PLANEPRINT paper plane Manual de usuario
PRINTING & ASSEMBLING MANUAL
NOTE:
Slicing works best
with CURA!
www.planeprint.com
the ONLY place where you can get
original Planeprint STL files legally!
PAPER PLANE 2
PRINTING & ASSEMBLING MANUAL
© PLANEPRINT
PLALW-PLA TPU
PLA
LW-PLA
TPU
PAPER PLANE 3
PRINTING & ASSEMBLING MANUAL
© PLANEPRINT
RC Components
MOTOR AXI 2203/40 VPP or comparable indoor-20 grams-motors.
31 mm
or comparable indoor-20 grams-motors.
PROP 8x3.8, 8x4.3 or comparable (not the soft indoor props)
BEC-CONTROLLER 15 A (one matching the motor)
RECEIVER 4 Channel
BATTERY 2S Lipo, 900 MaH (ideal weight 45 g, maximum thickness 18 mm, maximum height 30 mm)
SERVOS Hitec HS-55 or similar, 3 pieces
max. 23 mm max. 13 mm
max. 29 mm
Required accessoires – basic equipment
Links to recommended accessories can be found on
www.planeprint.com/paper (scroll down)
• LW-PLA (cannot be replaced by PLA!), ~220 grams
• PLA oder better Tough PLA, ~20 grams
• TPU A95, ~5 grams
• some tapping screws
• CA super glue (liquid and medium)
• CA activator
• Carbon rod Ø1.5*1000mm, 1 piece
• Rod connection 2mm, 6 pieces
• Self adhesive velcro tape
Tools
Cutter knife, small Philips screwdriver, Sandpaper,
Needle nose pliers
Rod connection hole 2mm
Tapping screws 2mm
PAPER PLANE
4
PRINTING & ASSEMBLING MANUAL
© PLANEPRINT
This manual is constantly being improved and supplemented, we recommend downloading
the latest version from our website before building.
To print all PLANEPRINT models you need to set some basic profiles in Cura (If you use another
slicer, please set the same parameters).
You can find the description at www.planeprint.com/print
For this model you need the following profiles:
Printing the parts – Printing profiles
The development of a complex, airworthy RC flight model to express on any stan-
dard 3D printer is a very extensive process. Therefore, we appeal to your fairness
not to forward the STL data you have acquired to third parties.
Thank you for your understanding and have fun with your PLANEPRINT MODEL!
PROFILE P5_Gyroid
It is essential for the necessary stability of the LW parts
printed with PROFILE_5 are as stable as possible. Please
use a test part to check the strength by fracture tests. It must
not break along the layer lines under any circumstances! Also
note that the printing temperature for LW-PLA is as low as
possible to obtain a wall thickness of 0.4 to 0.6 mm at a flow
of 60 to 70 % (depending on brand).
Caution: at too high temperatures, LW-PLA becomes
brittle and breaks more easily.
TPU LW-PLAPLA
PAPER PLANE 5
PRINTING & ASSEMBLING MANUAL
© PLANEPRINT
P1_Motor mount_pp.stl
MATERIAL PLA, Weight: ~ 5 g
ADDITIONAL SETTINGS
None required
PROFILE P1_Fullbody PLA or Tough PLA
The following parts should be sliced with the PROFILE P1_Fullbody.
Please note the additional settings for the individual parts!
P1_Interconnects_pp.stl
MATERIAL PLA, Weight: ~ 3 g
ADDITIONAL SETTINGS
None required
PAPER PLANE 6
PRINTING & ASSEMBLING MANUAL
© PLANEPRINT
P1_Servo mount_pp.stl
MATERIAL PLA, Weight: ~ 3 g
ADDITIONAL SETTINGS
None required
PROFILE P1_Fullbody PLA or Tough PLA
The following parts should be sliced with the PROFILE P1_Fullbody.
Please note the additional settings for the individual parts!
P1_Parts_pp.stl
MATERIAL PLA, Weight: ~ 2 g
ADDITIONAL SETTINGS
None required
PAPER PLANE 7
PRINTING & ASSEMBLING MANUAL
© PLANEPRINT
PROFILE P1_Fullbody PLA or Tough PLA
The following parts should be sliced with the PROFILE P1_Fullbody.
