PerkinElmer Lambda 465 Manual de usuario

09931238D

Lambda 465 Peltier Control Single Cell with Peltier

Controller Installation Instructions

This instruction sheet describes the installation of this accessory which is used with the Lambda 465

Spectrophotometer.

NOTE: Read these instructions before you install this accessory.

Contacting PerkinElmer

Supplies, replacement parts, and accessories can be ordered directly from PerkinElmer, using the part

numbers.

See our website:

http://perkinelmer.com

PerkinElmer's catalog service offers a full selection of high-quality supplies.

To place an order for supplies and many replacement parts, request a free catalog, or ask for information:

If you are located within the U.S., call toll free 1-800-762-4000, 8 a.m. to 8 p.m. EST. Your order will be

shipped promptly, usually within 24 hours.

If you are located outside of the U.S., call your local PerkinElmer sales or service office.

Features

•Easy to install

•Full software control

•Liquid cooling system

•N2gas purging available

Figure 1. Lambda 465 Peltier control Single Cell [P/N: N4104009]

09931238D

Dimensions and Specifications

Dimensions of Peltier Controller

Physical Characteristic Specification

Power

100-240 VAC, 50/60 Hz, 300W, Free Voltage

Temperature Range

-10 to 100°C (Maximum Internal Temperature)

Maximum Ambient Operating Temperature

40°C

Dimensions

310 (W) x 410 (D) x 275 (H)

Weight

20.0 kg

Coolant Volume

2 L

2Gas Available 100 psi (6.9 bar)

Liquid Cooling

System

Magnetic Stirrer Control Available

Emergency Power Off Switch Available

Dimensions of Peltier Control Single Cell

Physical Characteristic Specification

Dimensions 101(W) x 189(D) x 133(H) mm

Weight 2.2 kg

Temperature Accuracy ±0.15°C

Temperature Precision ±0.1°C

Temperature Stability ±0.1°C

Ramping Time (from 0 to 100°C) 4 minutes

09931238D

Safety Warnings

WARNING

When this label is attached to an instrument it means refer to the

manual.

Lorsque cette étiquette est attachée à un instrument, il est nécessaire

de voir le manuel.

See the following figure for the location of warning labels on the back of the instrument:

Warning

To prevent electrical shock,

do not open cover.

Refer all servicing to qualified

personnel.

Avertissement

Afin d’éviter tout risque

d’électrocution ne pas enlever

Warning

For continued protection against electrical

shock, replace with same type and ratings of

fuse

Avertissement

Pour assurer la protection contre le risque de

choc électrique, remplacez le fusible

seulement avec le même type et la même

valeur nominale.

Warning

FUSE

Avertissement

FUSE

09931238D

Description

Configuration of the Peltier Control Single Cell Holder

Figure 2 Lambda 465 Peltier Control Single Cell

a) Interface connector between Peltier Single Cell Holder and Peltier Controller

b) Coolant Inlet/Outlet Quick Coupler

c) N2 gas fitting

d) Interface slot for Temperature Probe

e) Cell Lifting knob

f) Temperature probe

Figure 3 Temperature Probe Accessory

Figure 4 Base Plate

09931238D

Figure 5 Wrench bolt M5, Length 15 mm, 2 ea

Figure 6 Phillips round head screw with washer M4, 15 mm, 4 ea

Front View of Peltier Controller

Figure 7 Front view of the Peltier Controller

a. Manual touch pad with Display: Temperature Control Unit (Heating/Cooling Block)

b. LED Indicators: Indicate the status of the operation of Coolant circulation, Fan, Pump, etc. (If

there is a problem in the components, Red LED will flash with beep alarm.).

c. Manual ON/OFF button: As the Manual ON/OFF button is ON, the temperature can be

controlled manually by a) Manual touch pad with display.

NOTE:

Manual operation is used only for the manufacturing process so it should be turned off during the

measurement.

d. N2gas ON/OFF button:It is used for using N2gas to remove the frost from the heating and

cooling.

e. Stirrer ON/OFF button: It is used for controlling of the stirring.

f. Stirrer Speed Controlling Knob: Control the stirring speed (rpm).

g. Emergency switch: Stop all the operations in an emergency situation.

NOTE:

During the operation, the emergency switch should be turned off.

h. Coolant Inlet

09931238D

Rear View of Peltier Controller

Figure 8 Rear view of the Peltier Controller

a. RS-232 port

b. AC POWER:Main Power ON/OFF

c. FUSE:AC Socket + Fuse Holder

d. INTERFACE:Interface cable for connecting with Peltier control Single Cell

e. Air Vent Manual switch:Used for removing the air in the coolant hose.

f. Buzzer: It makes an alarm sound. If there is any problem before the measurement, the buzzer

beeps 6 times every 10 sec. If the malfunction occurs during the operation, the buzzer beeps

twice every 10 sec.

g. Quick Coupler of Coolant lnlet/Outlet

h. Quick Coupler of Coolant Drain

i. N2Gas Inlet/Outlet ports

NOTE:

N2gas is not always required [Tube for N2 gas is not supplied with the accessory].

j. Flow Gauge: Indicator of the flow rate of N2gas.

09931238D

Configuration of the equipment

Peltier control Single Cell

Peltier Controller

Power Cord, 3ea

Base Plate, 1ea

Wrench bolt. 2ea

Phillips round head screw with washer, 4ea

Coolant Hose, 1ea

Magnetic Stirrer, 1ea

Coolant, 2ea

Waste Basket for Coolant, 1ea

Waste Hose for Coolant, 1ea

Interface Cable (RS-232 or USB to RS-232), 1 each

Spare Fuse (AC 250V T5AL), 2ea

Temperature Probe, 1ea

Installation

1. Place the Lambda 465, Peltier Controller and Peltier Control Single Cell in a location that is

compatible with the required environmental conditions for the operation.

2. Open the lid of the coolant inlet on top of the Peltier Controller.

Figure 9 Lid of coolant inlet

3. Fill up the liquid coolant using the funnel.

CAUTION

ATTENTION

Make sure the instrument is turned off while installing this accessory.

Assurez-vous que l’instrument est é

teint lors de l’installation de cet

accessoire.

09931238D

NOTE

Keep the amount of liquid coolant to the level where the indicator is located between the ‘L’ (low) and ‘H’

(high) mark in the scale on the left side of the Peltier Controller. When the coolant is running short for the

operation, the LED of Low Water Level changes to red with an alarm sounding.

CAUTION

ATTENTION

The liquid coolant must

be used as refrigerant.

Do not use any water (tab

water, DI, etc).

In case that the water is used as refrigerant, Peltier Controller’s

components might be corroded and its performance may be deteriorated.

Use any kind of liquid coolant in normal grade as is available (e.g. liquid coolant

including Distilled Water 70 wt%, Propylene Glycol 27 wt%, Additives 3 wt%).

Le liquide de refroidissement doit être utilisé comme réfrigérant.

N'utilisez

jamais d'eau (eau du robinet, eau déminéralisée, etc.)

L'eau risque en

effet de corroder les composants du contrôleur Peltier et de réduire les

performances de ce dernier.

Utilisez un liquide de refroidissement du commerce de qualité normale (par

exemple, un liquide de refroidissement à base d'eau distillée à 70 % M/V, de

propylène glycol à 27 % M/V et d'additifs à 3 % M/V).

4. Connect the power cord and the communication cable of the Lambda 465.

NOTE:

Make sure that the instrument is turned off when the accessory is installed.

5. Take apart the existing cell holder in the sample compartment.

Figure 10 Taking apart the existing cell holder

09931238D

6. Place the base plate at the bottom of the sample compartment and tighten the bolt with a

wrench. Next fix and tighten the Peltier Control Single Cell with the Phillips round screw.

Figure 11 Placing the plate at the bottom of the sample compartment

7. Connect the accessory interface cable of the Peltier Controller to the interface connector of the

Peltier Control Single Cell.

