Philips HD3802 Manual de usuario
HD3802
2
1
3
6
7
8
9
12
5
2
1
3
4
18
19
17
16
13
11
10
22
21
20
14
15
AD
B C
4
HD3802
ENGLISH 6
繁體中文 18
6
Introduction
Congratulations on your purchase and welcome to Philips! To fully benet
from the support that Philips offers, register your product at www.philips.
com/welcome.
General description (Fig. 1)
1 Filter housing
2 Filtered water outlet
3 Swivel arm
4 Filter cover
5 Hose
6 Attachment nut
7 Tap adapter (A-type 16mm)
8 Rubber washer
9 Stainless steel screen
10 Hose joint
11 Water selection lever
12 Water selection unit
13 Suction cups on bottom
14 Fasteners
15 Tap adapters
AA-type
BB-type
CC-type
DD-type
16 Unltered water inlet
17 Granular activated coral
18 Granular activated carbon
19 Hollow bre
20 Swivel nozzle
21 Filtered stream (turn nozzle clockwise)
22 Filtered spray (turn nozzle anticlockwise)
ENGLISH
Important
Read this user manual carefully before you use the water purier and
save it for future reference.
Warning
This water purier is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a
person responsible for their safety.
Children should be supervised to ensure that they do not play with
the water purier.
Do not let water hotter than 50°C run through the water purier, as
this may damage the water purier.
Do not let the water purier freeze.
Before daily use
To prevent quick clogging of the lter cartridge, let the water run at
the unltered setting for around 5 seconds before every use.
If the water is highly coloured or turbid due to work on your water
network, do not let the water run at the ltered setting until the
water is clear.
Cautions:
1 Let the water run at the ltered setting for 10 seconds before use
each day.
2 Let the water run at the ltered setting for 60 seconds before use if
you have not used the water purier for more than two days.
3 If you have not used the water purier for more than two weeks, let
the water run at the ltered setting for 2-3 minutes before use. If the
lter cartridge emits an unpleasant smell, replace it with a new one.
During use
Only use the water purier to lter water that meets drinking water
standards.
Do not block the ltered water outlet or connect other devices to it.
-
-
-
-
-
-
-
-
-
ENGLISH 7
If the water pressure is very high, reduce the water ow of the tap to
prevent damage to the cartridge.
Keep the water purier away from heat to avoid distortion or
breakage.
Do not tamper with the water purier.
Do not remove the lter cartridge while you use the water purier
Do not use the water purier without a lter cartridge.
Do not place the water purier near a window where it is exposed
to direct sunlight.
This water purier does not soften water.
Do not use ltered water in aquariums. Tap water, ltered or
unltered, can be harmful to sh.
Do not store puried water to avoid contamination. Air contact
contaminates puried water quickly. If you want to store puried
water, use a clean container and keep it in the refrigerator. Do not
keep it in the refrigerator longer than 1 day to avoid contamination.
Features
Philips’ multi-ltration system consists of a primary lter, a secondary
lter, a high-tech hollow-bre membrane lter, a granular activated
carbon lter and a granular activated coral lter.
The hollow bre membrane contains more than 1200 billion
micropores that are small enough to remove particles down to
0.1µm. It eliminates 99.99%* of bacteria, rust and other particles
larger than the micropore size from your tap water without removing
calcium, magnesium and other minerals that are vital to your body. (*
tested according to Japanese Water Purier Association (JWPA)
standard).
The granular activated carbon removes unpleasant chlorine smell, bad
taste and odours from your tap water.
The granular activated coral enriches your ltered water with natural
minerals to improve the taste and to make it healthier.
The 360° swivel arm and the swivel nozzle provide ultimate control
of the ltered water ow.
-
-
-
-
-
-
-
-
-
-
-
-
-
-
ENGLISH8
Preparing for use
Mounting the water selection unit
When you exchange the adapter, beware the screw thread of the tap is
sharp.
Before you install the water purier, make sure all tap adapters you
require are present.
