Planet ICA-151 Manual de usuario
Dual Mode CMOS Internet Camera
ICA-151
Version 1.1
Quick Installation Guide
Table of Contents
1. PACKAGE CONTENTS ................................................................................... 3
2. SYSTEM REQUIREMENTS .............................................................................. 4
3. OUTLOOK ................................................................................................ 5
3.1 Front Panel ......................................................................................... 5
3.2 Rear Panel .......................................................................................... 6
4. Physical Installation ..................................................................................... 7
5. Setup Wizard Conguration .......................................................................... 8
6. Cam Viewer Lite Installation ........................................................................15
Appendix A: Feature Listing for Cam Viewer......................................................19
Appendix B: Suggest Hardware / System Requirement ......................................20
Appendix C: Ordering Information for Cam Viewer Pro.......................................20
3
1. PACKAGE CONTENTS
1 x ICA-151
1 x Camera Stand
1 x Power Adapter
1 x CD-ROM
1 x Quick Installation Guide
Note
Please use the power adapter in this package. Using a power supply
with a different voltage rating will damage and void the warranty
for this product.
ó
ó
ó
ó
ó
4
2. SYSTEM REQUIREMENTS
Network Interface 10/100 Base-TX Ethernet
Monitoring System Recommended for Internet Explorer 6.0 or later
System Hardware
• CPU: Pentium 4, 1.5GHz or above
• Memory Size : 512 MB or above
• VGA card resolution : 1024 x 768 or above
• Network bandwidth: In VGA resolution mode,
minimum upload bandwidth is 1Mbps.
Optional:
• Sound Card
• Microphone (for PC)
• Speaker (for PC and ICA-151)
5
3. OUTLOOK
3.1 Front Panel
Microphone
PWR LAN
ACT
LED Status LED Description
PWR
Off No power.
On Power on.
Blinking The Power LED will blink during start up (15 ~ 20 sec).
ACT Off Camera is not capturing video.
Blinking Camera is capturing video.
LAN Off LAN is not connected or camera is not sending/receiving data.
Blinking Data is being transmitted or received via the LAN connection.
6
3.2 Rear Panel
AUDIO OUT PWR LAN
PORT PORT Description
AUDIO OUT An external speaker can be plugged in.
PWR Connect the supplied power adapter.
LAN Connect your Camera to a 10/100Base-TX hub or switch.
Reset
Reset to manufacturer default valued and reboot.
When pressed and held over 10 seconds, the settings of IP
Camera will be set to the default values.
Upon completion, the PWE LED will blink three times.
Bottom Panel of ICA-151
7
4. Physical Installation
1. Connect an Ethernet cable
Connect one end of an Ethernet cable to the LAN port located on the IP camera’s
rear panel and connect the other end to the network device (hub or switch).
2. Attach the external power supply
Attach the provided power adapter to the IP camera’s connector labeled “PWR”
on the rear panel.
3. Check the LEDs
a. The Power LED will turn on briey, and then start blinking during startup.
After startup is completed, the Power LED will remain ON.
b. The LAN LED will be ON.
8
5. Setup Wizard Conguration
Initial setup should be performed by using the supplied Windows-based Setup
Wizard as follows:
1. Insert the bundled Product CD disk into CD-ROM drive to launch the autorun
program.
2. After the web page displayed, click the “Setup Wizard” hyperlink on the list to
start the conguration process.
Note
If the web page does not appear, click “Start” on the task bar and
select “Run” to type “X:\Utility\SetupWizard\SetupWizard.
exe”, assume X is your CD-Rom drive.
3. The welcome screen appears. Click on “Setup Camera” button to start the
wizard.
9
4. After clicking the setup camera button, it will auto search for the IP Cameras on
your network. Click on to continue.
5. The next screen below will list the IP Camera on your network. Select it from
the list on the left side, the current settings table will be displayed on the right
side. Click on to continue.
10
6. The administrator login window will pop up. If the Administrator Name and
Administrator Password have been set, you will be prompted to enter them. If
using the default values, please enter “admin” for both the name and the pass-
word. Click on “OK” to continue.
7. On the following Camera Settings screen, you can ll and congure the Device
Name, Description, Time Zone, Local Date and time here. Click on to
continue.
Otros manuales para ICA-151
3
Tabla de contenidos
Otros manuales de Cámara IP de Planet
Planet
Planet ICA-3350P Manual de usuario
Planet
Planet ICA-HM132 Manual de usuario
Planet
Planet ICA-4500V Manual de usuario
Planet
Planet ICA-100C Manual de usuario
Planet
Planet ICA-350 Manual de usuario
Planet
Planet ICA-HM100 Manual de usuario
Planet
Planet ICA-HM830W Manual de usuario
Planet
Planet ICA-151 Manual de usuario
Planet
Planet ICA-W8100 Manual de usuario
Planet
Planet ICA-601 Manual de usuario
Planet
Planet ICA-HM120 Manual de usuario
Planet
Planet ICA-HM136 Manual de usuario
Planet
Planet ICA-100 Manual de usuario
Planet
Planet ICA-107P Manual de usuario
Planet
Planet ICA-W7100 Manual de usuario
Planet
Planet ICA-3260 Manual de usuario
Planet
Planet ICA-5250V Manual de usuario
Planet
Planet ICA-W7100 Manual de usuario
Planet
Planet ICA-525 Manual de usuario
Planet
Planet ICA-2000 Series Manual de usuario