Figure 12 Connecting the accessory interface cable of the Peltier Controller to the

interface connector

09931238D

8. Connect the coolant inlet/outlet and N2gas tube between the Peltier Controller and the Peltier

Control Single Cell.

NOTE:

N2 gas is not always required, so the gas and inlet hose are not supplied.

Figure 13 Connecting the coolant inlet/outlet and N2gas tube

9. Connect the temperature probe to the interface slot of the Peltier Control Single Cell.

Figure 14 Connecting the temperature probe

10. Connect the Peltier Controller with the PC via the RS-232 or USB to RS-232 cable. See Installing

the USB to RS-232 driver on page 15 when you use the USB to RS-232 cable.

Figure 15 Connecting the Peltier Controller

Otros manuales para Lambda 465

Tabla de contenidos

Otros manuales de Equipo de laboratorio de PerkinElmer

PerkinElmer

PerkinElmer TriNEST Manual de usuario

PerkinElmer

PerkinElmer Frontier Optica FT-IR Manual de usuario

PerkinElmer

PerkinElmer clarus 500 gc Manual de usuario

PerkinElmer

PerkinElmer Raman IdentiCheck Manual de usuario

PerkinElmer

PerkinElmer Lambda 650 Instrucciones de instalación

PerkinElmer

PerkinElmer Lambda 650 Instrucciones de instalación

PerkinElmer

PerkinElmer FL 6500 Manual de usuario

PerkinElmer

PerkinElmer OPTIMA 8000 Manual de usuario

PerkinElmer

PerkinElmer UATR Manual de usuario

PerkinElmer

PerkinElmer Lambda 25 Manual de usuario

PerkinElmer

PerkinElmer VICTOR Nivo Manual de usuario

PerkinElmer

PerkinElmer OilExpress 4 Manual de usuario

PerkinElmer

PerkinElmer AVIO 200 Instrucciones de instalación

PerkinElmer

PerkinElmer CLARUS 680 GC Manual de usuario

PerkinElmer

PerkinElmer FL 6500 Manual de usuario

PerkinElmer

PerkinElmer IVIS Lumina XRMS III Series Manual de usuario

PerkinElmer

PerkinElmer Caliper IVIS Spectrum Manual de usuario

PerkinElmer

PerkinElmer IVIS Lumina S5 Manual de usuario

PerkinElmer

PerkinElmer Clarus 600/560 D MS Instrucciones de instalación

PerkinElmer

PerkinElmer LED Solutions ACULED Designer Kit Silver Manual de usuario

PerkinElmer

PerkinElmer HATR Manual de usuario

PerkinElmer

PerkinElmer Frontier FT-IR Manual de usuario

PerkinElmer

PerkinElmer Clarus SQ 8 MS Series Instrucciones de instalación

PerkinElmer

PerkinElmer LAMBDA 265 Manual de usuario

Manuales populares de Equipo de laboratorio de otras marcas

Qiagen

Qiagen DML 3000 Manual de usuario

Queensgate

Queensgate NANOSCAN OP400 Manual de programación

Conviron

Conviron GEN1000-GE Manual de usuario

Parr Instrument

Parr Instrument 4560 Manual de instrucciones

IKA

IKA IC control Manual de usuario

Integra

Integra DOSE IT Manual de usuario

Agilent Technologies

Agilent Technologies 5800 ICP-OES Manual de usuario

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Manual de usuario

NI PXI-5422 Manual

Collomix

Collomix Aqix Manual de usuario

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Manual de usuario

Ocean Insight

Ocean Insight FLAME-NIR+ Manual de usuario

Parker

Parker ALIGN-MG-NA Manual de usuario

BD 644787 Manual de usuario

DENTAURUM

DENTAURUM Compact Megaplus Manual de usuario

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Manual de usuario

VWR

VWR SAS Super IAQ Manual de usuario

illumina

illumina MiSeqDx Manual de usuario