Pickering 40-570A Manual de usuario

pickeringtest.com

Issue 1.1 February 2020

40-570A User Manual

PXI High Density Multiplexer BRIC™ Module

Page (II) HIGH DENSITY MUX BRIC 40-570A

pickering

Page (II) REED RELAY MODULE 40-110/115/120/125

pickering

No part of this publication may be reproduced, transmitted, transcribed, translated or stored in any form, or by

any means without the written permission of Pickering Interfaces.

Technical details contained within this publication are subject to change without notice.

ISO 9001

Reg No. FM38792

Page (III)

HIGH DENSITY MUX BRIC 40-570A

pickering

Page (III)

REED RELAY MODULE 40-110/115/120/125

pickering

TECHNICAL SUPPORT

For Technical Support please contact Pickering Interfaces either by phone, the website or via e-mail.

WARRANTY

All products manufactured by Pickering Interfaces are warranted against defective materials and workmanship for a period of

three years, excluding programmable power supplies, from the date of delivery to the original purchaser. Any product found to be

defective within this period will, at the discretion of Pickering Interfaces be repaired or replaced.

Products serviced and repaired outside of the warranty period are warranted for ninety days.

Extended warranty and service are available. Please contact Pickering Interfaces by phone, the website or via e-mail.

ENVIRONMENTAL POLICY

Pickering Interfaces operates under an environmental management system similar to ISO 14001.

Pickering Interfaces strives to full all relevant environmental laws and regulations and reduce wastes and releases to the

environment. Pickering Interfaces aims to design and operate products in a way that protects the environment and the health and

safety of its employees, customers and the public. Pickering Interfaces endeavours to develop and manufacture products that can

be produced, distributed, used and recycled, or disposed of, in a safe and environmentally friendly manner.

Worldwide Technical Support and Product Information

pickeringtest.com

Germany

Tel: +49 89 125 953 160

E-mail: [email protected]

Sweden

Tel: +46 340-69 06 69

E-mail: [email protected]

USA

Tel: (West) +1 541 471 0700

Tel: (East) +1 781 897 1710

E-mail: [email protected]

Czech Republic

Tel: +420 558 987 613

E-mail: [email protected]

France

Tel +33 9 72 58 77 00

E-mail [email protected]

Pickering Interfaces Headquarters

Stephenson Road Clacton-on-Sea CO15 4NL United Kingdom

Tel: +44 (0)1255-687900

E-Mail: [email protected]

China

Tel: +86 4008 799 765

E-mail: [email protected]

Page (IV) HIGH DENSITY MUX BRIC 40-570A

pickering

Page (IV) REED RELAY MODULE 40-110/115/120/125

pickering

MEANING / DESCRIPTION SYMBOL

PROTECTIVE EARTH (GROUND)

To identify any terminal which is intended for connection to an external conductor for

protection against electric shock in case of a fault, or the terminal of a protective earth

(ground) electrode.

DANGEROUS VOLTAGE

To indicate hazards arising from dangerous voltages.

WARNING / CAUTION

An appropriate safety instruction should be followed or caution to a potential hazard

exists.

Refer to the relevant instructions detailed within the product manual.

HEAVY

If this product is heavy reference should be made to the safety instructions for

provisions of lifting and moving.

STATIC SENSITIVE

To indicate that static sensitive devices are present and handling precautions should

be followed.

SAFETY SYMBOLS

PRODUCT SAFETY

The following safety symbols may be used on the product and throughout the product documentation.

Page (V)

HIGH DENSITY MUX BRIC 40-570A

pickering

Technical Support and Warranty................................................III

Product Safety .............................................................................IV

Contents (this page)....................................................................V

Warnings and Cautions ..............................................................VII

Section 1

Technical Specication...............................................................1.1

Section 2

Technical Description .................................................................2.1

Mechanical Description ........................................................2.1

Functional Description .........................................................2.1

Section 3

Installation....................................................................................3.1

Pre Operation Checks...........................................................3.1

Hardware Installation ............................................................3.2

Software Installation .............................................................3.2

Testing Operation ..................................................................3.3

Section 4

Programming Guide....................................................................4.1

Programming Options for PXI Modules ..............................4.1

Module Architecture..............................................................4.2

Programming The Module ....................................................4.3

Using Pickering Drivers in LabVIEW ...................................4.5

Section 5

Connector Information................................................................5.1

Section 6

Troubleshooting ..........................................................................6.1

Section 7

Maintenance Information............................................................7.1

Fuse Replacement.................................................................7.1

Relay Look-Up Tables ...........................................................7.1

PCB Layout Diagrams...........................................................7.16

Module Removal From Chassis ...........................................7.18

Card Removal From BRIC.....................................................7.20

Card Replacement.................................................................7.22

CONTENTS

Page (VI) HIGH DENSITY MUX BRIC 40-570A

pickering

THIS PAGE INTENTIONALLY BLANK

Page (VII)

HIGH DENSITY MUX BRIC 40-570A

pickering

Page (VII)

2 AMP 1-POLE UHD MATRIX MODULES 40-575 / 576 / 577 / 578 / 579

pickering

WARNINGS AND CAUTIONS

WARNING - HAZARDOUS ENVIRONMENTS SYMBOL

This product is not specically designed for use in hazardous environments, for example in explosive

atmospheres. If the product is to be used in hazardous environments we recommend that the user

ensures suitable protective measures are taken.

WARNING - DANGER OF ELECTRIC SHOCK SYMBOL

This module may contain hazardous voltages. Before removing the module from the rack remove all

supplies and disconnect user I/O signals.

Unused slots in the host chassis are populated with blanking plates to prevent access to user I/O

signals that may be present. Blanking panels are available to order from Pickering in a variety of

slot widths. If the product is not used in this manner for example by using an extender card then

additional care must be taken to avoid contact with exposed signals.

Not to be used in safety critical circuits, refer to the Pickering Interfaces’ terms & conditions of sale.

This module must not be used for the switching of Mains Circuits. For the switching of voltages up

to the module’s full specication, Secondary Circuit power supplies and the Device Under Test must

be fully isolated from the Mains Circuit and the safety earth.

The host chassis must be correctly installed and be connected to mains or factory safety ground,

please refer to your chassis installation manual.

Diagram Showing Separation Between The Mains Circuit and Secondary Circuit / DUT

For the purposes of this document, a Mains Circuit is an installation classied as Overvoltage

Category II up to 300V. Separation between the Secondary Circuit and Mains Circuit is achieved

by a transformer in which the primary windings are separated from the secondary windings by

reinforced insulation, double insulation, or a screen connected to the protective conductor terminal.

CAUTION - HANDLING OF ELECTROSTATIC-SENSITIVE DEVICES SYMBOL

Certain semiconductor devices used in this equipment are liable to damage due to static voltage.

Observe the following precautions when handling these devices in their unterminated state, or

sub-assemblies containing these devices:

1. Persons removing sub-assemblies from equipment using these devices must be earthed by a

wrist strap and a resistor at the point provided on the equipment.

2. Soldering irons used during the repair operations must be low voltage types with earthed tips and

isolated from the mains voltage by a double insulated transformer.

3. Outer clothing worn must be unable to generate static charges.

4. Printed Circuit Boards (PCBs) tted with these devices must be stored and transported in

anti-static bags.

PXI Switching

Module

Device

Under Test

Power

Supply

Power

Supply

Host Chassis

Secondary Circuit

Mains

Circuit

Mains

Circuit

Mains/Factory

Safety Ground

Page (VIII) HIGH DENSITY MUX BRIC 40-570A

pickering

Page (VIII) 2 AMP 1-POLE UHD MATRIX MODULES 40-575 / 576 / 577 / 578 / 579

pickering

CAUTION - PRODUCT DOCUMENTATION SYMBOL

Suitably qualied & trained users should ensure that the accompanying documentation is fully read

and understood before attempting to install or operate the product.

SAFETY INSTRUCTIONS

All cleaning and servicing requires the equipment to be isolated and disconnected from the power source and user I/O

signals (refer to the Maintenance Section).

