Phottix Odin TTL Manual de usuario
INSTRUCTION MANUAL
MANUEL D’UTILISATION
BENUTZERHANDBUCH
MANUAL DE INSTRUCCIONES
INSTRUKCJA OBSŁUGI
РУКОВОДСТВО ПОЛЬЗОВАТЕЛЯ
说明书
說明書
2
63
17
32
48
78
95
108
En
Fr
De
Es
Pl
Ru
CnSimp
Cn Trad
Phottix Odin TTL Flash Trigger
for Nikon
2
Parts
TransmitterControlUnit(TCU)
1. LCD Screen
2. Options Button
3. Mode Button
4. Zoom Button
5. Power Button
6. LED
7. + / - Buttons
8. Selection Buttons
9. Clear Button
10. Autofocus Assist Illuminator
(AF-ILL) Function Button
11. Modeling Light Button
12. Test Button
13. Battery Compartment
14. Locking Ring
15. Hot Shoe
16. USB port
16
14
15
13
1
34
5
7
12 9 10 11
2
8
6
3
Receiver
1. Power Switch
2. Group Selection Switch
3. 3.5mm Output Port
4. USB Port
5. 5V DC Power Port
6. Channel Selection Switch
7. LED
8. Hot Shoe Mount
9. Locking Ring
10. Cold Shoe / ¼” Tripod Lug
11. Battery Compartment
En INSTRUCTION MANUAL
7
8
3
1
2
11
10
9
6
4
5
4
Upgrading rmware by USB
After turning on the Phottix Odin TCU and
receivers, slave mode does not need to be set
on ashes on Phottix Odin receivers, but ashes
need to be set in TTL mode, Flash Zoom needs
to be set to Auto and AF ILL to ON (see your
ash manual for details).
Ensure there is a good hot shoe connection
between the TCU and camera, and ashes and
receivers for best performance.
Many TTL ashes have been tested but the
manufacturer cannot guarantee that all third
party TTL ashes will function properly with the
Phottix Odin. It has been designed and
optimized for original Nikon ashes using the
i-TTL system. Issues with third party ashes will
not be supported.
Tips: Turn o all devices – ashes/strobes,
cameras, and the Phottix Odin TCU and
receivers - when connecting and disconnect-
ing devices.
The rmware of the TCU and receivers can be
upgraded using the included USB cable. Any
upgrades and full instructions will be
announced on the Phottix Blog
(journal.phottix.com).
Please Note
Compatibility with Phottix Strato
Series Flash Triggers
The Phottix Odin TCU oers compatibility with
Phottix Strato and Phottix Strato II Multi
receivers. The Odin TCU will trigger Strato
receivers but will not transmit TTL or power
control data. Strato series receivers will work as
they previously did: With ashes set in Manual
Mode.
1. The Odin TCU set on Channel 1, 2, 3 or 4 and
in any group will trigger Phottix Strato
receivers set on Channel 1, 2, 3 or 4. Other Odin
TCU functions will not aect Strato receivers.
2. When the Phottix Odin TCU is set to Group A,
press the Test button, the Strato receivers and
the ashes on receivers will test re.
5
En INSTRUCTION MANUAL
3. The Strato II Multi receivers set to the same
channel and compatible group as the Odin TCU
will be triggered. The Odin TCU will not trigger
Strato II Multi receivers on Group D. Other Odin
TCU functions (TTL, Power control) will not
aect Strato II Multi receivers.
4. The Odin TCU set to Channel 1, 2, 3 or 4 in
TTL/Mixed mode (Group A, B and C) and in
Ratio mode (Group A and B) can be compatible
with Phottix Strato II Multi receivers on Channel
1, 2, 3 or 4 and Group A, B or C.
5. Press the Test button and ashes on Strato II
Multi Receivers will test re in sequence: Group
A, followed by Group B and C.
6. If a group is disabled on the Odin TCU in
TTL/Mixed mode, it will not trigger ashes on
Strato II Multi receivers.
6
7. Strato and Strato II Multi transmitters will not
trigger Odin receivers.
8. Phottix Odin for Nikon TCUs will not trigger
Odin for Canon Receivers.
9. Using the Odin TCU in HSS mode may cause
issues with ash sync when using Strato and
Strato II Multi receivers. Inserting batteries
1. Press the battery cover in while pushing it
away from the Phottix Odin TCU or receiver.
The battery cover will slide open.
2. Remove the battery cover.
3. Insert AA batteries as shown.
4. Replace the battery cover and push back into
the locked position.
5. When the battery power icon on the TCU
shows low battery levels please change the
batteries.
The LED on the TCU and receiver units will
turn green when the camera is focusing and
red when a photo is being taken.
Pressing any button on the TCU will turn on the
LCD Backlight for approximately 10 seconds. If
no further buttons on the TCU are pressed the
light will go o.
Pressing the Modeling Light Button on the TCU
will cause all ashes attached to Odin receivers
to ash for one second. This is useful as a
preview of lighting set-ups or for assist-focus.
LED functions
Using the LCD Backlight
Using the Modeling Light Button
Turning the TCU and receiver on/o
Groups and Channels
The TCU
Connecting to the camera hot shoe
1. To turn on the Phottix Odin TCU: Press and
hold the Power Button until an image appears
on the LCD screen.
To turn o: Press and hold the Power Button
until the LCD screen goes blank.
2. To turn on the Phottix Odin receiver: Move
the power switch to the “ON” position.
To turn o the receiver by moving the power
switch to the “OFF” position.
1. The Phottix Odin System has 3 groups: A, B,
and C, and 4 transmission channels: 1, 2, 3, 4.
2. Receivers can be assigned both group and
channel designations.
3. The TCU will allow EV, Power Level and Zoom
setting adjustments to be set for each group of
receivers set to same channel (if the group is
not disabled on the TCU)
1. Turn o the camera.
2. Slide the Odin TCU into the camera’s hot
shoe mount.
7
En INSTRUCTION MANUAL
6. When the battery power on receivers is very
low, the LED will ash red light every 2 seconds.
Please change the batteries.
Functions
To change function screens
TTL/Mixed Functions Screen
8
3. Turn the TCU locking ring until tight.
4. Turn on the Odin TCU.
5. Turn on the camera.
The TCU has two main function screens:
TTL/Mixed Function Screen and Ratio.
TTL/Mixed allows groups A, B and C to be set to
TTL, Manual or OFF individually with
adjustments to Zoom, EV level or power level.
Ratio allows groups A and B can be set from 8:1
to 1:8. EV levels can also be adjusted from -3 to
+3 (similar to the Nikon iTTL system available
on some ashes).
Press the Option button on the TCU. The
Option Button will switch between TTL/Mixed
screen and Ratio screen.
The Selection Button allows you to cycle
through groups A, B, and C, and Channel
selections. Active selections will ash on the
LCD.
1. The - / + buttons will change the EV
adjustments or Power Level while groups A, B
or C are selected.
2. The - / + buttons will change the transmis-
sion channel (1, 2, 3 or 4) when Channel is
selected. This will change the channel the TCU
uses to transmit.
9
TTL / M / O Ratio Functions Screen
While groups A, B or C are selected, pressing
the Mode button will change from TTL, (M)
Manual, or O functions.
TTL: Will re ashes using TTL metering. The
EV level of each group can be adjusted up or
down (see above).
M: Flashes are set in Manual mode and power
levels adjusted up or down (see above).
O: Selecting O (signied by three
underscores _ _ _) will turn o the selected
group and not re any remote ashes in that
group.
The Selection Button allows you to cycle
through A:B ratio adjustments, EV adjustments
and Channel selections.
Press the Selection button to access Ratio
adjustments. Press the + / - button until the
desired A:B ratio is achieved.
Pressing the Selection button again will move
the active selection to the EV adjustment
section. Press the + / - button until the desired
EV level is achieved.
The Selection Button can also be used to
navigate to the Channel icon. The - / + buttons
will change the transmission channel (1, 2, 3 or
4) when Channel is selected. This will change
the channel the TCU uses to transmit.
Fast Exit
Pressing the TCU Power Button after making
changes to settings will exit edit mode. The
TCU will save the current settings.
En INSTRUCTION MANUAL
10
Fast Exit
Pressing the TCU Power Button after making
changes to settings will exit edit mode. The
TCU will save the current settings.
Fast Exit
Pressing the TCU Power Button after making
changes to settings will exit edit mode. The
TCU will save the current settings.
1. Press the Zoom Button to enter the Zoom
screen – this functions the same in TTL/Mixed
or Ratio Modes.
Adjusting ash zoom
Using the Zoom Function
The Phottix Odin allows the zoom level of
ashes to be set wirelessly. Zoom can be set as
TTL or Manual.
TTL Zoom: Flash zoom setting will change
dynamically as a camera zoom ring is adjusted.
Manual Zoom: Flash zoom can be set to a xed
value on the TCU. Any changes made to
camera zoom will not aect this setting.
2. Pressing the Selection button will cycle
through groups A, B and C, and Transmission
channel.
3. With groups A, B or C active: Press the Mode
Button to change from TTL to Manual mode. In
Manual Zoom, press the - / + buttons to adjust
the ash zoom. No adjustments can be made in
TTL mode.
Note: Pressing the Selection button after the
CH selection will return to the TTL/Mixed or
Ratios Function Screen.
Otros manuales para Odin TTL
1
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Idiomas:
