Piergiacomi TP-6000 Manual de usuario
TPP
INSTRUCTION MANUAL
Page 1 Date rev. 28/05/13
Rev. 07
INSTRUCTION MANUAL
TPP
REV. 07
TP
-
6000
CUT and BEND
TP
-
6000
-
15
CUT and BEND
TS
-
6000
CUT and CRIMP
TR
-
6000
CUT
TR
-
6000
-
V
60° CUT
TPP
INSTRUCTION MANUAL
Page 2 Date rev. 28/05/13
Rev. 07
INDEX OF CHAPTER
This manual contains the following information:
- Chapter 1 – Page 3 – Safety symbol and rules to observe
- Chapter 2 – Page 4 – Introduction
- Chapter 3 – Page 5 – Components parts
- Chapter 4 – Page – Blade specifications
- Chapter 5 – Page 10 – Using the tool
- Chapter 6 – Page 13 – Servicing and maintenance
- Chapter – Page 14 – How to change blades
- Chapter 8 – Page 15 – Optional accessories
- Chapter 9 – Page 15 – Characteristics
Page 16 – Conformity Declaration
NOTICE
The manufacturer reser es the right to change or modify the information
contained in this manual at any time without prior warning.
TPP
INSTRUCTION MANUAL
Page 3 Date rev. 28/05/13
Rev. 07
1. SAFETY SYMBOLS AND RULES TO OBSERVE
Before any kind of adjustment or registration to be performed on the device,
be sure the compressed air supply system is not connected.
WARNING!!! Piergiacomi Sud S.r.l. refuses all responsibilities for any damage
caused to operators if the de ice’s chassis has been remo ed or modified;
therefore it is strictly forbidden to perform any maintenance or registration
while the de ice is in use.
- This type of symbol on the tool means: “DO NOT PUT
YOUR HANDS” between the blades of the tool during
operation.
- Always use protecti e glasses while the tool is operating.
- Turn off the compressed air supply each time the tool is lean on
without using it.
- After use place the tool in a safety location and disconnect it from
the compressed air supply system.
- Observe and carry out the indications and warnings shown on the
special stickers on the tool.
TPP
INSTRUCTION MANUAL
Page 4 Date rev. 28/05/13
Rev. 07
2. INTRODUCTION
2.1 TR-6000 – TR-6000-V
Piergiacomi has become aware of the enormous problems associated with staff that, during the working
day, carry out multiple cutting operations, in any sector, from electronics to the plastic or rubber industry.
We have studied the problem and obtained the TR-6000, thanks to our vast experience in industry tools,
the ideal lightweight tool and with reduced costs.
Furthermore, it’s available the TR-6000-V model too, which has a flush front 60° angled cut, in order to
have the access in difficult points.
This is the basis of our philosophy and our product has been designed to meet both performance and
safety requirements.
Example: At the end of the component mounting stage of an electronic printed circuit board, the
requirement of cutting multiple leads without causing damage to the components is needed. Therefore
the most qualified solution is to carry out in a fast and efficiently way flush or chamfered cut or a cut at
different heights.
With the wide range of types of tips we enable you to reach normally not much accessible parts as shown
in the diagram.
In the plastic sector, as in that of rubber, cutting the parts without causing damage, when
removing the excess material created by the moulds, is a common problem. –The TR-6000 model
is suitable for cutting small diameters of rubbing material. For cutting bigger diameters,
Piergiacomi developed several solutions, like the TPP-TM-6000.
TPP
INSTRUCTION MANUAL
Page 5 Date rev. 28/05/13
Rev. 07
2.2 TP-6000 - TP-6000-15 - TS-6000
Those who work in the electronics sector frequently have the problem of blocking the components on the
printed circuit board before and during the soldering phase. In order to solve the problem, Piergiacomi
has designed and produced these tools, the TP-6000, which cuts the component leads and bends them
so as to fix them firmly in place to the board. The operator that will later perform the soldering phase will
therefore not have that troublesome problem of components that have been displaced or in the worst
case become loose and fallen off the board.
The TP-6000 or TP-6000-15 proves to be an enormously special tool as it manages to carry out two
functions in one operation and furthermore has the advantages of being a lightweight and reduced costs
pneumatic tool.
This is the basis of our philosophy and our product has been designed to meet both performance and
safety requirements.
