PLANEPRINT WANNA PLAY II Manual de programación

PRINTING & ASSEMBLING MANUAL

NOTE:

Slicing works best

with CURA!

www.planeprint.com

the ONLY place where you can get

original Planeprint STL ﬁles legally!

Reno Air race biplane

WANNA PLAY II 2

PRINTING & ASSEMBLING MANUAL

PLALW-PLA TPU CARBON

WANNA PLAY II 3

PRINTING & ASSEMBLING MANUAL

Required accessoires

Filament

• LW-PLA (cannot be replaced by PLA!), ~1500 grams

• PLA oder better Tough PLA, ~320 grams

• TPU A95, ~20 grams

• LW-TPU Colorfabb VarioShore about 100 grams

(strongly recommended for tires, but it also works with normal TPU)

Materials

• some tapping screws

(search for: M2 ﬂat head tapping screw assortment)

• CA super glue (liquid and liquid medium)

• CA activator

• Metal screw 3*40mm with nuts (not self-locking!), 4 pieces

• Metal screw 3*20mm with self-locking nuts, 4 pieces

• Metal screw 3*30mm, 2 pieces

• Ball bearings 3x6x2,5mm, 4 pieces

• Carbon tube Ø8mm*1000mm (inside 6mm), 4 pieces*

• Carbon rod Ø3*1000mm, 1 piece*

• Steel wire Ø1*1000mm, 2 pieces

• Self-adhesive Velcro tape

• Velcro strap

• Servo cable extension 350mm, 2 pieces

• Rod connection, 4 pieces

• Neodym-Super-Magnet 5x5x5mm, 4 pieces

• some Hair gums

• some lead to correct the CG

Tools

Cutter knife, small Philips screwdriver, Sandpaper,

Metal saw, Needle nose pliers.

*Cut the 8mm tubes into the following parts:

Tube 1 for the gear: 2x125, 2x158

Tube 2 for the wings: 2x500

Tube 3 for the wings and HS: 1x800, 1x120

Tube 4 for the wing: 1x1000 (do not cut)

*Cut the 3mm rod into the following parts:

Motormount: 4x200

Metal screw 3*40mm, 3*20

Rod connection

Carbon tube

Magnet 5x5x5mm

Tapping screws 2mm

Hair gums

Ball bearings

6 mm

3 2.5

WANNA PLAY II 4

PRINTING & ASSEMBLING MANUAL

RC Components

ENGINE PROPDRIVE V2 3548 900KV (HobbyKing) or comparable motors.

You can also use any other motor that ﬁts a 14x7 propeller!

NOTE Tthis motorization is very powerful. The Wanna Play is not

full throttle safe with it. Always be careful, it is up to your discretion

and the quality of your printing and assembly as to what stresses

the aircraft can withstand.

The optimal length of the motor is when the distance to the back of the prop is 58 mm.

If the motor is shorter, you can use longer screws and washers. If the motor is longer, the

motor cross can also be mounted behind the motor mount. In this case the diameter of the

motor must not be more than 35 mm!

PROP 12x7 or 14x6

BEC-CONTROLLER 80 A (must ﬁt the engine!)

RECEIVER 5 Channel

BATTERY 4S Lipo, 3500 – 5000 MaH

(The battery should have a weight of 400 to 450 grams)

SERVOS 4 pieces like Corona DS-238MG or comparable

Dimensions (The optimal distance between screws is 35 mm):

max. 30 mm max. 15 mm

max. 30 mm

43 to 50 mm

58 mm

Rear mounting Prop

WANNA PLAY II

PRINTING & ASSEMBLING MANUAL

Printing the parts – Printing proﬁles

For the new PROFILE P5_Gyroid it is essential to use Cura Version 5 or later, It will work with

older versions, but the weight of the parts will be higher and the printing time longer.

This manual is constantly being improved and supplemented, we recommend downloading

the latest version from our website before building.

The development of a complex, airworthy RC ﬂight model to express on any stan-

dard 3D printer is a very complex and extensive process. Therefore, we appeal to

your fairness not to forward the STL data you have acquired to third parties.

Thank you for your understanding and have fun with your PLANEPRINT MODEL!

Important for the

1-wall-print (P3, P5)!

In order to print airfoils of the lowest possi-

ble weight with high stability, it is necessa-

ry to print with only one wall line (Nozzle 0.4

mm). Decisive here is the adhesion between

the layers! To achieve this, you must print at

a much higher temperature than normal. As

a guideline, 230° C is a good starting point.

The parts-cooling fan should be set to 0% or

a maximum of 20%. Since not every printer

works the same, it may be necessary to make

small adjustments to these settings.

For slicing all Planeprint

models, these proﬁles have

to be created in Cura:

PROFILE P1_Fullbody

PROFILE P2_Hollowbody

PROFILE P3_Surface (Not necessary for this plane)

PROFILE P4_Flex

PROFILE P5_Gyroid

You can ﬁnd the description at

www.planeprint.com/print

PROFILE P5_Gyroid

It is essential for the necessary stability of the LW parts

printed with PROFILE_5 are as stable as possible. Please

use a test part to check the strength by fracture tests. It must

not break along the layer lines under any circumstances! Also

note that the printing temperature for LW-PLA is as low as

possible to obtain a wall thickness of 0.4 to 0.6 mm at a ﬂow

of 60 to 70 % (depending on brand).

Caution: at too high temperatures, LW-PLA becomes brittle

and breaks more easily.

