Pintek DP-35 Manual de usuario



35MHz/1600Vp‐p



INSTRUCTION MANUAL

使用說明書



HIGH VOLTAGE DIFFERENTIAL PROBE

差動測試棒

DP-35

2



TABLEOFCONTENTS



FEATURES--------------------------------------------------------------- 5

SPECIFICATIONS-------------------------------------------------------- 5

PANEL DESCRIPTION------------------------------------------------------6

OPERATING ENVIRONMENTAL CONDITIONS----------------7

OPERATING PROCEDURE------------------------------------------7

EXT. POWER SOURMAINTENANCE-----------------------------------9

CLEANING------------------------------------------------------------------------9

WARRANTY--------------------------------------------------------------------9

REPAIR-------------------------------------------------------------------------9

DERATING CURVE-----------------------------------------------------10



簡述-----------------------------------------------------------------14

規格--------------------------------------------------------------14

測試棒面板說明-------------------------------------------------------15

操作環境及狀況-------------------------------------------------------------16

操作程序----------------------------------------------------------------------16

外接電源------------------------------------------------------------------------18

清潔----------------------------------------------------------------------------18

保固-------------------------------------------------------------------------------18

維修-------------------------------------------------------------------------------18

高頻耐電壓曲線參考圖----------------------------------------19

4



DP-35

HIGH VOLTAGE DIFFERENTIAL PROBE



5

DifferentialVoltageProbe,

Read the instructions before using the instrument:

1. Must acquire a differential voltage probe & get the best service from

instrument.

2. Read carefully the USER MANUAL.

3. Respect the safety precautions.

SAFETYPRECAUTIONS

Warning, Risk of Electric Shock,

Respectthemaxinputvoltages.

1. Max differential voltage: 1600 V (DC + AC peak) or 560V RMS

2. Max voltage between each input terminal and ground: 600 V RM



Donotusetheprobeindampenvironmentorwherethereis

riskofexplosion.

Donotusetheprobewithitscaseopen.

Disconnecttheinputsandoutputsoftheprobebefore

openingthecase.



TOORDERDifferentialVoltageProbeandAccessories:

An Insulated BNC/BNC lead and two Ф4 mm, length 3 inches(BP-250).

Supplied an Adapter preset 5 V / 2 A DC (100~240 V : ASW-01)

2 x high voltage IC clips (BP-256N).

2 x Banana to Banana high voltage plug (BP-356N).

2 x Alligator plug (BP-276N).

Instruction Manual.



6

FEATURES:

The DP-35 differential voltage probe provides a safety means of

measuring floating potentials for all models of oscilloscopes incomplete

safety.

It converts the high differential voltage (≦1600 peak) into a low

voltage (≦8.0 V) with reference to the earth for display on the

oscilloscopes.

The BNC output is designed to operate on an input with an impedance

of 1 MΩ. It is 2 times of the 50 Ω.

Recommend to use PINTEK PL-10 with DP-35, and expand the

measuring ranges. From DMM can observe more exact measured

testing voltage. (Oscilloscope accuracy is 3%, and DMM is 10 times).

DP-35 is a design for high sensitivity module and high dynamic range.

Attenuation x10, x100 is multiple of 10, which is easy for calculation

without mistake. Maximum voltage is 1600Vp-p. It is for high sensitivity

as well as for high voltage.

SPECIFICATIONS:

(1) Bandwidth: DC - to 35 MHz

(2) Attenuation: x 10, or x 100

(3) Accuracy: 2%

(4) Voltage Input Ranges (DC + AC peak to peak):

≦160 Vp-p for x 10, (i.e about 56 V RMS or 80 V DC)

≦1600 Vp-p for x 100, (i.e about 560 V RMS or 800 V DC)

(5) Permitted Max Input Voltage

Max differential voltage: 1600V (DC + AC peak to peak)

Max voltage between each input terminal and ground: 600 V RMS

(6) Input Impedance:

Differential: 8 MΩ// 2.5 pF

Between terminals and ground: 4 MΩ// 5 pF

(7) Output: ≦8.0 V

7

(8) Output Impedance: 50 Ω

(9) Rise Time: 10 ns

(10) Rejection Rate on Common Mode:

60 Hz: ＞80 dB ; 100 Hz: ＞60 dB ; 1 MHz: ＞50 dB

(11) Power Supply:

External 5V DC power supply.

(12) Consumption: 300 mA about [ 5 V / 2 A DC(100~240V : ASW-01) ]

PANEL DESCRIPTION:



8

OPERATING ENVIRONMENTAL CONDITIONS:

Reference Use Storage

Temperature +20°C …+30°C 0°C …+50°C -30°C …+70°C

Relative

Humidity ≦70 % RH 10 % … 85 % RH 10 % …90 % RH

(1) Dimensions and Weight:

195 x 55 x 30 mm; 250g

(2) Electrical Safety to IEC 1010-1:

Dual Insulation

Installation Category III

Degree of Pollution 2

Rated Voltage or Max Live-Earth: 600 V RMS

(3) CE Mark:

Conforms to EN 50081-1 and 50082-1 standards

OPERATING PROCEDURE:

Connect to leads to the input and place the wire-grip on the circuit to be

tested.

Connect the probe to the oscilloscope with the insulated BNC/BNC

lead.

Adjust the vertical zero adjustment of the oscilloscope if necessary.

Select the attenuation ratio* and the vertical deviation of the

oscilloscope in accordance with the conversion table below.

NB: The POWER light must come on.

The conversion table gives the real vertical deviation.

Attenuation x 100 x 10

MAX Voltage Input Range(DC+AC Peak) 1600 V 160 V

DC MAX INPUT ±800 V ±80 V

AC RMS MAX INPUT 560 V 56 V

9



Vertical Deviation

on the Oscilloscope

in V/div

Real Deviation In V/div

x 100 Range x 10 Range

1 100 10

0.5 50 5

0.2 20 2

0.1 10 1

50 m 5 0.5

20 m 2 0.2

10 m 1 0.1

5 m 0.5 50 m

2 m 0.2 20 m

[NOTE]

The real vertical deviation in V/div is equal to the attenuation factor

multiplied by the range of vertical deviation selected on the

oscilloscope. It will be doubled in the case of use of a 50 Ωload.

Example:

With the probe on factor x100, the oscilloscope on 0.5 V/div, the real

vertical deviation is 100 x 0.5 = 50 V/div.

With a 50Ωload on the input of the oscilloscope the deviation becomes

100 V/div.

10

EXT. POWER SOURCE:

Power consumption of the probe is about 300mA (ASW-01), thus it not

suit for battery, please use the accessory adapter only.

If there are any damage on the adaptor, please contact us and use the

adaptor supply by us only. If the input power over 9V DC will caused to

the probe hard damage.

MAINTENANCE:

For maintenance, only use specified spare parts.

The manufacturer can not be held responsible for any accident arising

following a repair made other than it’s after sales service or approved

repairers.

CLEANING:

This probe does not require any particular cleaning. If necessary, clean the

case with a cloth slightly moistened with soapy water.

WARRANTY:

Unless notified to the contrary, our instruments are guaranteed against any

manufacturing defect or material defect. They do not bear the specification

known as the safety specification. Our guarantee, which may not under any

circumstances exceed the amount of the invoiced price, goes no further

than the repair of our faulty equipment, carriage paid to our workshops.

REPAIR:

Maintenance, repairs under or out of guarantee. Please return to product to

your distributor.

11

DERATING CURVE:

The derating curve of the absolute maximum input voltage in common

mode is show as follows:

Tabla de contenidos

Otros manuales de Instrumento de medición de Pintek

Pintek

Pintek HVP-18HF Manual de usuario

Pintek

Pintek PA-677 Manual de usuario

Pintek

Pintek HVP-40M Manual de usuario

Pintek

Pintek hvp-40 Manual de usuario

Pintek

Pintek DP-60HS Manual de usuario

Pintek

Pintek DP-25 Manual de usuario

Pintek

Pintek PA-699 Manual de usuario

Pintek

Pintek DP-5205A Manual de usuario

Pintek

Pintek HVP-40 Manual de usuario

Pintek

Pintek DP-65 pro Manual de usuario

Pintek

Pintek DP-16VF Manual de usuario

Pintek

Pintek PA-659 Manual de usuario

Pintek

Pintek DP-16K Series Manual de usuario

Pintek

Pintek DP-15K Manual de usuario

Pintek

Pintek HVP-10R Manual de usuario

Pintek

Pintek DP-800HS Manual de usuario

Pintek

Pintek PA-622 Manual de usuario

Pintek

Pintek DP-30K Manual de usuario

Pintek

Pintek PA-629 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario