are shown as follows and the login screen in Figure 4-1 appears.

Figure 4-1: Managed Switch Console Login Screen

The user can now enter commands to manage the Managed Switch. For a detailed

description of the commands, please refer to the following chapters.

Username: admin

Password: admin

Note

1. For security reason, please change and memorize the new pass-

word after this first setup.

2. Only accept command in lowercase letter under console inter-

face.

5. Configuring IP Address

The Managed Switch is shipped with default IP address shown below.

To check the current IP address or modify a new IP address for the Switch, please

use the procedures as follows:

Show the current IP Address

1. At the “#” prompt, enter “show ip interface brief”.

2. The screen displays the current IP address as shown in Figure 5-1.

Figure 5-1: IP Information Screen

Configuring IP Address

3. At the “#” prompt, enter the following command and press <Enter> as shown

in Figure 5-2.

The previous command would apply the following settings for the Managed Switch.

IP Address: 192.168.1.100

Subnet Mask: 255.255.255.0

Figure 5-2: Configuring IP Address Screen

IP Address: 192.168.0.100

Subnet Mask: 255.255.255.0

GS-5220 Series# configure terminal

GS-5220 Series(config)# interface vlan 1

GS-5220 Series(config-if-vlan)# ip address 192.168.1.100 255.255.255.0

4. Repeat step 1 to check if the IP address is changed.

Store current switch configuration

5. At the “#” prompt, enter the following command and press <Enter>

Figure 5-3: Saving Current Configuration Command Screen

If the IP is successfully configured, the Managed Switch will apply the new IP

address setting immediately. You can access the Web interface of the Managed

Switch through the new IP address.

# copy running-config startup-config

Note

If you are not familiar with the console command or the related

parameter, enter “help” anytime in console to get the help

description.

6. Starting Web Management

The following shows how to start up the Web Management of the Managed Switch.

Note the Managed Switch is configured through an Ethernet connection. Please make

sure the manager PC must be set on the same IP subnet address.

For example, the default IP address of the Managed Switch is 192.168.0.100,

then the manager PC should be set at 192.168.0.x (where x is a number

between 1 and 254, except 100), and the default subnet mask is 255.255.255.0.

PC / Workstation

with Web Browser

192.168.0.x

Managed Switch

RJ45/UTPCable

IP Address:

192.168.0.100

Figure 6-1: IP Management Diagram

Logging in the Managed Switch

1. Use Internet Explorer 8.0 or above Web browser and enter IP address

http://192.168.0.100 (the factory default IP address or the one that you have

just changed in console) to access the Web interface.

2. When the following dialog box appears, please enter the default user name and

password “admin” (or the password you have changed via console). The login

screen in Figure 6-2 appears.

Figure 6-2: Login Screen

3. After entering the password, the main screen appears as Figure 6-3 shows.

Default Username: admin

Default Password: admin

Otros manuales para GS-5220-8P2T2S

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cambiar de Planet

Planet

Planet FGSW-1820CS Manual de usuario

Planet

Planet KVM-U201 Manual de usuario

Planet

Planet ISW-500 Manual de usuario

Planet

Planet FSD-808P Manual de usuario

Planet

Planet IGSW-24040T Manual de usuario

Planet

Planet IGS-6325 Series Manual de usuario

Planet

Planet FNSW-2402 Manual de usuario

Planet

Planet FGSW-2612PVS Manual de usuario

Planet

Planet FNSW-1601 Manual de usuario

Planet

Planet IGS-6325 Series Manual de usuario

Planet

Planet MGSW-004-12F Manual de usuario

Planet

Planet FSD-804P Manual de usuario

Planet

Planet ISW-511 Series Manual de usuario

Planet

Planet IGS-4215 Series Manual de usuario

Planet

Planet WGSW-24000 Manual de usuario

Planet

Planet WGSD-10020 Manual de usuario

Planet

Planet IGS-6325-5X1T Manual de usuario

Planet

Planet FSD-808P Manual de usuario

Planet

Planet uh-400 Manual de usuario

Planet

Planet ISW-1022MT Manual de usuario

Planet

Planet IGS-624HPT Manual de usuario

Planet

Planet GSD-1603 Manual de usuario

Planet

Planet POE-1200 Manual de usuario

Planet

Planet GSW-1602SF Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario