Phoenix Mecano Dewert Okin CU458-2 Manual de usuario

CONTROL UNIT CU458-2

Installation Instructions

(Translation of the original installation instructions)

CU458-2 Foreword

93728 1.0 3

Foreword

Document revision history

Version Date Modification, change

1.0 03/2020 First release

Disclaimer and exclusion of liability

DewertOkin is not responsible for damage resulting from:

•failure to observe these instructions,

•changes made to this product which have not been approved by DewertOkin, or

•the use of replacement parts which have not been approved or manufactured by DewertOkin.

We reserve the right to make unannounced technical changes in the course of our continual

product improvement process!

Creation of a complete operating instruction manual for the entire end product

These instructions are only intended to be used by the end-product manufacturer. They should not

be given to the operator of the end product. The factual information contained within may be used

as a basis when creating the end-product manual.

The warning and danger notices are best suited for use in the end product's manual. However, it is

not sufficient to simply follow these notices. You should also carry out an internal risk assessment

for your end product. This can then be used as the basis for the safety notices in your manual.

These installation instructions do not contain all information required to safely operate the end

product. They only describe the installation and operation of the product as partially completed ma-

chinery.

The instructions are intended for the technicians responsible for manufacturing an end product and

not for the operators of the end product.

Table of Contents CU458-2

4 93728 1.0

Table of Contents

Foreword 3

Document revision history 3

Disclaimer and exclusion of liability 3

Creation of a complete operating instruction manual for the entire end product 3

Table of Contents 4

1. General Information 5

1.1 Configurations 5

1.2 About these installation instructions 5

1.3 Conventions used 5

2. Safety notices 6

2.1 Proper and intended usage 6

2.2 Selection and qualification of personnel 7

2.3 Ratings plate 8

3. Possible combinations 9

4. Description 10

4.1 Components 10

5. Technical specifications 11

6. Installation 13

6.1 Safety notices to observe during installation 13

6.2 Installation procedure 13

7. Information about creating your Operating Manual 16

7.1 General information 16

7.2 Configuring the hand-held remote and app 17

8. Troubleshooting 19

9. Maintenance 20

9.1 Cleaning and care 20

10. Disposal 21

10.1 Packaging material 21

10.2 Components in the control unit 21

Additional information 22

CU458-2 General Information

93728 1.0 5

1. General Information

1.1 Configurations

The designation CONTROL UNIT is used in these installation instructions to refer to the CONTROL

UNIT CU458-2.

1.2 About these installation instructions

In order to install the CONTROL UNIT successfully and safely in the end product, these installation

instructions must be observed. These instructions are not an operating manual for the end product.

These instructions will help you to minimize danger, repair costs and down times. They will also

help you to increase the reliability and lifespan of the device.

CAUTION

The notices in these instructions must be followed! Following the guidelines during installation

and connection procedures will help to minimize:

•the risk of accident and injury, and

•damage to the CONTROL UNIT or the end product.

These installation instructions have been written with due care and attention. However, we cannot

guarantee that the data, images and drawings are complete and correct nor do we accept any lia-

bility for the information contained therein, unless required by law.

1.3 Conventions used

Notices which do not relate to safety are indicated in these instructions with a symbol:

Triangular notice symbol

Explanations of warning notices

CAUTION

CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moder-

ate injury.

NOTICE

NOTICE is used to address practices which are not related to personal injury but may result in

damage to the product or surroundings.

Safety notices CU458-2

6 93728 1.0

2. Safety notices

2.1 Proper and intended usage

The CONTROL UNIT is intended for use:

•as a control unit for suitable DewertOkin drive systems,

•for HOME applications (in beds, reclining chairs, etc.).

CAUTION

Risk of accident

This CONTROL UNIT should only be used for the applications described above. Any other use

is forbidden. Improper usage can lead to accidents or destruction of the unit. Such non-approved

applications will lead immediately to the expiration of all guarantee and warranty claims on the

part of the end-product manufacturer against the manufacturer.

2.1.1 Improper usage

Be sure to follow the notices below concerning improper usage. You should include them in your

product manual in order to inform the users of your end product.

The CONTROL UNIT should not be used:

•in any environment where combustible or explosive gases or vapours (e.g., anaesthesiology)

may be present,

•in the proximity of open fires or other heat sources (such as furnaces, ovens or direct sunlight),

•as a power source for toys or games,

•in any application that will be cleaned with an automated washing system,

•in a moist environment, or

•outdoors.

The CONTROL UNIT can be used by children of 8 years and older, persons with reduced physical,

sensory or mental capabilities, or persons with lack of experience or knowledge when they are su-

pervised or instructed concerning the safe use of the device and when they understand the result-

ing risks. Do not allow children to play with this device. The cleaning and user maintenance must

not be carried out by children without supervision.

You should only use spare parts which have been manufactured or approved by DewertOkin.

Only these parts will guarantee a sufficient level of safety.

CU458-2 Safety notices

93728 1.0 7

2.2 Selection and qualification of personnel

The installation of the CONTROL UNIT in the end product may only be performed by qualified per-

sonnel.

2.2.1 Electrical safety

CAUTION

Electric shock

Be careful; there is a risk of electrical shock! Before installing, make sure that you disconnect the

external DewertOkin power supply for the CONTROL UNIT from the power outlet!

The CONTROL UNIT should not be used! You must properly dispose of malfunctioning or broken

units.

2.2.2 Floor (under-bed) lighting

The CONTROL UNIT is equipped with two floor (under-bed) LEDs.

CAUTION

Do not look straight into the LED and do not aim the LED at persons.

Safety notices CU458-2

8 93728 1.0

2.3 Ratings plate

The ratings plate shown is an example; The specifications for your CONTROL UNIT may differ

from this illustration.

Figure 1 Ratings plate for the CONTROL UNIT (example)

CU458-2 Model name

xxxxx Article number

Model No. Model number

24 – 29 V 6.00 A Input voltage and current consumption

Duty cycle: 2 min ON / 18 min OFF Intermittent operations: 2 minutes / 18 minutes

Prod. Date Calendar week / year

2.4GHz Radio frequency

Serial No. Serial number

FCC ID: O3YCU458-2 Federal Communications Commission ID

IC:10744A-CU4582 Industry Canada identifier

IP20 Protection degree

Use in dry rooms only!

Always follow the instructions in the manual!

Follow all special disposal instructions!

CU458-2 Possible combinations

93728 1.0 9

3. Possible combinations

The CONTROL UNIT can be used together with multiple drives, vibration motors and accessories

that have been approved by DewertOkin.

A tailored system consists of the combination of control unit, drive, vibration motor, accessories,

and hand-held remote.

DewertOkin has separate system instruction manuals containing the additional information and in-

structions needed for these systems.

Detailed information on combination possibilities can be requested directly from DewertOkin.

Description CU458-2

10 93728 1.0

4. Description

The CONTROL UNIT is a control unit and for one or more DewertOkin vibration motors. An exter-

nal DewertOkin power supply unit is used to connect the CONTROL UNIT to the mains power.

4.1 Components

The housing of the CONTROL UNIT has a connection for an external DewertOkin drive system,

as well as connections for vibration motors and various accessories. Multiple drives (e.g. the Del-

ta drive and Alpha drive) and vibration motors can be connected to the CONTROL UNIT.

Figure 2 Connections and ports on the CONTROL UNIT CU458-2

A CONTROL UNIT CU458-2

B Port for vibration motor

C Port for vibration motor

D Port for supply voltage to drives

E Floor (under-bed) lighting

F Multi-functional port (MFP)

G Port for accessories

H Port for accessories

I Power LED (lights up whenever the

CONTROL UNIT is connected to power)

J Reset button / Pairing button

K Pairing LED

Tabla de contenidos

Otros manuales de Unidad de control de Phoenix Mecano

Phoenix Mecano

Phoenix Mecano DewertOkin CU155 Manual de usuario

Phoenix Mecano

Phoenix Mecano Dewert Okin HE-300 SMPS Manual de usuario

Phoenix Mecano

Phoenix Mecano Dewert Okin HE200 Manual de usuario

Phoenix Mecano

Phoenix Mecano DewertOkin MC11 Manual de usuario

Phoenix Mecano

Phoenix Mecano Dewert Okin SG 300 Manual de usuario

Phoenix Mecano

Phoenix Mecano Dewert Okin ACCUCONTROL 4.5 Manual de usuario

Phoenix Mecano

Phoenix Mecano Okin Refined CB3432 Manual de usuario

Phoenix Mecano

Phoenix Mecano DewertOkin MC10 Manual de usuario

Phoenix Mecano

Phoenix Mecano DEWERT OKIN IPROXX 2 Guía del usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario