Planet GRT-101 Manual de usuario

G.SHDSL Bridge Router

GRT-101/GRT-401/GRT-402

Quick Installation Guide

Table of Contents

Chapter 1 Before Starting Up............................................................................ 3

Chapter 2 Quick Installation ............................................................................. 4

2.1 Bridge Mode ............................................................................. 4

2.2 Routing Mode for PPPoA and PPPoE with IP Sharing ..................... 6

2.3 Routing Mode for IPoA or EoA .................................................... 9

2.4 LAN-to-LAN Connection with Bridge Mode...................................13

Chapter 1 Before Starting Up

Before proceeding any further, please make sure correct Ethernet cable is used

for connecting the LAN port of your computer to GRT-101/401/402. The LAN LNK

indicator on the front panel will light up if a correct cable is used.

By default, the GRT-101/401/402 is shipped with its DHCP Server function enabled.

This means the client computers on the LAN network including the Administrator

PC can set their TCP/IP settings to automatically obtain an IP address from the

GRT-101/401/402.

■Start your web browser and type http://192.168.0.1 in the browser’s address

box, and wait for the login screen appears. The default user name and pass-

word are “root”. Click OK button and you will login the management of

GRT-101/401/402.

Note

The factory default management IP and subnet mask of GRT-

101/401/402 is 192.168.0.1 and 255.255.255.0 respectively. And

the default user name and password are “root”.

This quick installation guide is intended to help to install the G.SHDSL Bridge

Router to the network through the management interface. For more detailed

settings, please also refer to the user’s manual.

Chapter 2 Quick Installation

This chapter provides quick setup procedures for four major connection modes:

Section 2.1: Bridge Mode

Section 2.2: Routing Mode for PPPoA and PPPoE

Section 2.3: Routing Mode for IPoA or EoA

Section 2.4: LAN to LAN Bridge Mode

Please verify your connection mode and check the corresponding section to quickly

install your GRT-101/401/402.

2.1 Bridge Mode

GRT-101

LAN IP 192.168.0.1

Mask 255.255.255.0

IP 192.168.0.31

Mask 255.255.255.0

Gateway 192.168.0.254

VPI = 0, VCI = 32

Encapsulation = LLC

BAS

IP 192.168.0.254

DSLAM

Bridge Mode

ISP

Web UI Conguration

After connection via web browser, click and to set up Bridging

mode of GRT-101/401/402 and then click for the next setting.

1. Enter WAN1 VPI: 0and VCI: 32.

2. Select WAN1 AAL5 Encap:

3. Enter LAN IP: 192.168.0.1

4. Enter LAN Sub-net Mask: 255.255.255.0

5. Enter Gateway: 192.168.0.254

The Gateway is directly pointed to the BAS IP.

6. Enter DNS Server : 168.95.1.1 and 168.95.192.1

7. Click

8.The screen will prompt the new congured parameters. Check the parameters

and click

. The router will reboot with the new setting or click

tocongureotherparameters.

Console Conguration

Do the following steps:

1. User: admin password: admin 

2. enable supervisor password: root 

3. setup mode Bridge 

4. wan Interface number (1~8): 1 

Protocol : Ethernet 

vpi_vci: 0 

32 

encap: LLC 

5. bridge gateway 192.168.0.254 

6. lan Interface number: 1 

7 address 192.168.0.1 

255.255.255.0 

8. (back to root) write y 

y (reboot)

2.2 Routing Mode for PPPoA and PPPoE with IP Sharing

GRT-101

LAN IP 192.168.0.1

Mask 255.255.255.0

IP 192.168.0.2

Mask 255.255.255.0

Gateway 192.168.0.1

DNS 192.168.0.1

VPI = 0, VCI = 32

Encapsulation = LLC

BAS

DSLAM

Router Mode

usrname: user1@net

password: user

ISP

WANLAN

Web UI Conguration

For Route Mode with Point-to-Point Protocol over ATM and Ethernet, follow the

following settings. First select and

, and then click for

setting other parameters.

1. Enter LAN IP: 192.168.0.1

2. Enter LAN Sub-net Mask: 255.255.255.0

3. Host Name: SOHO

4. DHCP Server: Enable

5. Click

6. Enter DHCP Client Start IP: 192.168.0.2

7. Enter DHCP Client End IP: 192.168.0.51

8. Enter DNS Server: 192.168.0.1

9. The DNS server is embedded in GRT-101/401/402.

10.Click to write the new setting.

11.Enter WAN1 VPI: 0and VCI: 32.

12.Select WAN1 AAL5 Encap:

13.Select: or

14.Click

15.Enter User Name provided by ISP: user1@net

16.Enter Password provided by ISP: user1

17.Re-enterPasswordforconrmation:user1

18.The screen will prompt the new congured parameters. Check the param-

eters and click

. The router will reboot with the new setting or click

tocongureotherparameters.

Console Conguration

Do the following steps:

1. User: admin password: admin 

2. enable supervisor password: root 

3. setup mode Route 

4. wan Interface number (1~8): 1 

protocol PPPoA or PPPoE 

vpi_vci: 0 

32 

encap LLC 

isp account: user1@net 

password: user1 

Idle timeout (ENTER for default) <10>: 10

5. lan Interface number: 1 

6. address 192.168.0.1 

255.255.255.0 

attrib Virtual 

7. (back to root) write y 

y (reboot)

2.3 Routing Mode for IPoA or EoA

LAN IP 192.168.0.1

Mask 255.255.255.0

IP 192.168.0.2

Mask 255.255.255.0

Gateway 192.168.0.1

VPI = 0, VCI = 32

Encapsulation = LLC

BAS

DSLAM

ISP

WANLAN

GRT-101

Router Mode

WNA IP 10.1.2.1

Mask 255.255.255.0

Gateway 10.1.2.2

DNS 168.95.1.1

IP 10.1.2.2

Mask 255.255.255.0

Web UI Conguration

For Route Mode with Classical IP over ATM and Ethernet over ATM, follow the

following settings. First select and

, and then click for

setting other parameters.

1. Enter LAN IP: 192.168.0.1

2. Enter LAN Sub-net Mask: 255.255.255.0

3. Host Name: SOHO

4. DHCP Server: Enable

5. Click

Otros manuales para GRT-101

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Enrutador de red de Planet

Planet

Planet VR-300 Series Manual de usuario

Planet

Planet XRT-401C Manual de usuario

Planet

Planet VC-23 Series Manual de usuario

Planet

Planet WDAP-C7210E Manual de usuario

Planet

Planet WGS3-24000 Manual de usuario

Planet

Planet WRT-403 Manual de usuario

Planet

Planet 85M Powerline Ethernet PL-201-UK/US Manual de usuario

Planet

Planet WGSW-2620PV Manual de usuario

Planet

Planet MGSW-28240F Manual de usuario

Planet

Planet ADE-4400 Manual de usuario

Planet

Planet FGSD-1022 Manual de usuario

Planet

Planet FGSW-2620VM Series Manual de usuario

Planet

Planet SOHOConnect Series Manual de usuario

Planet

Planet WGS-804HPT Manual de usuario

Planet

Planet AND-4102 Manual de usuario

Planet

Planet MGSW-2402 Manual de usuario

Planet

Planet ISW-802M Manual de usuario

Planet

Planet IGS-604HPT-M12 Manual de usuario

Planet

Planet FGSW-1822VHP Manual de usuario

Planet

Planet ISW-800M Manual de usuario

Planet

Planet FWA-2100-NR Manual de usuario

Planet

Planet ADE-3400v3 Manual de usuario

Planet

Planet ERT-805 Manual de usuario

Planet

Planet FGSD-1022VHP Manual de usuario

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

Cisco

Cisco NCS 540 Manual

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

Cisco

Cisco ASR 1000 Series Manual del operador

EnGenius

EnGenius ESR-9710 Manual de usuario

Cisco

Cisco 805 Series Instrucciones de funcionamiento y seguridad