Percussion Play PPBDL-S Manual de usuario

Install

Instrument

with 1.5m free

space (from

widest point)

around it.

1.5m

Surface Fixed

Babel Drum

Page 1 of 2

1. Unpack ground fixing legs

3no.

Installation Instructions

Played with hands

22 Kg

13.4 Kg

Ground Fix

Components:

Weight of heaviest part 17.5kg (Large Babel Drum)

Weight of heaviest part 13.4kg (Small Babel Drum)

BS EN 1176

Metric Conversion:

850mm/ 33 15/32”

855mm/ 33 21/32”

1.5m/ 59”

CAUTION: Drum

surface can get hot

in direct sunlight, if

possible install in

shaded areas.

2. Lay packaging out on floor

or assemble on non-abrasive

surface to prevent marking of

polished stainless steel.

3. Align holes on legs to holes

on surface fixing(opposite

end to polished domes) and

secure in place using 3no.

M10 x 30mm Screws

provided

Tools required TX 45 Driver

Bit)

4. Invert assembled frame so

domed ends face upwards.

5. Place 8mm Hex Key

supplied into hole in leg and

lock into internal bolt.

6. Remove Black Cap

opposite side of leg and

keeping Hex Key in place,

slide black polyurethane

damper over bolt until flush

with end of bolt. Repeat for

other 2 legs

8. Align holes in side of babel

drum with bolts on legs.

9. Using 8mm Hex Key screw

bolts into drum to secure in

place.

Use thread locking solution

All hole locations are laser cut

for accuracy to ensure holes

in drum align perfectly with

legs.

7. Unpack babel drum leaving

black film in place to protect.

10. Using TX40 driver

provided secure M8 x 25mm

security bolts into external

holes in legs 3no. Use thread

lock solution

Instrument

Components:

M8x25mm Pin Torx

Ground Surface

850mm from Plate

Large 8 note Small 6 note

11.Locate Babel Drum in

desired location and mark

holes to fix to desired surface.

12. Fix to Surface using

recommended ground

anchors (Ground Anchors are

not supplied)

13. Make sure all fixings are

covered and secure using

cover caps provided

M10x30 Security Screw

2 Part Cover Cap

x4 Ground Anchors

not supplied

Spares available from

percussionplay.com or from your

local distributor

855mm from Plate

Locate the Surface fix

Plate into the leg of the

instrument.

Fix instrument to Surface

fix plate using M10

Screws and use thread

locking solution to

prevent fixings working

loose.

Fix Surface Plate to the

ground surface Ground

Anchors Not provided

cover fixings with caps

provided

Surface Fixed

Babel Drum

Page 2 of 2

Assembly Guide PPBDL-S

Played with hands

Instrument

Components:

Ground Fix

Components:

22 Kg

13.4 Kg

BS EN 1176

M8x25mm Pin Torx

1 2 3

Thread Lock Solution

Required

Thread Lock Solution

Required

Hex T Key

TX 40 Driver Bit

Tools:

M10x30 Security Screw

2 Part Cover Cap

x4 Ground Anchors

not supplied

TX 45 Driver Bit

Spares available from

percussionplay.com or from your

local distributor

Surface Fixed

Instrument

Components:

M6x20 Security Screw

1525mm

M6 Saddle Strap

Ground Surface

Installation Instructions

M10 Barrel Nut

M10x70 Security Screw

Ground Fix

Components: 23.5 Kg

Install Instrument

with 1m free space

(from widest point)

around it.

1.5m

Pair Small Red

Beaters X1

1.5m

Bell Lyre

Page 1 of 2

Weight of heaviest part 14.4kg (Bell Lyre)

BS EN 1176

Metric Conversion:

1.5m/ 59”

1525mm/ 60” CAUTION: Bell

Lyre surface can

get hot in direct

sunlight, if possible

install in shaded

areas.

2 Part Cover Cap

1. Attach Surface Fixing posts

to legs(See Surface Fix Post

Installation Sheet)

3. Fix Surface Plate to level

surface using Coachscrews,

Rawlbolts, chemical anchors

or similar as deemed

appropriate by Installer.

(It is your responsibility to

ensure that the existing

surface is suitable to

receive the appropriate

fixing)

2.Locate Plate in desired

location and mark holes to fix

to desired surface.

4. Make sure all fixings are

covered and secure using

cover caps provided

Ground Anchors

not supplied

Spares available from

percussionplay.com or from your

local distributor

Locate the Surface fix

Plate into the leg of the

instrument.

Fix instrument to Surface

fix plate using M10 bolt

and Barrel Nut and use

thread locking solution

to prevent fixings working

loose.

Fix Surface Plate to the

ground surface Ground

Anchors Not provided

cover fixings with caps

provided

Surface Fixed

Components:

Surface Fix Post Installation

(1.1)

12 3

Bell Lyre

Page 2 of 2

M10 Barrel Nut

M10x70 Security Screw

TX 45 Driver Bit

Tools:

BS EN 1176

Thread Lock Solution

Required (Not Supplied)

Thread Lock Solution

Required (Not Supplied)

2 Part Cover Cap

Surface Fixed

Handpipes

Page 1 of 3

Ground Surface

905m

Installation Instructions

(1.1)

Instrument

Components:

25 Kg

2. Attach Surface Fixing posts

to legs (See Surface Fix Post

Installation Sheet)

1. Handpipes will arrive on

site assembled, Surface

Fixings will need to be

installed (1.1) (See Assembly

Guide)

Install Instrument

with 1.5m free space

(from widest point)

around it.

1.5m

Weight of heaviest part 20kg (Handpipes)

BS EN 1176

Metric

Conversion:

250mm/ 10”

400mm/ 16”

905mm/ 35”

1.5m/ 59”

Played with hands

Instrument assembled

Surface Fix

Components: M10 Barrel Nut

M10x50 Security Screw

x2 Ground Anchors

not supplied

2 Part Cover Cap

4. Fix to Surface using

recommended ground

anchors not supplied

3.Locate Instrument in

desired location and mark

holes to fix to desired surface.

5. Make sure all fixings are

covered and secure using

cover caps provided

Spares available from

percussionplay.com or from your

local distributor

COMPONE NTS LIST:

M10 x60mm Security Screw X2

M10 Barrel Nu t X2

M10 Nut X8

M1 0 x2 0 0 Th readed Bar X4

M10 x60mm Security Screw X2

M10 Barrel Nu t X2

Surface Fixed

Assembly Guide PPHAND

(1.1)

Surface Fix

Components: 25 Kg

Handpipes

Page 2 of 3

BS EN 1176

Thread Lock Solution

Required (Not Supplied)

Played with hands

Instrument

Components:

Instrument assembled

M10 Barrel Nut

M10x50 Security Screw

x2 Ground Anchors

not supplied

2 Part Cover Cap

498

Spares available from

percussionplay.com or from your

local distributor

M10x50 Security Screw X2

Surface Fixed

Components:

Surface Fix Post Installation

Handpipes

Page 3 of 3

BS EN 1176

Metric

Conversion:

50mm/ 2”

250mm/ 10”

350mm/ 14”

400mm/ 16”

450mm/ 18”

TX 45 Driver Bit

Tools:

(1.1)

Locate the Surface fix

Plate into the leg of the

instrument.

Fix instrument to Surface

fix plate using M10 bolt

and Barrel Nut and use

thread locking solution

to prevent fixings working

loose.

Fix Surface Plate to the

ground surface Ground

Anchors Not provided

cover fixings with caps

provided

12 3

Repeat Parts 1-3 for both legs

Thread Lock Solution

Required (Not Supplied)

M10 Barrel Nut

M10x50 Security Screw

Thread Lock Solution

Required (Not Supplied)

2 Part Cover Cap

Surface Fixed

1385mm

Ground Surface

Installation Instructions

M8x60 Security Screw

Surface Fix

Components: 20 Kg

Install Instrument

with 1.5m free space

(from widest point)

around it.

1.5m

Pair Small Red

Beaters X1

M10 Nut

M6x20 Security Screw

M6 Saddle Strap

Instrument

Components:

Flat Pack Harmony

Page 1 of 2

Weight of heaviest part 16kg (Harmony Frame)

BS EN 1176

Metric Conversion:

178mm/ 7”

250mm/ 10”

400mm/ 16”

1385mm/ 55”

1.5m/ 59”

CAUTION:

Harmony surface

can get hot in

direct sunlight, if

possible install in

shaded areas.

1. Unpack frame 3no.

2. Lay packaging out on floor

or assemble on non-abrasive

surface to prevent marking of

polished stainless steel.

3. Align holes on legs

(opposite end to polished

domes) and secure in place

using 3no. M10 x 200mm

threaded bar and 6no. M10

nuts provided

Tools required 2no. 17mm

metric spanner/wrench (11/16

inch or alternatively using

adjustable wrench)

4. Invert assembled frame so

domed ends face upwards.

5. Insert M8x60mm Security

screws into pre drilled holes

in frame using TX40 bit.

6. Attach Notes and Surface

Plate to Harmony Frame. (See

Assembly Guide Sheet)

7.Locate Harmony in desired

location and mark holes to fix

to desired surface.

8. Fix Surface Plate to level

surface using Coachscrews,

Rawlbolts, chemical anchors

or similar as deemed

appropriate by Installer.

(It is your responsibility to

ensure that the existing

surface is suitable to

receive the appropriate

fixing)

9. Make sure all fixings are

covered and secure using

cover caps provided

M8x25 Security Screw

2 Part Cover Cap

x4 Ground

Anchors not

supplied

Spares available from

percussionplay.com or from your

local distributor

Saddle Strap X3

M6x20 Pin torx X6

M8x60 Pin torx X2

COMPONENTS LIST:

Locate the Surface fix

Plate into the leg of the

instrument.

Fix instrument to Surface

fix plate using M8x25

Screws and use thread

locking solution to

prevent fixings working

loose.

