Philips VSS7901/00T Manual de usuario

Electro Magnetic Compatibility (EMC)

This equipment complies with European rules for EMC according to

EN55013, EN55020 and EN50082-1.

Operation is subject to the following two conditions:

1 This device may not cause harmful interference.

2 This device must accept any interference received, including interference

that may cause undesired operation.

The equipment conforms with the EMC directive and low-voltage

directive.

This device complies to FCC rules under test conditions that included

use of system cables and connectors between system components. If you

have any problems, contact your dealer.

Warnings

Any unauthorized modification to this equipment may cause violation of

the FCC rules resulting in the revocation of the authorization to operate

the equipment.

To prevent fire or shock hazard, do not expose this accessory to rain or

moisture.

The exclamation mark within a triangle is intended to alert the

user to the presence of important operating and maintenance

(servicing) instructions in the literature accompanying the

appliance.

Intercom Box

Table of contents

Page

Introduction .................................................................................................................4

Installation....................................................................................................................5

Mounting the box

System cable

Doorbell output

External power supply

Volume of the loudspeaker

Settings.............................................................................................................................9

Designating the box (CAMERA # switch)

Box number

Tamper switch active

Double addressing error

Operation...................................................................................................................11

English

Read these instructions, before putting your system in operation.

English

Introduction

Thank you for buying this accessory for your observation system.

1 System monitor

2 Video recorder (VCR)

3 Slave monitor

4 Accessory boxes (0-2 per cable)

5 Interface box

6 System cameras

7 Non system camera’s (CVBS)

8 Mains power adapter

The following items are included in this kit:

1 Intercom box

1 System cable (5m/15ft)

1 User manual

Colour Observation Monitor

CL 66610005_005a.AI

6 6 7

talk action menu _+next

auto view

Colour Observation system

Colour Observation Monitor

4 4

N.O. = Normally Open

N.C. = Normally Closed

The intercom box has a doorbell function. This means that a buzzer

inside the system monitor sounds when someone presses the intercom’s

doorbell button. When the doorbell button is pressed the monitor

switches to the camera input the intercom box is designated to. The

intercom box then allows you and the person near the intercom box to

talk to one another.

Installation

Remark: When the system configuration is altered, the system monitor needs to check

and memorise the configuration of the cameras and accessories connected to its inputs.

This is done automatically when the power is switched on. Use the power switch to

switch off, only operating the power save key is not sufficient. If switching off is

impracticable, use the auto install option of the system monitor’s install menu.

CL 66610005_511.AI

N.O.

N.C.

common

Mounting the box

1 Loosen the screw holding the cover and remove the cover.

2 Remove the circuit board 1.

3 Fasten the bottom plate of the box with two screws.

4 Fit the circuit board.

5 Now make the connections as described below.

6IMPORTANT: Adjust the settings of the circuit board switches to

configure the box according to your system. See section ‘settings‘.

7 Fit the cover and secure the screw holding it.

CL 66610005_509.AI

CL 66610005_502.AI

CL 66610005_504.AI

System cable

For the interconnections between the monitor, accessories and camera a

system cable is supplied. For an optimum picture and sound quality you

should always use 4-wire dual twisted-pair cable when extending the

connection (max. 300m/900ft). The cable and plugs are available in the

hobby and professional trade. Pay attention that the connectors are fixed

to the cable corresponding to the figure below.

If the cable length between monitor and camera exeeds 200m/600ft after

an accessory is inserted in the line a mains power adapter should be used

to power the camera (see accessories).

Caution: The plugs used for the observation system have the same dimensions as

standard telephone plugs.

Never connect the security system with telephone equipment!

The two sockets for the system cable are interchangeable. One socket

connects the box to the system component previous in the cable, the

other to the next (if any).

CL 66610005_006.AI

4-5

2-3

4-5

2-3

Doorbell output

The figure below shows the screw terminals to which a separate bell can

be connected.

1 System-cable input

2 System-cable output

3 Switches 1, 2 & 3

4 Rotary switch (designates the box to a camera input)

5 Tamper switch

6 Volume preset

External power supply

If at maximum volume setting the loudspeaker volume remains low, then

connect an external power supply (24VDC, 0,5A), as shown in the figure

above (7). This is advised when the intercom box is connected to the

system monitor through a long cable.

CL 66610005_508.AI

689

+24VDC

CAMERA #



123

1 BOX

BELL

+24V

GND

TAMPER

N LAST

ON OFF

Volume of the loudspeaker

Adjust the volume of the sound reproduced at the intercom box with the

volume preset (6).

Settings

Four switches - located inside the case, on the circuit board - are used to

configure the circuit according to the system.

•The rotary switch designates the box to a particular camera input.

•The three small slide switches have the following functions:

Switch Off On Description

1 BOX 1 2 box number

2 TAMPER OFF ON tamper-switch override

3 LAST N Y last accessory box

Designating the box (CAMERA # switch)

Designating a box to a camera input means that system monitor

associates the box with a certain camera input (the designated input)

although it is physically connected to another. This causes the system

monitor to switch to the camera connected to that input when for

example an alarm is triggered or the doorbell button pressed. This gives

you the opportunity to use the shortest route when wiring a box. The

figure below shows for example a two camera system with three accessory

boxes. The switch CAMERA # is set according to the camera (input) to

which the boxes are designated.

Note: Switch positions 0 and those beyond the maximum number of inputs have no

function.

Box number

This switch (BOX) informs the circuit about the accessory number when

two boxes are designated to the same camera input of the system

monitor. A maximum of two intercom boxes can be designated to one

camera input.

Switch 1 (BOX)

Position Description

1 first box which is designated to the camera input set

by CAMERA #

2 second box which is designated to the camera input

set by CAMERA #

Tamper switch active

On the circuit board a tamper switch secures the box. When opening the

box this switch triggers an alarm on the monitor. To suppress a

continuous alarm message while servicing the system, the tamper-switch

override is set in the TAMPER OFF position.

Caution: Don’tforgettoreactivate thetamperswitchbyswitchingtheoverrideto

the TAMPER ON position!

Double addressing error

CL 66610005_510a.AI

689

CAMERA #

689

CAMERA #

talk action

menu _+next

auto view

Colour Observation system

Two alarm/action boxes or intercom boxes, which are designated to the

same camera input, have the same ‘box-number’.

If the system monitor detects two boxes with the same designation and

box number, it shows the following error message:

DOUBLE ADDRESSING

“Accessory name”

INPUT X/X

Change from one intercom box the BOX switch or the CAMERA #

switch.

Explanation:

Operation

The button on the intercom is used as (door)bell. When pushed, the

buzzer in the monitor (system & slave) sounds. The monitor (system &

slave) switches to the camera input the intercom is designated to. The

automatic camera sequence stops. If you don’t react within 3 minutes - by

pushing any button - then the monitor returns to its previous status (for

example, the automatic camera sequence continues).

The system monitor reproduces the sound received from the intercom

box (plus that of the camera the system switched to, if its microphone is

not switched off). To talk back to your visitor push H. The sound

received by the system monitor’s microphone is then reproduced by the

intercom.

INPUT X/X

the physical camera input numbers to

which the double addressed boxes are

connected.

Tabla de contenidos

Otros manuales de Accesorios de Philips

Philips

Philips LRI8135/00 Manual de usuario

Philips

Philips CRP385 Manual de usuario

Philips

Philips INFRACARE HP3643 Manual de usuario

Philips

Philips ActiLume Classic Guía de instalación

Philips

Philips HF3470 Manual de usuario

Philips

Philips Dynalite DUS360CR Manual de usuario

Philips

Philips HF3506/06 Manual técnico

Philips

Philips CRP343 Manual de usuario

Philips

Philips HF3500 Manual de usuario

Philips

Philips SDW5061GN Manual de usuario

Philips

Philips T5VHO Guía

Philips

Philips 14792-6 Manual de usuario

Philips

Philips CRP139 Manual de usuario

Philips

Philips CRP383 Manual de usuario

Philips

Philips LP2PB201CS Manual de usuario

Philips

Philips HF3507 Manual de usuario

Philips

Philips HP 3610 Manual de usuario

Philips

Philips DLA81818H Manual de usuario

Philips

Philips CRP140 Manual de usuario

Philips

Philips CRP345 Manual de usuario

Philips

Philips DLA7575H Manual de usuario

Philips

Philips P-5899-A Manual de usuario

Philips

Philips sonicare AirFloss Ultra Manual de usuario

Philips

Philips SAC2550W/10 Manual de usuario

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario