Piaa RS400 Manual de usuario
Shock Lamp RS400 H.I.D.
Installation Instructions
Thank you very much for purchasing this PIAA product.
Please read the entire manual before installation and use of this product.
FOR INSTALLERS
Please give this installation manual to customer after installing.
When installing two lamps on the vehicle, it is necessary to purchase another relay harness
(PN 34035). One harness is required for each lamp.
• Lighting laws vary from state to state.
Check your local laws before use.
• The lamps get very hot when they have been in use.
Do not touch them as they may cause burns.
• After the lights have been on, do not place them near ammable objects.
• Do not splash water directly on the hot lamps, as this may cause cracking of the lens due
to dramatic change in temperature.
• To avoid potential damage to your eyes, do not look directly into the lamp.
• This product is designed for 12V automotive electrical systems only.
• Using this light system while the engine is not running will drain the battery.
• Do not repeatedly turn the light system on and o as it will shorten the life of the system.
• To avoid potential damage to your lights, make sure your lights are turned on prior to
starting or shutting o your vehicle.
• Using the wrong bulbs may cause a malfunction. Use only specied PIAA bulbs.
• When changing bulbs or lenses follow the lamp assembly/disassembly diagram.
WARNING
1
• When activated, this system operates at extremely high voltage (20,000V).
DO NOT turn on the switch when holding the cord that connects the ballast and the
lamp!
• Use of damaged or incorrect wiring may cause this product to malfunction and/or cause
an electrical re.
• Remember that this product operates at extremely high voltages. Make sure your hands
and work area are clean and dry to avoid injury from electrical shock.
• Leave at least 1/8" clearance between the lamps and the front spoiler, as the heat may
damage the spoiler.
WARNING
• This product generates high voltages and is very dangerous. For installation, always
contact one of the PIAA authorized dealers.
• This lamp should only be mounted in the upright position. The PIAA logo should be read
right side up.
• For maximum lamp function, always use the PIAA relay harness (PN 34035).
• Do not disassemble or alter the lamp itself and/or the controller. Also do not open the
cover, disassemble, or alter the relay harness unless the fuse inside the relay unit needs
to be replaced. Overheating, short circuit, or vehicle re could occur by disassembly or
alteration. We are not responsible for any trouble due to alteration.
• When removing/installing the connector, hold the connector to securely remove/install.
If not securely connected, the lamp will not light up and other problems may occur.
WARNING
2
CONTENTS
* Make sure that all parts are in the package. If something is missing, please contact the
store where you purchased the product.
Philips-head screwdriver
TOOLS
Flat-head screwdriver 8mm/19mm wrench
Diagonal cutters Pliers Box wrench
Ornament remover Black sealer
3
One (1) Lamp assembly.
One (1) rubber cushion. One (1) Allen Wrench
4
• When using a commercially supplied lamp bracket, before removing the bolt
that is already installed on the car body, make sure that it is safe to do so.
• The lamp should be mounted in an area sucient to support its size and
weight. Failure to do so may result in excess vibration leading to shorter bulb
life and/or physical damage to the lamp or your vehicle.
• Do not attempt to install the lamp directly to any plastic part of the car body.
If the lamp needs to be installed on the plastic, reinforcement materials should
be placed on both sides of the plastic part.
• When installing, make sure the lamp body, lens, and rim are not touching the
bumper and other plastic parts. Such plastic parts might deform.
• The lamp installation surface should be at.
cAutIoN
2. Using the rubber cushion, at washer, spring washer, and nut, install the lamp to the car
ensuring the PIAA logo reads right side up.
• The lamp should be tightened to the degree that the lamp body cannot be
moved by hand.
cAutIoN
LAMP INSTALLATION
1. For lamp installation, a hole with a diameter of
14mm is required. Make necessary preparation
such as installation of lamp bracket.
Flat washer
Spring washer
Nut
Flat washer
Rubber cushion Spring washer
Nut
Orientation of logo
Tightening Torque: 30NM
When connecting the wires on the harness, follow the wiring diagram and the se-
quence below.
1. Before connecting any wires, disconnect the negative (-) battery terminal.
Note: When running the wires through the engine compartment be sure to keep
them securely away from moving parts such as the fan and the throttle cable and away
from hot parts such as the exhaust manifold.
2. Pull the connector for the relay harness switch into the car and connect it to the switch
harness.
3. Identify the best location for the switch, then attach the switch to the vehicle using the
double-sided adhesive tape (included).
4. As shown, x the relay unit with the hexagonal bolt (included) and the hexagonal nut
(included) so that the cord comes to the bottom side.
5. Connect the (+) cord (white) to the (+) cord of the side lamps by using the one-touch
connector (included).
Note: Holding the cord securely with pliers, make sure the one-touch connector is
properly closed.
6. Connect the relay harness to the controller.
7. Ground the (-) cord on the body side.
8. Connect the (+) power cord (white) and the battery (+) terminal to the battery.
9. Use the harness band (included with PN 34035) to x the relay harness to the car body
side harness so that it will not come in contact with any movable engine and/or high
temperature parts.
10. Connect the (-) power cord (black) and the battery (-) terminal to the battery.
5
HARNESS INSTALLATION
6
WIRING DIAGRAM
7
DRIVING LIGHT AIMING
Typically, driving lights are mounted above the front bumper about 14-30 inches from the
ground to provide extra high beam illumination. Driving lights can be mounted below the
bumper, although they will not be as ecient because the light will hit the ground sooner
and reduce the range of the light.
Visual aim is made with the center of the beam not spot 1.5 inches below the lamp center at
25 feet with the lamp facing straight forward (see below).
Do not use driving lights into oncoming trac.
Driving lights should never be the only forward light source.
Driving lights should only be used with the headlamp high beams.
cAutIoN
8
DISASSEMBLY
1. Pry white cover o lamp at the arrow
location on the black housing.
2. Unscrew the black (BK) frame.
3. Remove L&R&BK frame unit.
4. Unplug 2 bulb plugs.
9
5. L&R&BK frame unit...
6. Unscrew 6 screws on the L&R&BK frame unit
and take L&R unit away from the B&K frame.
(Note: No need to unscrew this if you are only
changing the bulb!)
7. Unscrew the little screws that mount the bulb.
8. Take out the bulb carefully!
10
NOTES
Tabla de contenidos
Otros manuales de Accesorios para automóviles de Piaa