Fix Surface Plate to the

ground surface Ground

Anchors Not provided

cover fixings with caps

provided

2 Part Cover Cap X8

M8x25 Pin torx X3

Surface Fixed

Instrument

Components:

M6x20 Security Screw

M6 Saddle Strap

TX 30 Driver Bit

Assembly Guide PPHARM

Surface Fix

Components: 20 Kg

Pair Small Red

Beaters X1

Harmony Flat Pack

Page 2 of 2

TX 40 Driver Bit

Tools:

BS EN 1176

Thread Lock Solution

Required

Thread Lock Solution

Required

Thread Lock Solution

Required

CAUTION:

Harmony surface

can get hot in

direct sunlight, if

possible install in

shaded areas.

M8x60 Security Screw

M8x25 Security Screw

2 Part Cover Cap

x4 Ground

Anchors not

supplied

Spares available from

percussionplay.com or from your

local distributor

Surface Fixed

2. Assemble Upper 3 Base

sections using M8 x 16 mm

CSK screws provided (1.1)

Installation Instructions

Tubular Bells will arrive on

site pre assembled

Ground Surface

90 Kg

Pair Large Red

Beaters X1

Instrument

Components:

Tubular Bells

are pre-

assembled

Weight of heaviest part 30kg (ALU Base)

Tubular Bells

Page 1 of 4

BS EN 1176

1.Locate Base in desired

location before attaching the

bells. Fix lower sections to

surface using pre drilled holes

provided. (Surface Anchors

Not supplied) Recommended

M10 Female Rawl Bolts or

chemical anchors

Spares available from

percussionplay.com or from your

local distributor

3. Using the M10x 40 screw

and Barrel Nuts to attach

each of the 9 legs to the base

(1.2)

1.2

4. Make sure that all fixings

are tightly secured and thread

locking solution used if

required.

1.1

M10 Barrel Nut

M10x40 Security Screw

M8x16 CSK Security Screw

x34

Surface Fix

Components:

Otros manuales para PPBDL-S

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento musical de Percussion Play

Percussion Play

Percussion Play Freechimes Diatonic Symphony Manual de usuario

Percussion Play

Percussion Play Mirror Chimes Manual de usuario

Percussion Play

Percussion Play Duo Manual de usuario

Percussion Play

Percussion Play Rainbow Trio Metallophone Manual de usuario

Percussion Play

Percussion Play Cadenza Manual de usuario

Percussion Play

Percussion Play Harmony Bells Manual de usuario

Percussion Play

Percussion Play PPCONG Manual de usuario

Percussion Play

Percussion Play CAVATINA Manual de servicio

Percussion Play

Percussion Play Soprano Pentatonic Manual de usuario

Percussion Play

Percussion Play Ground Fixed Manual de usuario

Percussion Play

Percussion Play Rainbow Trio Metallophone Manual de usuario

Percussion Play

Percussion Play Congas Manual de usuario

Percussion Play

Percussion Play Freechimes Pentatonic Symphony Manual de usuario

Percussion Play

Percussion Play Rainbow Trio Chimes Manual de usuario

Percussion Play

Percussion Play Ground Fixed Grand Marimba Manual de usuario

Percussion Play

Percussion Play TUTTI Manual de usuario

Percussion Play

Percussion Play Surface Fixed Manual de usuario

Percussion Play

Percussion Play Freechimes Alto Manual de usuario

Percussion Play

Percussion Play Surface Fixed Tubular Bells Manual de usuario

Percussion Play

Percussion Play Babel Drum Manual de servicio

Percussion Play

Percussion Play Freechimes Symphony Manual de usuario

Percussion Play

Percussion Play PPMIRC Manual de usuario

Percussion Play

Percussion Play Duo Manual de usuario

Percussion Play

Percussion Play Ground Fixed Marimba Manual de usuario

Manuales populares de Instrumento musical de otras marcas

Kawai

Kawai CN17 Manual de usuario

Yamaha

Yamaha PCY130 Manual de usuario

Korg

Korg SP-170S Manual de usuario

Roland

Roland ep-97 Manual de usuario

Roland

Roland LX-15 Manual de usuario

Johannus

Johannus Rembrandt 200 Manual de usuario

Yamaha

Yamaha Clavinova CVP-709 Manual de usuario

Yamaha

Yamaha YC-20 Manual de usuario

Yamaha

Yamaha Clavinova CVP-609 Manual de usuario

Casio

Casio celviano ap-700 Manual de usuario

Yamaha

Yamaha PSR-E473 Manual de usuario

Modulus

Modulus Quantum Series Manual de usuario

Gear4music

Gear4music SDP-4 Manual de usuario

HOMCOM

HOMCOM 390-006 Manual de usuario

Xotic Guitars

Xotic Guitars ProVintage Series Manual de usuario

Sadowsky

Sadowsky MetroLine Series Manual de usuario

Bosendorfer

Bosendorfer CEUS Manual de usuario

Gewa

Gewa UP 260 G Manual de usuario