• Appropriate manual handling procedures should be followed as dictated by the weight of the individual module or

the combined weight of the modules & chassis.

• Should a fault occur with the module or chassis, immediately isolate and disconnect the incoming power to the

chassis and the user I/O signals.

• Ensure the equipment is installed, operated and maintained by trained and authorised personnel.

• For suitably equipped products in the event of an emergency press the red “emergency stop” button situated on

the front of the unit.

Page 1.1

HIGH DENSITY MUX BRIC 40-570A

pickering SECTION 1 - TECHNICAL SPECIFICATION

SECTION 1 - TECHNICAL SPECIFICATION

pickeringtest.com

PXI High Density MUX BRIC™ 40-570A

ISSUE 1.0 FEB 2019

• High Density Multiplexer With Multiple

Conﬁguration Options

• Wide Range of Sizes up to 6-Channel/160-Pole,

12-Channel/80-Pole, 24-Channel/40-Pole,

48-Channel/20-Pole, & 96-Channel/10-Pole

• Scalable (up to 6 relay cards)

• Expandable Via Common Loop-Thru Connector

With Isolation Switching for Optimal Signal

Integrity in Larger Systems

• Maximum Switch Current of 1A

• Switch up to 100V and up to 60W Max Power

• VISA, IVI & Kernel Drivers Supplied for

Windows

• Supported by PXI or LXI Chassis

• 3 Year Warranty

Switching Diagram for 40-570A High Density MUX In

6-Channel 160-Pole Format

CH1.1

CH5.2

CH5.160

CH1.2

CH1.160

CH5.1

CH6.2

CH6.160

CH6.1

CH2,2

CH2.160

CH2.1

CH3.2

CH3.160

CH3.1

CH4.2

CH4.160

CH4.1

COM.1

COM.2

COM.160

160 Poles

Channel 1

Channel 2

Channel 3

Channel 4

Channel 5Channel 6

Common Loop-Thru

COM-LT.2

COM-LT.160

COM-LT.1

Common

The 40-570A is a High Density Multiplexer designed to simplify

the connection of a common set of test equipment to one of a

number of different devices for testing. It is ideal for applications

where the equipment needs to conduct the same test process

on a series of similar devices one at a time. It is available in a

variety of congurations that allow testing with differing number

of devices to be tested and different connection widths to suit

differing test equipment pin counts.

The 40-570A can be operated as a conventional multiplexer

with break-before-make action when a new channel is selected.

Alternatively, variants of the multiplexer can be supplied that

allow multiple channels to be simultaneously selected.

The 40-570A channel selection congurations have been

revised from the 40-570. The 40-570A module defaults to single

channel selection with multiple channel selection variants

dened by use of a sufx.

All versions of the 40-570A are supported in a BRIC8 format

that occupies 8 PXI 3U mechanical slots, one of which provides

the PXI interface and power.

MUX size can be ordered with different widths (pole counts)

and with different numbers of relay cards to support varying

number of devices to be tested. For example, the fully

populated 40-570A can be ordered in congurations supporting:

• 6 test devices with 160 connections

• 12 test devices with 80 connections

• 24 test devices with 40 connections

• 48 test devices with 20 connections

• 96 test devices with 10 connections

The pin layout of user connection is arranged to simplify the

cabling design. All versions use high quality electro-mechanical

relays with palladium-ruthenium gold covered contacts.

