PiiGAB 810 Manual de usuario
www.piigab.com
PiiGAB Processinformation i Göteborg AB • Anders Carlssons gata 7 • S-417 55 Göteborg • Sweden
Tel: +46(0)31 559977 • Fax: +46(0)31 227071 • email: inf[email protected]e
Getting started PiiGAB 810
Getting started PiiGAB 810 Rev 1.00.01
© PiiGAB Processinformation i Göteborg AB Page: 2
Contents
1. DOCUMENT INFORMATION ............................................................................................ 3
1.1 VERSIONS..................................................................................................................... 3
2. REQUIREMENTS............................................................................................................... 3
2.1 OPTIONAL REQUIREMENTS............................................................................................. 3
3. INSTALLATION AND CONNECTIONS ............................................................................ 4
4. PIIGAB 810’S MAC-ADDRESS......................................................................................... 5
5. IP-CONFIGURATION ........................................................................................................ 5
5.1 DHCP NETWORK........................................................................................................... 5
5.2 STATIC IP ..................................................................................................................... 5
6. FIND YOUR PIIGAB 810 ON YOUR NETWORK.............................................................. 8
7. CONFIGURE THE PIIGAB 810......................................................................................... 9
8. PIIGAB M-BUS SETUP WIZARD –M-BUS COMMUNICATION ................................... 11
8.1 COMMUNICATE WITH TEST AND DIAGNOSTIC ADDRESS................................................... 12
8.2 COMMUNICATE WITH THE METER’S ACTUAL PRIMARY ADDRESS ...................................... 13
8.3 IDENTIFY THE METER’S ADDRESSES IN THE PIIGAB M-BUS SETUP WIZARD.................... 14
8.4 PARTS IN THE SECONDARY ADDRESS............................................................................ 14
8.5 SECONDARY ADDRESS –IDENTIFICATION NUMBER AND WILD CARDS............................... 15
8.6 ENTIRE SECONDARY ADDRESS ..................................................................................... 15
8.7 WILD CARD WITH SECONDARY ADDRESS ....................................................................... 16
9. APPENDIX ....................................................................................................................... 17
9.1 CONTACTS.................................................................................................................. 17
Getting started PiiGAB 810 Rev 1.00.01
© PiiGAB Processinformation i Göteborg AB Page: 3
1. Document Information
This document will describe how to configure the PiiGAB 810 for M-Bus communication with
one M-Bus meter using static IP or DHCP.
If you see something that is not correct in this document, that misleads you or if you are
missing something please contact us so we can improve this document continuously. See
contact information at the end of the document.
1.1 Versions
Version
Modified by
Details
1.00.00
Stefan Eriksson
Initial version
1.00.01
Stefan Eriksson
Edited distributor contact information
2. Requirements
Object
Detail
One PiiGAB 810
One M-Bus meter
Supports EN13757
One power supply
24V AC/DC
A patch cable
PiiGAB M-Bus Setup Wizard
Version 3.1.0 or later
2.1 Optional requirements
Object
Detail
A local area network (LAN)
With DHCP
One network switch
Getting started PiiGAB 810 Rev 1.00.01
© PiiGAB Processinformation i Göteborg AB Page: 4
3. Installation and connections
1. Install PiiGAB M-Bus Setup Wizard
2. Connect PiiGAB 810 gateway to your computer with the patch cable
3. Connect the M-Bus meter to the PiiGAB 810
4. Connect PiiGAB 810 gateway to a 24V AC or DC power supply
5. Turn the power supply on
6. Wait for PiiGAB 810’s Pwr LED to go steady red
M-Bus
meter
Power supply
24V AC/DC
Network
Patch cable
Getting started PiiGAB 810 Rev 1.00.01
© PiiGAB Processinformation i Göteborg AB Page: 5
4. PiiGAB 810’s MAC-address
On the right gable of the PiiGAB 810 you’ll find a label containing the MAC-address of your
PiiGAB 810. You can use this to identify your PiiGAB 810 with the PiiGAB M-Bus Setup
Wizard software.
Object
Starts with
MAC-address - old
00-20-4A-XX-XX-XX
MAC-address - new
00-80-A3-XX-XX-XX
5. IP-configuration
You can either connect your PiiGAB 810 gateway to a static or DHCP network. The most
common IP-configuration of the PiiGAB 810 gateway is for static IP-address. The gateway is
by default set to DHCP when delivered.
5.1 DHCP network
If you have a network with DHCP you can connect your PiiGAB 810 gateway to it and the
gateway will receive the IP-configuration automatically.
5.2 Static IP
If you don’t have a network with DHCP you must set your PiiGAB 810 gateway to a static IP-
address.
Note: If you have an old computer you might need a network switch between your
computer and the PiiGAB 810 gateway.
1. Set your computer to a static IP-address
2. Start the PiiGAB M-Bus Setup Wizard and go to the main menu
3. Select Change gateway IP-settings
4. Press Next to continue
Getting started PiiGAB 810 Rev 1.00.01
© PiiGAB Processinformation i Göteborg AB Page: 6
5. Select Setup IP using network (UDP broadcast)
6. In the MAC-address field specify the PiiGAB 810 gateway’s MAC-address
7. Press Next to continue
8. Select Use the following IP-address
9. Specify the IP-configuration. The PiiGAB 810 gateway should match your computer’s
IP-address
10. Press Next to continue
Getting started PiiGAB 810 Rev 1.00.01
© PiiGAB Processinformation i Göteborg AB Page: 7
11. Press Apply to set the IP-configuration
12. Wait for the PiiGAB 810 gateway to reboot
13. Press Next to continue to the main menu
Getting started PiiGAB 810 Rev 1.00.01
© PiiGAB Processinformation i Göteborg AB Page: 8
6. Find your PiiGAB 810 on your network
You can use the PiiGAB M-Bus Setup Wizard to find your gateway on the network. This will
work for both a network with DHCP or static IP-address configuration.
1. Go to the main menu in the PiiGAB M-Bus Setup Wizard
2. Select Find gateways on your network
3. Press Next to continue
4. Your PiiGAB 810 gateway should be listed
5. Find your PiiGAB 810 by the MAC-address column
6. Select your PiiGAB 810 gateway and press Next
Note: If you placed your PiiGAB 810 gateway on a different sub network you might not find it
in the list of available gateways.
Getting started PiiGAB 810 Rev 1.00.01
© PiiGAB Processinformation i Göteborg AB Page: 9
7. Configure the PiiGAB 810
This section describes how the PiiGAB 810 should be configured for M-Bus communication
for 2400 baud, UDP and port 10001.
1. In the PiiGAB M-Bus Setup Wizard’s main menu click the Change gateway
parameters
2. Press Next to continue
3. Select Connect using network
Note: Make sure the PiiGAB 810 gateway’s IP-address is shown in IP-address/DNS
field
4. Press Next to continue
Getting started PiiGAB 810 Rev 1.00.01
© PiiGAB Processinformation i Göteborg AB Page: 10
5. Configure the PiiGAB 810 with these settings
6. Press the Apply button to continue
7. Wait for the program to finish the configuration of the PiiGAB 810 gateway
8. Press Next to continue
Tabla de contenidos
Otros manuales de Puerta de PiiGAB
Manuales populares de Puerta de otras marcas
LST
LST M500RFE-AS Manual de usuario
Kinnex
Kinnex Media Gateway Manual de usuario
2N Telekomunikace
2N Telekomunikace 2N StarGate Manual de usuario
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Manual de usuario
ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE Manual de usuario
Telsey
Telsey CPVA 500 - SIP Manual de usuario
