PicoBrew Zymatic Manual de usuario

Zymatic® User Manual

Important Safety Information

!Read all instructions before operating the machine.

!Exercise common sense while operating the Zymatic.

!Always use the keg cozy to shield the hot metal of the keg.

!Close supervision is needed when used around children.

!Allow machine to fully cool before removing or replacing parts.

!Do not operate with a frayed or broken plug.

!Test the GFCI circuit breaker on the plug before every brew.

!Do not remove step filter from the Zymatic unless in pause mode or brewing is completed.

!The step filter and contents may be hot when removing from the machine.

!Do not immerse or soak the machine.

!Make sure all hoses are connected before starting a recipe, rinse or cleaning cycle.

!There are no user serviceable parts inside. To avoid risk of electric shock hazard do not disassemble the Zymatic.

!Various surfaces can get extremely hot during the brewing cycle, use caution when handling the keg, hoses and components.

!Do not remove the hose clamps, hot liquid spray may result.

!Do not remove the keg attachments while brewing.

A. Zymatic®

B. 1 6’ Power Cord

C. 1 USB Cable

D. 1 25’ Ethernet Cable

E. Diptube Cleaning Brush

F. 1 In Hose (gray ball lock)

G. 1 Out Hose (black ball lock)

H. 1 Party Tap

I. 1 Transfer Tube

Unpack the Zymatic®

J. 1 Step Filter Lid

K. 1 Adjunct Compartment

L. 4 Hop Cages and Lids

M. 1 Adjunct Screen

N. 1 Step Filter

O. 2 Mash Screens

P. 1 Foam Trap

Q. 2 Needle-less Syringes

R. 1 Package of PBW

S. 1 Dishwasher Tablet

T. 1 Bottle of Antifoam

Unpack the Zymatic®

A. Zymatic®

B. 1 6’ Power Cord

C. 1 USB Cable

D. 1 25’ Ethernet Cable

E. Diptube Cleaning Brush

F. 1 In Hose (gray ball lock)

G. 1 Out Hose (black ball lock)

H. 1 Party Tap

I. 1 Transfer Tube

J. 1 Step Filter Lid

K. 1 Adjunct Compartment

L. 4 Hop Cages and Lids

M. 1 Adjunct Screen

N. 1 Step Filter

O. 2 Mash Screens (different sizes)

P. 1 Foam Trap

Q. 1 Needle-less Syringe

R. 1 Package of PBW

S. 1 Dishwasher Tablet

Included, not pictured:

1 plastic hose wrench

4 small white nylon washers

4 silicone bands

1 Keg Seal

1 airlock

1 Party Porter ingredient kit

T. 1 Bottle of Antifoam

U. 2 Cleaning Tubes

V. 1 Keg Cozy

Gather Materials

Before You Brew

Zymatic (A)

(assembled with Power Cord (B), In Hose (F), Out Hose (G), plastic

hose wrench and 2 white cone seat seals)

Step Filter Lid (J)

Step Filter (N)

Mash Bottom Screen (O)

Adjunct Screen (M)

Corny Keg

Keg Seal

1 gallon of water

During Your Brew

Zymatic

Step Filter Lid (J)

Adjunct Compartment (K)

Cages (L)

Step Filter (N)

Adjunct Screen (M)

Mash Top and Bottom Screen (O)

Foam Trap (P)

Anti-Foam (T)

Keg Cozy (T)

5-gallon Corny Keg

Keg Seal

Water (amount varies by recipe)

Recipe kit (grains, hops, yeast)

Post-Brew

5-gallon Corny Keg (with wort)

Ice

5-gallon bucket

Yeast

Airlock

Sanitized water or alcohol

Rinse

Zymatic

Step Filter (N)

2 large containers for water

1 gallon of water

2 Cleaning Tubes (U)

Deep Clean

Zymatic

Step Filter (N)

Dishwasher Tablet (S)

1 gallon of water

2 large containers for water

2 Cleaning Tubes (U)

Miscellaneous

Sampling from the Sampling Port

Needleless Syringes (Q)

Keg Cleaning

Diptube Cleaning Brush (E)

Pro Brewers Wash (R)

Racking/Transferring

Transfer Tube (I)

Sampling from Keg/Serving

Party Tap (H)

Non-WiFi Internet Connection

Ethernet Cord (D)

Firmware Updates

USB Cable (C)

How the Zymatic®Works

Mash

Heat

Grains go in the mash compartment,

where wort is filtered through the

mesh false bottom and recirculated

through the keg and Zymatic, which

controls the temperature.

Hops are boiled in cages in the Adjunct Compartment. Each

cage corresponds to a timed addition to the boil. The

cascading motion caused by the Adjunct Compartment mimics

manually adding hops to a boil pot. When a new hop addition

is added, the cascade motion continues to boil the previous

addition, while keeping the others dry until they are added.

To heat the water or wort up to either mash or

boil temperature, the Zymatic will bypass the

grain and hops in an area of the Step Filter

called the Pass Through. The Pass Through is

the narrow area between the Mash

Compartment and the Adjunct Compartment.

When water or wort is heating up, it passes

through directly to the bottom of the step filter,

where it circulates through the drain and back

into the keg. The Zymatic has been calibrated to

keep the water level in the bottom of the step

filter below the grain and hops, so they are only

incorporated when the recipe calls for it.

Boil

Operating the Zymatic®

On/Off Switch

OLED Display

Selector Knob

twist to scroll

press to select

Inline Filter

IN Hose

connects to IN post of keg

controls flow into keg

OUT Hose

connects to OUT post of keg

controls flow into Step Filter

Step Filter

Drip Tray

Display

Main Menu

Brew a Recipe

Select to see the list of recipes synced to your Zymatic, then

select one to brew.

Clean/Rinse

Clean: Use this program for a deep clean every 5 brews with a

dishwasher tablet.

Rinse: Use this program after initial set-up and after every brew

to rinse out your machine.

Machine Set-Up

Ethernet: Use to check your Ethernet connection. You must

have an Ethernet cable connected.

WiFi: Use to check your WiFi connection.

Account Sync: Use to sync recipes to your account if it didn’t

automatically sync.

Help

Drain: Will drain the machine for 5 minutes or until you

manually press stop.

Circulate: Will run the keg and drain pump while displaying the

current temperatures. Do not select this option if you do not

have a Step Filter inserted and a keg or tubes connected to your

ball locks.

System Diagnostics: This option will lead through a

diagnostics test that will allow PicoBrew to help you figure out

the cause of any issues you may run into with your Zymatic®.

Help from PicoBrew: Select if you are seeing any issues with

your machine and your Zymatic® will send an error log and

contact customer support at PicoBrew.

Continue from Last Brew: If for some reason your Zymatic®

ran into a power fault or any other errors and stopped your brew

and it is now safe to continue your brew, you can select this

option to continue where you left off.

About Zymatic

Information on account information, serial numbers, and

firmware version.

Display

Brew Menu

(Pressing the selector knob during a brew will bring up a menu, while the brew continues normally.)

Continue

Leaves the menu and continues the brew normally. The time and temperature regulation continues while you are in the menu, although

it will not move to a new step until you leave the menu.

Next Step

Will skip immediately to the next programmed step in the brew. It does not recognized programmed drains, however, so use caution if

you are skipping through during mash, as it will not automatically drain.

Drain

Flow from the keg will stop, and the Zymatic®will drain the step filter until you press Continue.

Exit Brew

Exits brew immediately and goes to the main menu. Use caution as this will also skip all programmed drains and will not continue

where you left off.

Set Up the Zymatic®

1) Set the Zymatic®on a sturdy, level surface, such as a

kitchen counter. Peel off any remaining white protective

film from all surfaces.

2) Attach the hoses to the machine (Parts F and G) using

the included black plastic wrench.

a. Place one white nylon washer inside of the flare

nut fitting on the end of each hose before attaching the hose to the

Zymatic®. This prevents the hose from pumping air or leaking.

b. Make sure the OUT hose (with the filter) is the closer of the hoses toward

the back of the Zymatic®.

c. Hand tighten first by screwing the flare nut onto the Zymatic® and then

use the black plastic wrench to tighten it further.

d. Keep the black plastic wrench and extra nylon washers with this manual

in case they are needed for any repairs.

Front

Back

IN hose

OUT hose

3) Plug the power cord into the back of the machine and into an outlet. The

Zymatic® requires at least a 15 amp outlet (standard in most houses.) Do not

overload an outlet with appliances that will use more than 15 amps.

4) If using Ethernet, plug in an Ethernet cord into the back of the machine. If you

are using WiFi, skip this step. WiFi set up will be completed upon the initial

startup of the Zymatic® with on-screen instructions.

Otros manuales para Zymatic

Tabla de contenidos

Otros manuales de Sistema de elaboración de cerveza de PicoBrew

PicoBrew

PicoBrew Z Series Manual de usuario

PicoBrew

PicoBrew Z Series Manual de usuario

PicoBrew

PicoBrew C Manual de usuario

PicoBrew

PicoBrew Z Manual de usuario

PicoBrew

PicoBrew PicoStill Instrucciones de funcionamiento

PicoBrew

PicoBrew Z2 Manual de usuario

PicoBrew

PicoBrew Pico C Manual de usuario

PicoBrew

PicoBrew 2AJZKS1PICO Manual de usuario

PicoBrew

PicoBrew Z Series Manual de usuario

Manuales populares de Sistema de elaboración de cerveza de otras marcas

CBF-DRINKIT

CBF-DRINKIT Coobra CB25 Manual de usuario

Toddy

Toddy ARTISAN Manual de usuario

Bunn

Bunn GRX Manual de usuario

Keurig

Keurig Vue Manual de usuario

VKI Technologies

VKI Technologies Zuma Brewer Manual de operación

Speidel

Speidel Braumeister PLUS 10 litres Manual de usuario

BrewBuilt

BrewBuilt X2 UNI Manual de usuario

Tribest

Tribest RAW TEA KETTLE Manual de usuario

Sprowt Labs

Sprowt Labs Acro Manual de usuario

KegLand

KegLand Robobrew Manual de usuario

BRAVILOR BONAMAT

BRAVILOR BONAMAT Aurora GTBSH-001 Manual de usuario

Fetco

Fetco CBS-1221 Especificaciones

Curtis

Curtis ThermoPro G4 Series Manual de usuario

Animo

Animo ComBi CB5 Manual de usuario

MoreBeer

MoreBeer BrewSculpture Manual de usuario

Keurig Hot

Keurig Hot Commercial Series Manual de usuario

Keg King

Keg King KEGMASTER XL Manual de usuario

Blichmann Engineering

Blichmann Engineering BrewEasy Compact TC Instrucciones de instalación