WANNA PLAY II

PRINTING & ASSEMBLING MANUAL

P1_Interconnects_wp.stl

MATERIAL PLA, Weight: ~ 3 g

ADDITIONAL SETTINGS

None required

PROFILE P1_Fullbody PLA or Tough PLA

The following parts must be sliced with the PROFILE P1_Fullbody.

Please note the additional settings for the individual parts!

P1_Gear parts_wp.stl

MATERIAL PLA, Weight: ~ 45 g

ADDITIONAL SETTINGS

None required

WANNA PLAY II

PRINTING & ASSEMBLING MANUAL

P1_Motormount_wp.stl

MATERIAL PLA, Weight: ~ 18 g

ADDITIONAL SETTINGS

None required

PROFILE P1_Fullbody PLA or Tough PLA

The following parts must be sliced with the PROFILE P1_Fullbody.

Please note the additional settings for the individual parts!

P1_Motormount base_wp.stl

MATERIAL PLA, Weight: ~ 21 g

ADDITIONAL SETTINGS

None required

WANNA PLAY II

PRINTING & ASSEMBLING MANUAL

P1_Protectors FUS_wp.stl

MATERIAL PLA, Weight: ~ 11 g

ADDITIONAL SETTINGS

None required

PROFILE P1_Fullbody PLA or Tough PLA

The following parts must be sliced with the PROFILE P1_Fullbody.

Please note the additional settings for the individual parts!

P1_Parts_wp.stl

MATERIAL PLA, Weight: ~ 19 g

ADDITIONAL SETTINGS

None required

WANNA PLAY II 9

PRINTING & ASSEMBLING MANUAL

P1_Parts rear_wp.stl

MATERIAL PLA, Weight: ~ 9 g

ADDITIONAL SETTINGS

None required

PROFILE P1_Fullbody PLA or Tough PLA

The following parts must be sliced with the PROFILE P1_Fullbody.

Please note the additional settings for the individual parts!

P1_Protectors WING_wp.stl

MATERIAL PLA, Weight: ~ 11 g

ADDITIONAL SETTINGS

None required

Remove support.

Please be careful with the knife!

WANNA PLAY II

PRINTING & ASSEMBLING MANUAL

P1_Servo board 35mm_wp.stl or

P1_Servo board customizable_wp.stl

MATERIAL PLA, Weight: ~ 5 g

ADDITIONAL SETTINGS

None required

PROFILE P1_Fullbody PLA or Tough PLA

The following parts must be sliced with the PROFILE P1_Fullbody.

Please note the additional settings for the individual parts!

P1_Rear gear_wp.stl

MATERIAL PLA, Weight: ~ 4 g

ADDITIONAL SETTINGS

None required

Tabla de contenidos

Otros manuales de Juguete de PLANEPRINT

PLANEPRINT

PLANEPRINT Abrams P-1 Explorer Manual de usuario

PLANEPRINT

PLANEPRINT JETWING Manual de usuario

PLANEPRINT

PLANEPRINT SEAGULL GLIDER VERSION Manual de usuario

PLANEPRINT

PLANEPRINT EAGLE Manual de usuario

PLANEPRINT

PLANEPRINT FOUGA MAGISTER Manual de programación

PLANEPRINT

PLANEPRINT ZIGGY Manual de programación

PLANEPRINT

PLANEPRINT Foka 4 Instrucciones de uso

PLANEPRINT

PLANEPRINT paper plane Manual de usuario

PLANEPRINT

PLANEPRINT Funbus Manual de usuario

PLANEPRINT

PLANEPRINT AERON Manual de programación

PLANEPRINT

PLANEPRINT BLERIOT XI Manual de programación

PLANEPRINT

PLANEPRINT Slingsby T31 Cadet Manual de programación

PLANEPRINT

PLANEPRINT SHARD Manual de programación

PLANEPRINT

PLANEPRINT BIG BOBBER Manual de usuario

PLANEPRINT

PLANEPRINT NOTOS Manual de usuario

PLANEPRINT

PLANEPRINT FEARLESS Manual de programación

PLANEPRINT

PLANEPRINT Swift S1 Manual de programación

PLANEPRINT

PLANEPRINT V-TURN Manual de usuario

PLANEPRINT

PLANEPRINT RISE Manual de usuario

PLANEPRINT

PLANEPRINT ZLIN SAVAGE BOBBER Manual de usuario

PLANEPRINT

PLANEPRINT OV10 Bronco Manual de programación

PLANEPRINT

PLANEPRINT Aermacchi MB-339 Manual de usuario

Manuales populares de Juguete de otras marcas

marklin

marklin 37321 Manual de usuario

Canon

Canon PAPER CRAFT Manual de usuario

GREAT PLANES

GREAT PLANES Pitts M-12S Manual de usuario

NOCH

NOCH 14261 Manual de usuario

Hausler

Hausler 450 SE V2 Manual de usuario

Dynaflite

Dynaflite Daydream Manual de usuario

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Manual

Kenner

Kenner Batman 63651 Manual de usuario

LEGO

LEGO 8527 Manual de usuario

iKarus

iKarus ECO 8 Manual de usuario

Multiplex

Multiplex EasyStar II Manual de instrucciones

Walkera

Walkera 38 Manual de instrucciones

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Manual de usuario

MD MXION SWD Manual de usuario

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Manual de usuario

marklin

marklin 39671 Manual de usuario

Meccano

Meccano 15103 Manual de usuario

LEGO

LEGO TECHNIC 8735 Manual de usuario