3. COMPONENTS PARTS
The main characteristic of the TPP is the possibility to interchange the fix base (body) TPP, as shown in the
Fig. 1 with the several heads or with specific blades for the required work.
Every time a change of works is needed, it’s enough to replace, in a simply and fast way, the upper part
(head) of the tool. See instructions on Chapter .
Example of part number: TPP-TP-6000
VALVE
HOOK
AIR
CONNECTOR
Ø6
LEVER
AIR
CHAMBER
HEAD
HEAD
CUTTING
BLADES
CUTTING
BLADES
Fig. 1
TPP
INSTRUCTION MANUAL
Page 6 Date rev. 28/05/13
Rev. 07
3.1 TPP
3.2 TP-6000 TP-6000-15
Fig. 2
Fig. 3
TPP
INSTRUCTION MANUAL
Page 7 Date rev. 28/05/13
Rev. 07
3.3 TR-6000 TR-6000-V TS-6000
4. BLADE SPECIFICATIONS
The blades are made from grinded & tempered special steel and can be easily replaced, as explained in
Chapters of this manual.
- TP-6000
Cut & Bend blades for blocking the leads of the component on the PCB. (Max cut 1.02 mm)
Fig. 5
–
TP
-
6000
Fig. 4
TPP
INSTRUCTION MANUAL
Page 8 Date rev. 28/05/13
Rev. 07
- TP-6000-15
Cut and Bend Blades for blocking the leads of the component on the PCB, to reach very dense areas.
(Max cut 1.02 mm)
- TR-6000
Blades TR-6000 are supplied standard with 2 typology of cuts (Fig. ):
- CHAMFERED (code TR-6000): permit also to cut harder components & a number of unlimited cuts
without damaging the blades.
- FLUSH (code TR-6000-R): permit to make flush and precise cuts. Suggested in particular where a
absolute accuracy of cut is needed.
Flush cut Chamfered cut
Fig. 6
–
TP
-
6000
-
15
FLUSH
CUT CHAMFERED
CUT
Fig. 7
TPP
INSTRUCTION MANUAL
Page 9 Date rev. 28/05/13
Rev. 07
TR-6000 blade (chamfered cut, Max cut 1.6 mm, Fig. 5) is available in different versions, as shown on our
catalogues:
- TR-6000 R
(Max cut 1.6 mm) with flush cut.
- TR-6000 PR
(Max cut 1.3 mm) with flush cut, but more pointed tips.
- TR-6000 10/13/15
(Max cut 1.6 mm) with flush cut at different height (1.0mm, 1.3mm &
1.5mm) from the surface.
- TR-6000 C
(Max cut 1.6 mm) with shorter and stronger blades.
- TR-6000-V
Flush front 60° angled blades, in order to have the access in difficult points.(Max cut 1.3 mm).
Fig.
8
–
TR
-
6000
SUGGESTED
CUTTING
POINT
Fig. 9
–
TR
-
6000
-
V
TPP
INSTRUCTION MANUAL
Page 10 Date rev. 28/05/13
Rev. 07
- TS-6000
Cut & Press blades, for blocking the leads of the component on the PCB. (Max cut 1.3 mm).
Special blades suitable for your purposes are produced at request!
5. USING THE TOOL
Before using this de ice, read carefully Chapter 1 (Safety Symbols and Rules to
obser e).
Warning!
Always wear protecti e glasses during the use of the tool and do not
work with your fingers close to the blades while mo ing.
Warning!
After using, put de ice in a safety place and disconnect compressed
air supply system.
The tool should be used at the angle shown in the figures with respect to the working surface.
Fig.
11
–
TP
-
6000
Fig. 10
–
TS
-
6000
Este manual sirve para los siguientes modelos
4
Tabla de contenidos
Manuales populares de Cortador de otras marcas
Milwaukee
Milwaukee HEAVY DUTY M12 FCOT Manual de usuario
Makita
Makita DCS552 Manual de usuario
SignWarehouse.com
SignWarehouse.com Bobcat BA-60 Manual de usuario
Makita
Makita 4112HS Manual de usuario
GEISMAR STUMEC
GEISMAR STUMEC MTZ 350S Manual de usuario
Hitachi
Hitachi CM 4SB2 Guía de solución de problemas
