Perry Electric TE542 Manual de usuario

models:

TE543

RECESSED DIGITAL THERMOSTAT H 45 mm

TE542

LUMINOUS TOUCH SCREEN DISPLAY

2x 1.5dc

Battery powered

230V ac power supply

Winter / Summer operation 2

temperature levels + antifreeze

AA -LR6

Instructions for installation and use

PE - DETIPE022 10/18

Input for telephone programmer

T Set

Mode

ON OK

Mode

T Set

Machine Translated by Google

p. 3 6 - RESET OPERATION

5 - PROGRAMMABLE FUNCTIONS

4 - INSTRUCTIONS FOR USE

WARNINGS!

3 - INSTALLATION

IMPORTANT: for the procedure for assembling the thermostat with the plate of the civil series chosen, follow

the instructions given in the specific compatibility sheet contained in the package.

2 - KEY TO DISPLAY AND KEY FUNCTION

COMPATIBILITY WITH PLATES OF THE MOST COMMON CIVIL SERIES

1 - TECHNICAL DATA

p. 4

p. 5

p. 9

INDEX

p. 13

p. 18

p. 19

7 - POSSIBLE PROBLEMS AND SOLUTIONS

Machine Translated by Google

Autonomy from power on on the display of the

flashing low battery symbol:

Battery model autonomy:

about 1 month

timed to 5 sec. from the last pressure on the touch screen (battery

model) timed to 5 sec. from the last press on the touch screen or fixed (230V ~

model) class A 4 kV 1 / B / Electronic relay with NO / COM / NC potential free

changeover contact max 5 (3) A / 250V ~ 2 conductors (only 230V ~ power

supply model) 2 or 3 conductors for potential-free NO contact 1.5 mm ÷ 2.5 mm

COMFORT / REDUCTION (saving) / ANTIFREEZE (OFF) 0 ÷ + 37.7 ° C 0.1 ° C

TECHNICAL DATA

Output Type:

Alkaline

type AA (LR6)

model at mains voltage 230V ~ 50 ÷ 60Hz about 2 years

Type of action, disconnection and device:

battery-powered model 2 x 1,5V stylus batteries

Rated impulse voltage:

ErP Class I; 1% (Reg. EU 811/2013) 1

° K / 15 min IP 30 II normal 0 ° C ÷ +

45 ° C -10 ° C ÷ + 60 ° C LVD - EMC

EN60730-1 EN60730-2-9

Supply voltage:

Software:

settable from 0.2 ° C to 1.2 ° C (default 0.5 ° C)

settable from 7 to 20 minutes (default 10 minutes)

1 - TECHNICAL DATA

Display backlight:

+ 5 ° C ÷ + 37.0 ° C (limitable)

0.1 ° C ± 0.5 ° C adjustable -2

° C ÷ + 2 ° C (default 0.0 ° C)

+ 4 ° C ÷ + 12 ° C (adjustable or excludable

set) (default 4 ° C)

TECHNICAL DATA

Mains power connection: User

connection (load): Input for connection

to program. Telephone: Cable section at the terminals:

Settable temperature levels: Room temperature display

range: Room temperature resolution: Adjustment range

T COMFORT and REDUCTION temperature set: Set

temperature resolution: Tolerance on temperature

reading: Room temperature reading correction (Offset ):

Antifreeze temperature: Type of temperature regulation:

- ON / OFF with thermal differential - Modulating

proportional with ErP control period Energy

classification: Thermal gradient: Degree of protection:

Insulation class: Pollution degree: Operating

temperature limits: Operating temperature limits

storage: Reference standards for CE markings:

Machine Translated by Google

C.marker UP key ( )

allows you to increase the value of a setting D. marker

DOWN key ( ) allows you to decrease the value of a setting E. marker OK

key:

2 - DISPLAY LEGEND AND KEY FUNCTIONS (touch screen)

45. Night setback (saving) mode

And

Mode

pulse pressure for "User" settings: - operating

mode with COMFORT temperature: WINTER (heating) or SUMMER (cooling) - operating mode with NIGHT

REDUCTION temperature in Winter or Summer - thermostat mode in OFF

2via telephone programmer (optional)

1. Set temperature set:

COMFORT or REDUCTION or

ANTIFREEZE 2. Mode in (cooling)

SUMMER 3. Activation of

the user connected to the thermostat

The touch screen has 4 touch sensitive areas (markers). At the first touch on any point of the touch screen, the keys on the

display light up after which within 5 sec. press the key or relative area to change the settings (note: each time a key or relative

area is touched, a 5 sec time-out is reactivated).

TOUCH SCREEN:

56. WINTER

(heating) mode 7. Room

temperature display 8. Backlit display: in

timed mode (factory setting) the first time

you touch any point of the touchscreen, the display lights

up and shows the keys for 5 sec. - in fixed

mode (only for 230V~ model) the display is

always lit, the keys are displayed for 5 seconds

when you first touch any point on the touch

screen.

Note: further particular functions of

the keys or related areas are

described in the specific use paragraphs.

long press (4 sec.) for “Installer” settings: accesses the PROGRAMMABLE FUNCTIONS menu

34. Signal connected to the ON function (with

flashing symbol)

T Set

B. markers Mode key.

A. sensitive areas

9. Low battery warning (3V dc model only)

- short press: operation confirmation -

long press (4 sec.): exits the PROGRAMMABLE FUNCTIONS menu

Machine Translated by Google

43.5 4743.5

Thermostat installation: independent - fixed

recessed in 3-module rectangular box. install the

thermostat at about 1.5 ÷ 1.6 m from the ground away from heat

sources, windows and anything else that could affect its normal

operating status.

A) Wall mounted

boiler B) Burner or Circulation pump or

Motorized solenoid valve C) Zone

solenoid valve NB: the examples shown

in this documentation are basic.

Heating systems with thermostat that

controls:

Important: the installation and electrical connection of the devices

and equipment must be carried out by qualified personnel and in

compliance with the standards and laws in force. The manufacturer

assumes no responsibility for the use of products that must follow

particular environmental and / or installation standards, the burden

of which remains the responsibility and the responsibility of the installer.

battery-

powered thermostat module

3.2 - RULES FOR INSTALLATION

3.3 - INSTALLATION EXAMPLES Attention:

before installing, switch off the mains voltage

AB BB

3.1 - OVERALL DIMENSIONS

3 - INSTALLATION

20 14

h 1.5 m

IMPORTANT: for the installation procedure

of the thermostat with the plate of the civil

series chosen, follow the instructions

given in the specific compatibility sheet

contained in the package.

Machine Translated by Google

3.4.1 - ELECTRICAL CONNECTIONS

3 - INSTALLATION

template:

Connection to a motorized valve and to

a telephone programmer

TE542

No.

Telephone programmer contact

for thermostat control

6 7

closes

LN extension

Examples of electrical connections:

TE542

230V~

opens

ONLY MODEL TE542 BATTERY POWERED (3Vdc)

LOAD

6 7

Telephone programmer contact

for thermostat control

template:

Connection to a boiler and a

telephone programmer

ATTENTION! only

for TE542 model powered by 3V dc batteries

WATER HEATER

230V ~

NB: with strong inductive loads (pumps

and solenoid valves) it is recommended

to connect an RC filter in parallel to the

load.

Machine Translated by Google

3.4.2 - ELECTRICAL CONNECTIONS ATTENTION! only for

model TE543 mains power supply 230V~

template:

NB: with strong inductive loads (pumps

and solenoid valves) it is recommended

to connect an RC filter in parallel to the

load.

3 - INSTALLATION

Programmer

opens

LOAD

230V~

1 2

No.

contact for

thermostat control

switch off the 230V ~ mains voltage

230V ~

TE543

230V~

Programmer

Examples of electrical connections:

TE543

Telephone

ONLY MODEL TE543 230V~ POWER SUPPLY

230V ~

closes

No.

Connection to a boiler and a

telephone programmer

template:

Telephone

WATER HEATER

No.

Connection to a motorized valve and a

telephone programmer contact for

thermostat control

230V ~

Machine Translated by Google

ALKALINE

Warning: the battery life can be over 2 years.

Dispose of exhausted

batteries by throwing

them in the appropriate

containers and in any

case in accordance

with the provisions of

the environmental

protection regulations.

1st However, it is advisable to replace them at least every 24 months to prevent

them from running out during periods of absence (e.g. Christmas holidays, etc.)

(Duracell or Energizer batteries recommended)

All programming operations can be carried

out before inserting the thermostat module

into the wall recessed base; this allows

programming while comfortably seated.

Insert or replace with 2 x 1,5V AA-LR6 batteries

paying attention to polarity USE GOOD

QUALITY ALKALINE BATTERIES

3.5 - REMOVING AND INSERTING THE THERMOSTAT (e.g. replacing batteries, programming)

NEVER carry out the same operation with the TE543

model with a 230V~ power supply, the module is fixed!.

If the thermostat module is programmed before it is inserted

into the recessed base, when installation is complete, the ON

indication (off or flashing) on the display may not correspond to

the real state of the relay. Within max 1 minute of

inserting the thermostat module into the

recessed base, the relay will activate according to the ON

indication (off or flashing) on the display.

ONLY MODEL TE542 BATTERY POWER SUPPLY (3Vdc)

ATTENTION!

Reinsert the thermostat

module fully into the

recessed base.

3 - INSTALLATION

Extract the thermostat

module by grasping it

with your fingers in the

appropriate seats.

3rd

2nd

Programming convenience (only

for battery-powered model)

Attention!

Machine Translated by Google

Mode

note: to switch from one operating mode to another, follow

T Set

IMPORTANT!

Winter night reduction = heating

Press the

Mode key twice

OFF

Mode

4.2 - OPERATING MODE CHANGE

with COMFORT temperature

SUMMER = cooling

The figures below show the transition from COMFORT temperature to REDUCTION temperature in WINTER mode

within 5 sec.

The thermostat has 5 operating modes:

the written

Mode to return to the mode

Press the OK key

Press the

Mode button once

Press

the button 3 times

T Set

antifreeze temperature (if not excluded during programming)

Change from

Mode

or the related area as per the following procedure:

WINTER = heating (factory setting)

completely deactivated

previous operation.

4.1 - OPERATING MODES

Change from NORMAL OPERATION to OFF

5 seconds to confirm.

Press the

key once

touch screen (to display the keys)

REDUCTION and vice versa

press the OK button within 5 seconds to confirm.

Change from WINTER to SUMMER and vice versa

T Set

5 seconds to confirm.

touch screen the keys light up, press the keys within 5 sec

In heating mode: the mode is active

with REDUCTION temperature (saving)

Mode

important: always press inside the 4 sensitive areas (the gray vertical lines indicate the separation between one area and the other and are not sensitive to touch)

Operating mode

- In cooling mode: the system is

the indications in the following paragraph.

4 - INSTRUCTIONS FOR USE

with REDUCTION temperature (saving)

the relative symbols and the

set temperature flash; press the OK key within

(and the antifreeze

temperature set only in the "Winter" function) flash;

a NORMAL OPERATION

Press anywhere on the display

Change from COMFORT temperature to

the relative symbols and the set

temperature flash; press the OK button within

with COMFORT temperature

example: heating operation active

press the Mode button once

At the first touch on any point (marker) of the display

Thermostat off

Summer night reduction = cooling

within 5 sec.

to confirm.

Display

symbols

Machine Translated by Google

Boiler in operation with ambient temperature below 20.0 ° C

thermostat resumes previous operation.

5 - INSTRUCTIONS FOR USE

equal to winter “Reduction” temperature.

Note: it will be possible to lock the maximum temperature sets and

Air conditioner in operation with ambient temperature above 25.0 ° C

- Boiler in operation with ambient temperature below 4.0 ° C

t acting directly The thermostat allows T Set settings from +5 ° C to 37.0 ° C

desired operating mode.

Summer night reduction:

From current mode

“Reduction” temperature 17.5 ° C

Set set.

Passed

PROGRAMMABLE FUNCTIONS) the user will not be able to set the Set

it is immediately stored.

Or:

Comfort temperature 20.0 ° C

seconds from the last time a key was pressed

Winter: higher “Comfort” temperature setting o

Each pressure of the keys involves the variation of 0.1 degrees; by

keeping pressed you obtain the fast scrolling of the values.

“Comfort” temperature 25.0 ° C

from winter mode Antifreeze temperature 4.0 ° C (adjustable or excludable)

temperature T Se ON

until the

Mode

Air conditioner in operation with ambient temperature above 28.0 ° C

4.3 - MODIFY SET TEMPERATURE T Set

equal to the summer "Reduction" temperature.

Winter night reduction:

press the keys

to change the T value

Note: if the antifreeze temperature has been excluded (see chap.

new setting

Winter mode (heating):

3rd

conditions:

setting the

Summer mode (cooling):

Thermostat off

IMPORTANT!

times the Mode key

“Reduction” temperature 28.0 ° C

4 - INSTRUCTIONS FOR USE

Summer: lower “Comfort” temperature setting o

T Set

minimum (see chap. PROGRAMMABLE FUNCTIONS).

within 5 seconds:

- Air conditioner always deactivated

on the keys: la with temperature values that satisfy the following

example:

1st

2nd

you can edit

Mode

Boiler in operation with room temperature below 17.5 °C

antifreeze temperature.

T Set

Press one or more

Machine Translated by Google

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Termostato de Perry Electric

Perry Electric

Perry Electric V002 Series Guía

Perry Electric

Perry Electric TE541 Manual de usuario

Perry Electric

Perry Electric 1TX CR028WIFI Guía

Perry Electric

Perry Electric MODULE Series Manual de usuario

Perry Electric

Perry Electric Recess Series Manual de usuario

Perry Electric

Perry Electric TE540 Manual de usuario

Perry Electric

Perry Electric RECESS Series Manual de usuario

Manuales populares de Termostato de otras marcas

EWELLY

EWELLY EW-181 Manual de usuario

Prolon

Prolon T1100 Instrucciones de instalación

Computherm

Computherm Q20 Manual de usuario

Heatmiser

Heatmiser neoStat Manual de usuario

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manual de usuario

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manual de usuario

Saswell

Saswell SAS920XWHB-7-S-RF Guía

Aircalo

Aircalo TFP1-ET85P2 Manual de usuario

Honeywell

Honeywell CM721 Manual de usuario

Carrier

Carrier DEBONAIR 33CS Manual de usuario

Lennox

Lennox iHarmony Zone Thermostat Instrucciones de montaje

Gemtech

Gemtech GT7000 Manual de instrucciones

Rollei

Rollei Smartes 45000 Manual de usuario

Sinope

Sinope TH1300RF Manual de usuario

Honeywell

Honeywell RLV4305 Manual de usuario

Honeywell

Honeywell Prestige 2.0 THX9421 Manual de usuario

NuTone

NuTone NTBZ48 Instrucciones de funcionamiento originales

Stelpro

Stelpro MAESTRO ASMT402AD Manual de usuario