Planet WGS-804HPT Manual de usuario
Industrial Wall-mount Managed Gigabit Ethernet Switch
WGS-804HPT/WGS-4215-8T/WGS-4215-8T2S
Quick Installation Guide
Table of Contents
1. Package Contents ....................................................................................... 3
2. Requirements ............................................................................................. 4
3. Wiring the Power Inputs.............................................................................. 5
3.1 Terminal Block Connector Pinout ........................................................... 6
4. Installation................................................................................................. 7
4.1 Wall Mount Installation......................................................................... 7
4.2 Magnet Installation .............................................................................. 8
4.3 DIN-rail Mount Installation ................................................................... 8
5. Starting Web Management .........................................................................10
6. SavingCongurationviatheWeb ...............................................................13
7. RecoveringBacktoDefaultConguration.....................................................14
8. Customer Support .....................................................................................15
3
1. Package Contents
Thank you for purchasing PLANET Industrial Wall-mount Managed Gigabit Switch,
WGS-804HPT / WGS-4215-8T / WGS-4215-8T2S.
The table below shows the models with the number of ports:
Model Name 10/100/1000T
Copper Ports
802.3at PoE
Ports
100/1000 SFP Fiber
Optical Interface
WGS-804HPT 8 4 —
WGS-4215-8T 8 — —
WGS-4215-8T2S 8 — 2
In the following section, unless specied, the term “Wall-mount Managed
Switch” mentioned in this quick installation guide refers to the WGS-804HPT /
WGS-4215-8T / WGS-4215-8T2S.
Open the box of the Wall-mount Managed Switch and carefully unpack it. The box
should contain the following items:
zThe Wall-mount Managed Switch x 1
zQuick Installation Guide x 1
z3-pin Terminal Block Connector x 1
zWall-mounted Kit x 1
zDIN-rail Kit x 1
zMagnet Kit x 1
zRJ45 Dust Cap x 8
zSFP Dust Cap x 2 (WGS-4215-8T2S only)
If any item is found missing or damaged, please contact your local reseller for
replacement.
4
2. Requirements
zWorkstations running Windows XP/2003/Vista/7/8/2008/10, MAC OS X or later,
Linux, UNIX, or other platforms are compatible with TCP/IP protocols.
zWorkstations are installed with Ethernet NIC (Network Interface Card)
zEthernet Port Connection
Network cables -- Use standard network (UTP) cables with RJ45 connectors.
The above PC is installed with Web browser and JAVA runtime environment
plug-in.
Note
It is recommended to use Internet Explore 8.0 or above to access
the Wall-mount Managed Switch. If the Web interface of the Wall-
mount Managed Switch is not accessible, please turn off the anti-
virus software or firewall and then try it again.
5
3. Wiring the Power Inputs
The Wall-mount Managed Switch features a strong dual power input system
(Terminal block and DC jack) incorporated into customer’s automation network to
enhance system reliability and uptime.
Power Input Range
Model
3-pin Terminal Block DC Jack
WGS-804HPT 48~56V DC 48~56V DC
WGS-4215-8T 12~48V DC, 24V AC 12~48V DC, 24V AC
WGS-4215-8T2S 12~48V DC, 24V AC 12~48V DC
10/100/1000BASE-T RJ45 Port
10/100/1000BASE-T RJ45 Port
3-pin Terminal Block
DC Plug-in
6
3.1 Terminal Block Connector Pinout
To install the 3-pin Terminal Block Connector on the Wall-mount Managed Switch,
simply follow the following steps:
Step 1: Insert positive DC power wire into V+, negative DC power wire into V-,
and grounding wire into Ground.
V+
V
-
Ground
Step 2: Tighten the wire-clamp screws for preventing the wires from loosening
and plug into the Wall-mount Managed switch.
Note
1. The wire gauge should be in the range from 12 to 24 AWG.
2. The device must be grounded.
7
4. Installation
4.1 Wall Mount Installation
To install the Wall-mount Managed Switch on the wall, simply follow the following
steps:
Step 1: There are 4 holes with 8mm diameter on the wall; the distance between
the 2 holes is 133mm(WGS-804HPT/WGS-4215-8T), 163mm(WGS-4215-
8T2S) and the line through them must be horizontal.
Step 2: Install a conductor pipe inside the board hole and ush the edge of the
conductor pipe with the wall surface.
Step 3: Screw the bolts into the conductor pipe. The Wall-mount Managed Switch
is between bolts and conductor pipe, as shown below.
8
4.2 Magnet Installation
To install the Wall-mount Managed Switch on a magnetic surface, simply follow the
following diagram:
4.3 DIN-rail Mount Installation
The DIN-rail kit is included in the package. When the wall-mount application for
the Wall-mount Managed Switch needs to be replaced with DIN-rail application,
please refer to the following gures to screw the DIN-rail on the Wall-mount
Managed Switch. To hang up the Wall-mount Managed Switch, follow the steps
below:
Step 1: Screw the DIN-rail on the Wall-mount Managed Switch
9
Step 2: Lightly insert the button of DIN-rail into the track
1Push
2Click
Step 3: Check whether the DIN-rail is tightly on the track
10
5. Starting Web Management
The following shows how to start up the Web Management of the Wall-mount
Managed Switch. Note the Wall-mount Managed Switch is congured through an
Ethernet connection. Please make sure the manager PC must be set to the same
IP subnet address.
For example, the default IP address of the Wall-mount Managed Switch is
192.168.0.100; then the manager PC should be set at 192.168.0.x (where
x is a number between 1 and 254, except 100) and the default subnet mask is
255.255.255.0.
PC / Workstation
with Web Browser
192.168.0.x
Managed Switch
RJ45/UTP Cable
IP Address:
192.168.0.100
Figure 5-1: IP Management Diagram
Otros manuales para WGS-804HPT
1
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Enrutador de red de Planet
Planet
Planet IGS-801T Manual de usuario
Planet
Planet MGSW-28240F Manual de usuario
Planet
Planet MGSW-28240F Manual de usuario
Planet
Planet VIP-462DG Manual de usuario
Planet
Planet FWA-2100-NR Manual de usuario
Planet
Planet ADSL Firewall Router ADE-4120 Manual de usuario
Planet
Planet FGSW-4840S Manual de usuario
Planet
Planet XRT-101A Manual de usuario
Planet
Planet WGS3-24000 Manual de usuario
Planet
Planet ADE-3400 Manual de usuario
Planet
Planet ADE-3400 Manual de usuario
Planet
Planet Powerline Ethernet Bridge PL-104E Manual de usuario
Planet
Planet FGSW-2620VM Series Manual de usuario
Planet
Planet XRT-401D Manual de usuario
Planet
Planet XRT-401F Manual de usuario
Planet
Planet FGSW-2620VM Series Manual de usuario
Planet
Planet WNRT-617 Manual de usuario
Planet
Planet FGSW-4840S Manual de usuario
Planet
Planet VC-230 Manual de usuario
Planet
Planet ADSL 2/2+ VPN Firewall Router ADE-4300A/B Manual de usuario
Manuales populares de Enrutador de red de otras marcas
NETGEAR
NETGEAR FS526T - Switch Manual de usuario
Korenix
Korenix JetNet 5710G Series Manual de usuario
Automated Logic
Automated Logic ZN551 Manual del propietario
Cisco
Cisco ASR 1000 Series Manual del operador
EnGenius
EnGenius ESR-9710 Manual de usuario
Cisco
Cisco 805 Series Instrucciones de funcionamiento y seguridad