Philips Dynalite DMC2 Manual de usuario
DMC2
Installation Guide
Revision 03
Area for main photograph
Area for insert photo
W: 46.1mm up to 79 mm
H: 46.1mm
X: 12.6mm absolute on page
Y: 132.6mm abs on page
This insert has a shadow
Contents
DMC2 1
1Product Overview 5
1.1 DMC2 Enclosure 6
1.1.1 Dimensions 6
1.1.2 Enclosure diagram 7
1.2 DSM2-XX 8
1.2.1 Dimensions / Diagrams 8
1.3 DMD31X Module 9
1.3.1 Dimensions 9
1.3.2 DMD31X module output wiring 10
1.4 DMP310-GL 11
1.4.1 Dimensions / Diagrams 11
1.5 DMR310 / DMR316 12
1.5.1 Dimensions / Diagrams 12
2Installation 13
2.1 Installation requirements 13
2.2 Cabling 15
2.3 Mounting the DMC2 16
2.4 Inserting and connecting modules 17
2.4.1 DCM-DyNet 19
2.4.2 DSM2-XX 20
2.4.3 Control module installation 22
2.4.4 Wiring loom 24
3Post-installation testing 25
3.1 Service LEDs and switch 25
3.2 Manual override keypad 26
DMC2 4
About this Guide
Overview
This guide is designed to assist in the installation of the DMC2 Modular Controller.
A working knowledge of Dynalite commissioning processes is required to effectively use this
document. For more information on the commissioning process, consult the DMC2
Commissioning Guide.
Disclaimer
These instructions have been prepared by Philips Dynalite and provide information on Philips
Dynalite products for use by registered owners. Some information may become superseded
through changes to the law and as a result of evolving technology and industry practices.
Any reference to non- Philips Dynalite products or web links does not constitute an
endorsement of those products or services.
Copyright
© 2019 Signify Holding. All rights reserved. Specifications are subject to change without
notice. No representation or warranty as to the accuracy or completeness of the
information included herein is given and any liability for any action in reliance thereon is
disclaimed. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke
Philips N.V. All other trademarks are owned by Signify Holding or their respective owners.
DMC2 5 Product Overview
1Product Overview
The Philips Dynalite DMC2 is a versatile modular controller that consists of a power supply
module, communication module, and up to two interchangeable control modules.
The power and communication modules are listed below:
•DSM2-XX – Single-phase or three-phase supply module that supplies power to the
communications and control modules.
•DCM-DyNet – Communications module that supports DyNet, DMX Rx, dry
contact inputs and UL924 input.
A variety of control modules provide simultaneous control of multiple load types and
capacities:
•DMD – Driver control module for 1-10V, DSI and DALI drivers.
•DMP – Phase control dimmer module for Leading or Trailing Edge output, suitable
for use with most types of dimmable electronic drivers.
•DMR – Relay control module for most types of switched loads.
The DMC2 can be surface or recess-mounted, and features a number of cabling knockouts
to accommodate a variety of communication, supply and load configurations.
January 15, 2019
DMC2 6 Product Overview
1.1 DMC2 Enclosure
The DMC2 enclosure is a galvanized steel case with powder coated front covers. It includes
mounting bays for power supply module, communication module and two output modules.
1.1.1 Dimensions
January 15, 2019
DMC2 7 Product Overview
1.1.2 Enclosure diagram
January 15, 2019
DMC2 8 Product Overview
1.2 DSM2-XX
The DSM2-XX fits into the top module bay of the enclosure, and supplies power to the
communication and control modules.
1.2.1 Dimensions / Diagrams
January 15, 2019
DMC2 9 Product Overview
1.3 DMD31X Module
The DMD31X module is a three-channel signal controller. Each channel is individually
configurable to DALI Broadcast, 1-10V or DSI.
1.3.1 Dimensions
January 15, 2019
DMC2 10 Product Overview
1.3.2 DMD31X module output wiring
The control signal must be terminated into the top six terminals on the module. The power
circuit must be terminated into the bottom six terminals as indicated in the diagram below.
Ensure that each signal and power channel has been paired and segregated correctly.
For installation involving 120 VAC circuits only:
Wire all output circuits using conductors suitable for Class 1 / Light and Power circuits rated
150 V minimum. The signal control circuit conductors can be intermingled with the branch
circuit wiring in the wire trough. The signal control circuit conductors can be considered as
Class 2 conductors. Class 2 wiring methods can be used for the signal control circuit outside
the DMC control panel.
For installation involving 240 or 277 VAC circuits:
Wire all output circuits using conductors suitable for Class 1 / Light and Power circuits rated
300V min. The signal control circuit conductors can be intermingled with the branch circuit
wiring in the wire trough. The signal control circuit conductors are to be considered as
Class 1 conductors. Class 1 / Light and Power wiring methods must be used for the signal
control circuit outside the DMC control panel.
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Controladores de Philips
Philips
Philips DYNALITE DDRC1220FR-GL Manual de usuario
Philips
Philips 9890 000 0268 Series Manual de usuario
Philips
Philips Dynalite DDBC1200 Manual de usuario
Philips
Philips iPlayer 3 Manual de usuario
Philips
Philips PTN3501 Manual de usuario
Philips
Philips dynalite LFC8400 Manual de usuario
Philips
Philips LLC7811/00 Manual de usuario
Philips
Philips Vaya Touch Controller Manual de usuario
Philips
Philips Lightolier Controls Sunrise Whispurr Manual de usuario
Philips
Philips 9290 014 61062 Manual de usuario
Philips
Philips LFH 2305 Manual de usuario
Philips
Philips SC1500 Manual de usuario
Philips
Philips LFC7310 Manual de usuario
Philips
Philips Dynalite DDBC516FR Manual de usuario
Philips
Philips Dynalite DDRC810DT-GL Manual de usuario
Philips
Philips ColorDial Pro Manual de usuario
Philips
Philips NOA0025 Manual de usuario
Philips
Philips Dynalite DLE1205 Manual de usuario
Philips
Philips iPlayer 3 Manual de usuario
Philips
Philips DYNALITE DDRC420FR Manual de usuario
