Photron FASTCAM Multi Manual de usuario

The copyright of this manual is held by PHOTRON LIMITED.

Product specifications and manual contents are subject to change without notice.

PHOTRON LIMITED bears no responsibility for any results by using our products nor by applying this manual to any operations.

WARNING

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the users will be required to correct

the interference at their own expense.

CAUTION:

Any changes or modifications not expressly approved by the party responsible for compliance

could void the user's authority to operate the equipment.

Introduction

Thank you for your purchase of Photron’s high-speed camera system, the “FASTCAM Multi” (referred to

below as the system).

This manual contains the operating instructions and warnings necessary for using the system.

Before using the system, please read the entire manual.

If any part of this manual is unclear, contact Photron using the contact information printed at the back of

the manual.

After you finish reading the manual, store it in a safe place along with the warranty card and refer back to

it when necessary.

Manual Notation

The following icons and symbols are used in the explanations in this manual.

Icon/Symbol

Description

This symbol indicates content that should always be read.

This symbol indicates instructions that should always be

followed when using the software, or things to be careful of

when using the software.

This symbol indicates supplementary items to be aware of

when using the system.

This symbol indicates the location of a reference.

This symbol indicates a space for you to make notes.

“ “

This symbol is used to indicate the names of items on a

screen, references, dialog names, and connectors.

［］

This symbol is used to indicate menu names, and sub-menu

names.

Using the Manual

This section explains the layout of the manual. For other options, please refer to each manual.

Introduction

The introduction explains the manual and safety precautions.

Chapter 1. Overview

This chapter gives an overview of the system and an explanation of its features.

Chapter 2. Setup

This chapter gives an overview of the components that make up the system. It also explains a list of items that

should be checked before using the system.

Chapter 3. System Connections

This chapter explains the procedure for connecting each component of the system and to a PC.

Chapter 4. Functions

This chapter explains the system’s functions. Refer to the “Photron FASTCAM Viewer User’s Manual” for

additional details on using a PC to control the system.

Chapter 5. Product Specification

This chapter explains the system’s specifications.

Chapter 6. Warranty

This chapter explains about the warranty.

Chapter 7. Contacting Photron

This chapter lists the contact information to use when contacting Photron if the system malfunctions or if a

portion of the manual is unclear.

Using the System Safely and Correctly

In order to prevent injury to yourself and others, and toprevent damage to property, carefullyobserve the

following safety precautions.

Photron has given its full attention to the safety of this system. However, the extent of damage and injury

potentially caused by ignoring the content of the safety precautions and using the system incorrectly is

explained next. Please pay careful attention to the content of the safety precautions when using the

system.

This symbol indicates actions that carry the risk that a person could receive a

serious injury.

This symbol indicates actions that carry the risk that a person could receive a

moderate injury, or that damage to physical property might occur.

The safety precautions to be observed are explained with the following symbols.

This symbol indicates actions that require caution.

This symbol indicates actions that are prohibited and must be avoided.

This symbol indicates actions that must always be performed.

Caution

Warning

■ Do not perform actions that will damage the AC cable or plug.

(Do not damage the cable, modify it, use it near a heater, excessively bend, twist or pull on it,

place heavy objects on it, or bundle it.)

Using the cable when damaged can cause fire, electric shock, or a short circuit.

■ Do not use the system in a manner which will exceed the rating of the power outlet or wiring

equipment used.

Exceeding the power rating might cause a fire from excessive heat.

■ Do not insert metallic objects inside, or pour liquids such as water on, the system.

Doing so can cause fire, electric shock, or malfunction from short circuit or heat.

■ Do not disassemble or modify the system.

There are high voltages inside the system that can cause electric shock.

■ Do not plug in or unplug the power cord with wet hands.

Doing so can cause electric shock.

■Make sure the power plug is fully insert into the socket .

Not fully plugging in the power cable can cause fire from electric shock or heat.

■ When something is wrong with the system, unplug the power cable immediately.

- When a foreign substance or liquid, such as metal or water, gets inside.

- When the outer case is broken or damaged, such as from a fall.

- When the system produces smoke, a strange smell, or strange sound. Using the system in

these conditions might cause a fire or electric shock.

■Do not use the accessories by the usage that a manufacturer does not specify. It may cause

damage of protection.

Warning

■ Always unplug the system when cleaning it or when it is unused for a long period of time.

Leaving or storing the system connected to the power source might cause fire from insulation

deterioration or electrical discharge.

■Please consult us in advance when you perform an event by which laser light or direct rays fall

on the image sensor surface.

■ Do not set the system in a location where the temperature gets unusually hot.

The trunk and inside of a car can get especially hot in summer.

Doing so can cause the outer case and internal components to deteriorate or cause a fire.

■ Do not place the system in a location prone to oily smoke or steam, or in a location with a lot of

humidity or dust.

Oil, moisture, and dust conduct electricity, which can cause a fire or electric shock.

■ Do not obstruct the air intake and exhaust port, when the system is installed.

■ Ambient temperature 0-45° C, humidity 80% RH or lower, maximum altitude 2,000m or lower.

In addition, if exceeding these limits, use in a condensation-free environment.

Use in a condition out of the above limits can cause malfunction.

■ Do not store the equipment in a location where the temperature goes below -20°C or higher

than 60°C. Also, prevent condensation from forming during shipment.

■ When shipping, remove the connecting cable and use the original packaging or a dedicated

carrying case.

Do not ship the equipment in an environment where the temperature goes below .

-20°C or higher than 60°C. Also, prevent condensation from forming during shipment.

■The rubber foot used in this product might be hydrolyzed if it is stored or used in a high

humidity environment for a long time.

Moreover, it might be hot melted if it is stored or used in a high temperature environment

for a long time.

Caution

“CE” mark indicates that this product complies with the European requirements for safety,

health, environment and customer protection. “CE” mark equipments are intended for sales in

Europe.

These symbols indicate that this product is not to be disposed of with your household waste,

according to the WEEE Directive (2002/96/EC), the Battery Directive (2006/66/EC) and/or your

national laws implementing those Directives.

This product should be handed over to a designated collection point, e.g., on an authorized

one-for-one basis when you buy a new similar product or to an authorized collection site for

recycling waste electrical and electronic equipment (EEE) and batteries and accumulators.

Improper handling of this type of waste could have a possible impact on the environment and

human health due to potentially hazardous substances that are generally associated with EEE.

Your cooperation in the correct disposal of this product will contribute to the effective usage of

natural resources.

For more information about the recycling of this product, please contact your local city office,

waste authority, approved scheme or your household waste disposal service or visit

www.photron.com.

(EEA: Norway, Iceland and Liechtenstein)

This product is in conformity with the protection requirements of EU Council Directive

2014/30/EU (Class A) on the approximation of the laws of the Member States relating to

electromagnetic compatibility.

Warning: This is a Class A product. In a domestic environment, this product may cause radio

interference, in which case the user may be required to take adequate measures.

European Union (and EEA) only

Electrostatic Discharge (ESD) events may cause immediate and unrecoverable damage to the

image sensor. Please read the following instructions and take EXTREME CARE when cleaning the

image sensor surface.

■ ALWAYS take appropriate anti-static precautions when cleaning or working near the Image

sensor.

■ DO NOT use any form of cleaning equipment using electrostatic or ‘charged fiber’ technology.

■ Please discharge any electrostatic build up in your body by touching a grounded metallic

surface before working near the camera sensor.

■ Very gently, use only clean and dry air to remove dust from surface of the image sensor.

■ To remove stubborn contamination use the highest grade (e.g. VLSI grade) pure Isopropyl

alcohol (IPA) with optical wipes of ‘clean room’ grade.

■ Extreme care must be taken! Gently wipe across the sensor in a single action.

(DO NOT rub to avoid abrasive damage to delicate optical coatings on the glass surface.)

Cleaning of the Image Sensor Surface

■Minimum curve radius of the camera cable is 125mm. Be careful when using or storing camera

cable to give an ample space for the curvature.

■Do not give an excessive impact or load to camera cables to avoid damage.

■Whenever the cables are out of use, place the attached connector caps for protection of the

connectors.

■In operation, connect the main unit’s connector cap and the camera cable’s connector cap

each other to avoid dirt and pollution and to keep clean inside.

The camera cable includes optics fibers. If dust or dirt is in inside of a connector, it may cause a

communication error. Keep clean the inside of connectors. If a connector is polluted, clean the fiber

edges by following instruction or using the bundled cleaning kit.

■DO NOT use hard and/or sharp materials for cleaning.

■Very gently, use only clean and dry air to remove dust from surface of the image sensor.

■To remove stubborn contamination use the highest grade (e.g. VLSI grade) pure Isopropyl

alcohol (IPA) with optical wipes of ‘clean room’ grade.

■Fibers are indicated with a red circle over the cable cross-section.

Camera Cable

Otros manuales para FASTCAM Multi

Tabla de contenidos

Otros manuales de Cámara digital de Photron

Photron

Photron FASTCAM-PCI Manual de usuario

Photron

Photron FASTCAM Mini GigabitEthernet Interface Manual de instrucciones

Photron

Photron FASTCAM SA-Z Manual de usuario

Photron

Photron FASTCAM Mini WX50 Manual de usuario

Photron

Photron Fastcam APX RS Manual de instrucciones

Photron

Photron FASTCAM ultima SE Manual de usuario

Photron

Photron FASTCAM Multi Manual de usuario

Photron

Photron Fastcam SA3 Manual de usuario

Photron

Photron FASTCAM MH6 Manual de usuario

Photron

Photron FASTCAM Mini Series Manual de usuario

Photron

Photron FASTCAM Mini AX100 Manual de usuario

Photron

Photron FASTCAM Multi Manual de usuario

Photron

Photron Fastcam SA2 Manual de usuario

Photron

Photron FASTCAM ultima APX-i2 Manual de usuario

Photron

Photron FASTCAM Nova Manual de usuario

Photron

Photron FASTCAM ultima 1024 Manual de usuario

Photron

Photron IDP-Express R2000 Manual de usuario

Photron

Photron FASTCAM SA8 Manual de usuario

Photron

Photron FAST Dock Manual de usuario

Photron

Photron FASTCAM Mini WX50 Manual de usuario

Photron

Photron FASTCAM SA-X2 Manual de usuario

Photron

Photron Fastcam SA5 Manual de usuario

Photron

Photron FAST Drive Manual de usuario

Photron

Photron Fastcam MC1 Manual de usuario

Manuales populares de Cámara digital de otras marcas

Mercury

Mercury 350K Manual de usuario

Pentax

Pentax Optio LS 465 Manual de usuario

Sanyo

Sanyo VPC-S1085 Manual de usuario

GE SMART A1255 Manual de usuario

Point Grey

Point Grey Gazelle Manual de usuario

Nikon

Nikon COOLPIX A Manual de usuario

Pentax

Pentax P-5 Manual de usuario

BlazeVideo

BlazeVideo A280 Manual de usuario

Sony

Sony MCA-20 Manual de usuario

Sony

Sony Alpha DSLR-A290 Manual de usuario

ATIK Cameras

ATIK Cameras One Manual de usuario

CohuHD Costar

CohuHD Costar 3930 Series Manual de usuario

Leica

Leica M10-R Manual de usuario

FujiFilm

FujiFilm FinePix A700 Manual de usuario

Lorex

Lorex LNZ81P25 Series Manual de usuario

GE J1470S Manual de usuario

Sony

Sony A6700 Guía del usuario

Canon

Canon EOS ELAN7 Manual de usuario