Page 1.2 HIGH DENSITY MUX BRIC 40-570A

pickering

SECTION 1 - TECHNICAL SPECIFICATION

High Density MUX BRIC – 40-570A

pickeringtest.com

Overview

CH1

CH3

CH2

CH4

CH5

CH6

160

CH1

CH3

CH2

CH4

CH5

CH6

CH7

CH8

80 80

CH9

80 80

CH10

80 80

CH11

80 80

CH12

80 80

CH1

CH3

CH2

CH4

CH5

CH6

CH7

CH8

40 40

CH9

40 40

CH10

40 40

CH11

40 40

CH12

40 40

CH13

40 40

CH14

40 40

CH15

40 40

CH16

40 40

CH17

40 40

CH18

40 40

CH19

40 40

CH20

40 40

CH21

40 40

CH22

40 40

CH23

40 40

CH24

40 40

CH1

CH3

CH2

CH4

CH5

CH6

CH7

CH8

20 20

CH41

20 20

CH42

20 20

CH43

20 20

CH44

20 20

CH45

20 20

CH46

20 20

CH47

20 20

CH48

20 20

CH1

CH3

CH2

CH4

CH5

CH6

CH7

CH8

10 10

CH89

10 10

CH90

10 10

CH91

10 10

CH92

10 10

CH93

10 10

CH94

10 10

CH95

10 10

CH96

10 10

COM

160

LOOP-

THRU

160

COM

LOOP-

THRU

COM

LOOP-

THRU

COM

LOOP-

THRU

COM

LOOP-

THRU

6-Channel, 160-pole

Multiplexer

12-Channel, 80-pole

Multiplexer

24-Channel, 40-pole

Multiplexer

48-Channel, 20-pole

Multiplexer

96-Channel, 10-pole

Multiplexer

Switching Diagrams for the Five Possible Fully Populated Switching Conﬁgurations Available for the

40-570A High Density BRIC Multiplexer

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Multiplexor de Pickering

Pickering

Pickering 40-616 Manual de usuario

Pickering

Pickering 40-612A Manual de usuario

Pickering

Pickering 40-670 Manual de usuario

Pickering

Pickering 40-735 Manual de usuario

Pickering

Pickering PXI 40-882B Manual de usuario

Pickering

Pickering 40-652A Manual de usuario

Pickering

Pickering PCI 50-725 Manual de usuario

Pickering

Pickering SYSTEM 10 Manual de usuario

Pickering

Pickering 40-657 Manual de usuario

Pickering

Pickering 40-736 Manual de usuario

Pickering

Pickering 40-682A Manual de usuario

Pickering

Pickering LXI 60-890-053 Manual de usuario

Pickering

Pickering LXI 60-802 Manual de usuario

Pickering

Pickering PXI Power MUX BRIC 40-571A Manual de usuario

Pickering

Pickering 40-756 Manual de usuario

Pickering

Pickering PXI 40-740 Manual de usuario

Pickering

Pickering 40-614C Manual de usuario

Pickering

Pickering 40-616A Manual de usuario

Pickering

Pickering 4 878 Series Manual de usuario

Pickering

Pickering PXI 40-661A Manual de usuario

Pickering

Pickering 40-681A Manual de usuario

Pickering

Pickering 40-667C Manual de usuario

Pickering

Pickering 40-617A Manual de usuario

Pickering

Pickering 40-619 Manual de usuario

Manuales populares de Multiplexor de otras marcas

Campbell

Campbell AM416 Manual de usuario

Paradyne

Paradyne SIM2000 Manual de usuario

Panasonic

Panasonic WJFS616 - SWITCHER Manual de usuario

Lanex

Lanex TM-77 Manual de usuario

Bosch

Bosch VSS8394/01T Manual de usuario

Quark-Elec

Quark-Elec QK-A035 Manual de usuario

ADTRAN

ADTRAN Frameport 768 Manual de usuario

Elo TouchSystems

Elo TouchSystems E247 Manual de usuario

Paradyne

Paradyne Hotwire 8786 Manual de usuario

RFL Electronics

RFL Electronics 9508D UCC Manual de usuario

Miranda

Miranda AMX-101i Manual de instrucciones

ShipModul

ShipModul MiniPlex-AIX NMEA-0183 Manual de usuario

GE StoreSafe SDVR-10 Manual de usuario

American Fibertek

American Fibertek MTX-8410C Manual de usuario

ADC

ADC HiGain ELU-319 5E Manual de usuario

Paradyne

Paradyne Hotwire 8774 Manual de usuario

American Fibertek

American Fibertek MTX-8810C-SL Manual de usuario

Viessmann

Viessmann 5229 Manual de usuario