Philips Micro Pure WP3811 Manual de usuario
WP3811,WP3810
2
3
1
4
WP3811,WP3810
ENGLISH 6
PORTUGUÊS DO BRASIL 17
6
Introduction
Congratulations on your purchase and welcome to Philips! To fully benet
from the support that Philips offers, register your product at www.philips.
com/welcome.
General description (Fig. 1)
AFilter cartridge
B Water purier housing
CWater selection lever
DStainless steel screen
ERubber washer
FAdapter
1 A-type
2 B-type
3 C type
4 D-type
GAttachment nut
HFiltered water outlet
I Unltered water inlet
J Hollow bre
KGranular activated carbon
Important
Read this user manual carefully before you use the water purier and
save it for future reference.
Warning
The water purier is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they have been given
supervision or instruction concerning use of the water purier by a
person responsible for their safety.
Children should be supervised to ensure that they do not play with
the water purier.
-
-
ENGLISH
Do not let water hotter than 50°C run through the water
purier, this may cause damage.
Do not let the water purier freeze.
Before daily use
To prevent quick clogging of the lter cartridge, let the water run at
the unltered setting for around 5 seconds before every use.
If the water is highly coloured or turbid due to work on your water
network, do not let the water run at the ltered setting until the
water is clear.
Cautions:
1 Let the water run at the ltered setting for 10 seconds before use
each day.
2 Let the water run at the ltered setting for 60 seconds before use if
you have not used the water purier for more than two days.
3 If you have not used the water purier for more than two weeks, let
the water run at the ltered setting for 2-3 minutes before use. If the
lter cartridge emits an unpleasant smell, replace it with a new one.
Applications
Only use the water purier to lter water that meets drinking water
standards.
Do not block the ltered water outlet or connect other devices to it.
If the water pressure is very high, reduce the water ow of the tap to
prevent damage to the cartridge.
Keep the water purier away from heat to avoid distortion or
breakage.
Do not tamper with the water purier.
Do not remove the lter cartridge while you use the water purier
Do not use the water purier without a lter cartridge.
Do not place the water purier near a window where it is exposed
to direct sunlight.
This water purier does not soften water.
Do not use ltered water in aquariums. Tap water, ltered or
unltered, can be harmful to sh.
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
ENGLISH 7
Do not store puried water to avoid contamination. Air contact
contaminates puried water quickly. If you want to store puried
water, use a clean container and keep it in the refrigerator. Do not
keep it in the refrigerator longer than 1 day to avoid contamination.
Features
Philips’ multi-ltration system consists of a primary lter, a secondary
lter, a high-tech hollow-bre membrane lter and a granular
activated carbon lter.
The hollow bre membrane contains 520 billion micropores
(WP3811) or 400 billion micropores (WP3810) that are small
enough to remove particles down to 0.1µm. It eliminates 99.99%* of
bacteria, rust and other particles larger than the micropore size
from your tap water without removing calcium, magnesium and other
minerals that are vital to your body. (* tested according to Japanese
Water Purier Association (JWPA) standard).
The granular activated carbon removes the unpleasant chlorine smell
and taste from your tap water.
Apart from the recommended cartridge lifetime, Philips’ unique
cartridge replacement indicator helps you determine when to replace
the lter cartridge.
Preparing for use
Before installation
Before you install the water purier, make sure all tap-mounting
adapters you require are present.
The tap must have a diameter of 13mm-25mm.
Determine what type of tap you have and select the appropriate
adapter.
The adapters supplied make the water purier suitable for almost
any kitchen tap. However, the water purier may not t some
uncommon types of taps.
The tap water pressure has to be between 0.7kgf/cm² (7 metres of
water column) and 3.5kgf/cm² (35 metres of water column). If you
use the water purier at a water pressure outside this range, either
-
-
-
-
-
-
-
-
-
-
ENGLISH8
the ltered water ow will be extremely low or the water purier
will get damaged.