Please note the additional settings for the individual parts!
P1_Spinner_pp.stl
MATERIAL PLA, Weight: ~ 3 g
ADDITIONAL SETTINGS
None required
You can optionally use the spinner to increase
the tension of the rubber band for the prop.
Try which spinner fits better on your prop.
PAPER PLANE 8
PRINTING & ASSEMBLING MANUAL
© PLANEPRINT
PROFILE P4_Flex
The following parts should be sliced with the PROFILE P4_Flex.
Please note the additional settings for the individual parts!
P4_TPU-Parts_pp.stl
MATERIAL TPU A95, Weight: ~ 2 g
ADDITIONAL SETTINGS
• Infill Density: 100 %
PAPER PLANE 9
PRINTING & ASSEMBLING MANUAL
© PLANEPRINT
P5_Aileron L_pp.stl
MATERIAL LW-PLA, ~ 11 g*
*Weighed (approximate guideline)
ADDITIONAL SETTINGS
None required
P5_Aileron R_pp.stl
MATERIAL LW-PLA, ~ 11 g*
*Weighed (approximate guideline)
ADDITIONAL SETTINGS
None required
PROFILE P5_Gyroid Light-Weight LW-PLA!
The following parts must be sliced with the PROFILE P5_Gyroid. Please note the additional
settings for the individual parts! It is essential to print these parts with LW-PLA!
Basic settings for LW-PLA: Please follow the instructions in our WINGTEST AND CALIBRATION TOOL
on our website for correct adjustment!
PAPER PLANE 10
PRINTING & ASSEMBLING MANUAL
© PLANEPRINT
P5_Delta 1_pp.stl
MATERIAL LW-PLA, ~ 25 g*
*Weighed (approximate guideline)
ADDITIONAL SETTINGS
• Wall Line Count: 2
P5_Delta 2 L_pp.stl
MATERIAL LW-PLA, ~ 17 g*
*Weighed (approximate guideline)
ADDITIONAL SETTINGS
None required
Remove support.
Please be careful with the knife!
PROFILE P5_Gyroid Light-Weight LW-PLA!
The following parts must be sliced with the PROFILE P5_Gyroid. Please note the additional
settings for the individual parts! It is essential to print these parts with LW-PLA!
Basic settings for LW-PLA: Please follow the instructions in our WINGTEST AND CALIBRATION TOOL
on our website for correct adjustment!
Tabla de contenidos
Otros manuales de Juguete de PLANEPRINT
PLANEPRINT
PLANEPRINT ZIGGY Manual de programación
PLANEPRINT
PLANEPRINT V-TURN Manual de usuario
PLANEPRINT
PLANEPRINT EAGLE Manual de usuario
PLANEPRINT
PLANEPRINT NOTOS Manual de usuario
PLANEPRINT
PLANEPRINT Swift S1 Manual de programación
PLANEPRINT
PLANEPRINT SHARD Manual de programación
PLANEPRINT
PLANEPRINT ZLIN SAVAGE BOBBER Manual de usuario
PLANEPRINT
PLANEPRINT JETWING Manual de usuario
PLANEPRINT
PLANEPRINT RISE Manual de usuario
PLANEPRINT
PLANEPRINT WANNA PLAY II Manual de programación
PLANEPRINT
PLANEPRINT Funbus Manual de usuario
PLANEPRINT
PLANEPRINT Slingsby T31 Cadet Manual de programación
PLANEPRINT
PLANEPRINT FOUGA MAGISTER Manual de programación
PLANEPRINT
PLANEPRINT Abrams P-1 Explorer Manual de usuario
PLANEPRINT
PLANEPRINT BIG BOBBER Manual de usuario
PLANEPRINT
PLANEPRINT OV10 Bronco Manual de programación
PLANEPRINT
PLANEPRINT SEAGULL GLIDER VERSION Manual de usuario
PLANEPRINT
PLANEPRINT FEARLESS Manual de programación
PLANEPRINT
PLANEPRINT Foka 4 Instrucciones de uso
PLANEPRINT
PLANEPRINT Aermacchi MB-339 Manual de usuario