The tap must have a diameter of 13mm-25mm.
Determine what type of tap you have and select the appropriate
tap adapter.
The tap adapters supplied make the water purier suitable for almost
any kitchen tap. However, the water purier may not t some
uncommon types of taps.
The tap water pressure has to be between 0.7kgf/cm² and 3.5kgf/cm².
If you use the water purier at a water pressure below this range, the
ltered water ow is either extremely low or there is no ow at all.
On the other hand, if the water pressure exceeds this range, the
water purier gets damaged.
Installation A-type adapter
For taps with a round spout with a diameter of 16mm, 17.5mm or
19mm (Fig. 2).
1 Remove the attachment nut and the adapter from the water
selection unit (Fig. 3).
2 Pass the attachment nut over the tap spout (Fig. 4).
3 Place the matching adapter (A-type) over the tip of the spout.The
16mm adapter is attached to the water selection unit when you
unpack it. Replace this adapter with the 17.5mm adapter or 19mm
adapter to t the diameter of your tap (Fig. 5).
4 Tighten the attachment nut rmly onto the water
selection unit (Fig. 6).
Installation B-type adapter
For taps with an aerator (threaded on the outside) (Fig. 7).
-
-
-
-
-
-
-
ENGLISH 9
1 Remove the attachment nut and the adapter from the water
selection unit (Fig. 3).
2 Remove the aerator cap from the tap and pass the attachment nut
over the spout.Take out the original adapter and screw the
matching adapter (B-type) onto the tap (Fig. 8).
3 Tighten the adapter further with a coin (Fig. 9).
4 Tighten the attachment nut rmly onto the water selection
unit (Fig. 10).
Installation C-type adapter
For taps with an aerator (threaded on the inside) (Fig. 11).
1 Remove the attachment nut and the adapter from the water
selection unit (Fig. 3).
2 Remove the aerator cap from the tap.Take out the original adapter
and screw the matching adapter (C-type) onto the tap through the
attachment nut. (Fig. 12)
3 Tighten the adapter further with a coin (Fig. 13).
4 Tighten the attachment nut rmly onto the water selection
unit (Fig. 14).
Installation D-type adapter
For taps other than A, B or C. (Fig. 15)
1 Remove the attachment nut and the adapter from the water
selection unit (Fig. 3).
2 Screw the D-type adapter about halfway onto the water selection
unit. Make sure to leave enough room in order to tighten the tting
at a later step. (Fig. 16)
3 Push the water selection unit rmly onto the tap from below and
tighten the 4 screws evenly. Make sure that you keep the tap in the
center of the screw fastener.At the same time maintain pressure
on the water purier housing from below. (Fig. 17)
-
-
ENGLISH10
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Sistema de filtración de agua de Philips
Philips
Philips Saeco BRITA INTENZA+ Manual de usuario
Philips
Philips WP3864 Manual de usuario
Philips
Philips AC4105 Manual de usuario
Philips
Philips AWP2900 Manual de usuario
Philips
Philips AWP3753 Manual de usuario
Philips
Philips AC4141 Manual de usuario
Philips
Philips FC8038/01 Manual de usuario
Philips
Philips Saeco AquaClean CA6903 Manual de usuario
Philips
Philips Pure Taste WP3861 Manual de usuario
Philips
Philips AUT2015 Manual de usuario
Philips
Philips WP3822 Micro X-Pure Manual de usuario
Philips
Philips AC4144 Manual de usuario
Philips
Philips Pure Taste WP3861 Manual de usuario
Philips
Philips Micro Pure WP3811 Manual de usuario
Philips
Philips AUT3015 Manual de usuario
Philips
Philips Micro Pure WP3811 Manual de usuario
Philips
Philips AC4012 Manual de usuario
Philips
Philips AWP3753 Manual de usuario
Philips
Philips Pure Taste WP3861 Manual de usuario
Philips
Philips AWP2900 Manual de usuario