Installation A-type adapter
For taps with a round spout with a diameter of 16mm, 17.5mm or
19mm (Fig. 2).
1 Remove the attachment nut and the adapter from the water
purier housing (Fig. 3).
2 Pass the attachment nut over the tap spout (Fig. 4).
3 Place the matching adapter (A-type) over the tip of the spout. The
16mm adapter is packed with the water purier. Replace it with
the 17.5mm adapter or 19mm adapter to t the diameter of your
tap (Fig. 5).
4 Screw the attachment nut rmly onto the water purier
housing (Fig. 6).
Installation B-type adapter
For taps with an aerator (threaded on the outside) (Fig. 7).
1 Remove the attachment nut and the adapter from the water
purier (Fig. 8).
2 Remove the aerator cap from the tap and pass the attachment nut
over the spout. Take out the original adapter and screw the
matching adapter (B-type) onto the tap (Fig. 9).
3 Tighten the adapter further with a coin (Fig. 10).
4 Firmly screw the attachment nut onto the water purier
housing (Fig. 11).
Installation C-type adapter
For taps with an aerator (threaded on the inside) (Fig. 12).
1 Remove the attachment nut and the adapter from the water
purier housing (Fig. 13).
-
-
-
ENGLISH 9
2 Remove the aerator cap from the tap. Take out the original adapter
and screw the matching adapter (C-type) onto the tap through the
attachment nut. (Fig. 14)
3 Tighten the adapter further with a coin (Fig. 15).
4 Firmly screw the attachment nut onto the water purier
housing (Fig. 16).
Installation D-type adapter
For taps other than A, B or C. (Fig. 17)
1 Remove the attachment nut and the adapter from the water
purier housing (Fig. 18).
2 Take out the original adapter and screw the D-type adapter onto
the water purier housing. (Fig. 19)
3 Push the water purier housing onto the tap from below and
tighten the 4 screws evenly (Fig. 20).
4 Screw the attachment nut rmly onto the water purier
housing (Fig. 21).
Make sure the rubber washer is rmly pushed against the tap to prevent
water leakage.
Installing the lter cartridge
1 Make sure the tap is closed.
2 Set the water selection lever to the unltered stream
position (Fig. 22).
3 Tilt the lter cartridge 90° backwards and insert it into the water
purier housing. (Fig. 23)
4 Pull the cartridge upwards until it is in upright position. (Fig. 24)
5 Air trapped inside the lter cartridge affects the ow rate of the
ltered water. To avoid this, slightly open the tap and let water run
through the lter cartridge for 30 seconds. The slow water ow
forces out any air that is trapped inside the lter.
-
ENGLISH10
Otros manuales para Micro Pure WP3811
4
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Idiomas:
Otros manuales de Sistema de filtración de agua de Philips
Philips
Philips Pure Taste WP3861 Manual de usuario
Philips
Philips WP4161/90 Manual de usuario
Philips
Philips AWP1775 Manual de usuario
Philips
Philips WP3812 Micro X-Pure Manual de usuario
Philips
Philips AC4012 Manual de usuario
Philips
Philips GoZero Manual de usuario
Philips
Philips Micro Pure WP3811 Manual de usuario
Philips
Philips AUT7006 Manual de usuario
Philips
Philips WP3810 Manual de usuario
Philips
Philips AUT2015 Manual de usuario
Philips
Philips AC4143 Manual de usuario
Philips
Philips AUT3234 Manual de usuario
Philips
Philips WP3890/01 Manual de usuario
Philips
Philips AWP1811 Manual de usuario
Philips
Philips AC4142 Manual de usuario
Philips
Philips WP3892/01 Manual de usuario
Philips
Philips WP3822 Micro X-Pure Manual de usuario
Philips
Philips AWP2980 Manual de usuario
Philips
Philips HD3802 Manual de usuario
Philips
Philips AWP3703 Manual de usuario
