Pentair Fleck 2850 Manual de usuario
Model 2850
Service Manual
IMPORTANT: Fill in Pertinent Information on Page 3 for Future Reference
Job Specication Sheet.........................................................................................................................................3
General Commercial Pre-Installation Check List...................................................................................................4
3200 Timer Setting Procedure............................................................................................................................... 5
3210 Timer Settings............................................................................................................................................... 6
3200 & 3210 Timer Series Regeneration Cycle Program Setting Procedure........................................................ 7
3200 Timer Assembly ............................................................................................................................................8
3200 Timer Assembly Parts List ............................................................................................................................9
3210 Timer Assembly ..........................................................................................................................................10
3210 Timer Assembly Parts List ...........................................................................................................................11
Control Valve with 1700 Injector Assembly..........................................................................................................12
Control Valve with 1700 Injector Assembly Parts List..........................................................................................13
Environmental Power Head Assembly ................................................................................................................14
Environmental Power Head Assembly Parts List ................................................................................................15
Control Drive Assembly ....................................................................................................................................... 16
Control Drive Assembly Parts List ....................................................................................................................... 17
Manual Drive Assembly & Parts List.................................................................................................................... 18
1600 Brine System Assembly & Parts List ..........................................................................................................19
1700 Brine System Assembly.............................................................................................................................. 20
1700 Brine System Assembly Parts List.............................................................................................................. 21
1710 Brine System Assembly & Parts List ..........................................................................................................22
1600 Service Valve Operator Assembly & Parts List...........................................................................................23
2300 Safety Brine Valve Assembly & Parts List ..................................................................................................24
2310 Safety Brine Valve Assembly & Parts List ..................................................................................................25
2350 Safety Brine Valve Assembly & Parts List ..................................................................................................26
1” Meter Assembly & Parts List ...........................................................................................................................27
1 1/2” Meter Assembly & Parts List .....................................................................................................................28
Service Assemblies .............................................................................................................................................30
Service Instructions .............................................................................................................................................32
General Service Hints for Meter Control..............................................................................................................33
Water Conditioner Flow Diagrams.......................................................................................................................34
Flow Data & Injector Draw Rates ........................................................................................................................ 36
System #4 - Typical Single Tank Installation with Optional Meter .......................................................................37
System #5 Interlock - Typical Twin Tank Installation with Optional Meter Interlock
and No Hard Water Bypass.................................................................................................................................38
System #6 - Twin Series Regeneration Installatio nwith a Remote Meter........................................................... 39
System #7 - Twin Alternator Installation with a Remote Meter ............................................................................40
System #4 - Single Valve Regeneration Immediate and Delayed Valve Wiring .................................................. 41
System #4 - with Remote Starter Valve Wiring.................................................................................................... 42
System #5 - Interlocked Regeneration Valve Wiring ........................................................................................... 43
System #6 - Series Regeneration Valve Wiring................................................................................................... 44
System #7 - Alternating Regeneration 230V / 3-Way Solenoid Output Valve Wiring .......................................... 45
System #7 - Alternating Regeneration 24V / 120V / 3-Way Solenoid Output Valve Wiring ................................. 46
Table of Contents
IMPORTANT: The information, specications and illustrations in this manual are based on the latest information
available at the time of printing. The manufacturer reserves the right to make changes at any time without notice.
*Job No.
*Model No.
*Water Test
*Capacity Per Unit
*Mineral Tank Size Diameter Height
*Brine Tank Size & Salt Setting per Regeneration
*2850 Control Valve Specications
1. Type of Timer
A. 7 Day or 12 Day
B. *625 to 10,625 Gallon Meter or
*3,125 to 53,125 Gallon Meter or
*Other
C. Meter Wiring Package
1. System #4 - 1 Tank, 1 Meter, Immediate or Delayed Regeneration
2. System #5 - 2 Tanks, 2 Meters, Interlock
3. System #6 - 2 Tanks, 1 Meter, Series Regeneration
4. System #7 - 2 Tanks, 1 Meter, Alternator
2. Timer Program Settings
A. Backwash Minutes
B. Brine & Slow Rinse Minutes
C. Rapid Rinse Minutes
D. Brine Tank Rell Minutes
3. Drain Line Flow Control gpm
4. Brine Line Flow Controller gpm
5. Injector Size #
6. Service Valve Operation Units (SVO)
Size of Service Valve
Page 3
Job Specication Sheet
General Commercial Pre-Installation Check List
Page 4
WATER PRESSURE: A minimum of 25 pounds of water pressure is required for regeneration valve to operate
effectively.
ELECTRICAL FACILITIES: A continuous 115 volt, 60 Hertz current supply is required. Make certain the current
supply is always hot and cannot be turned off with another switch.
EXISTING PLUMBING: Condition of existing plumbing should be free from lime and iron buildup. Piping that is
built up heavily with lime and/or iron should be replaced. If piping is clogged with iron, a separate iron lter unit
should be installed ahead of the water softener.
LOCATION OF SOFTENER AND DRAIN: The softener should be located close to a drain.
BY-PASS VALVES: Always provide for the installation of a by-pass valve.
CAUTION: Water pressure is not to exceed 120 p.s.i., water temperature is not to exceed 100° F, and the unit
cannot be subjected to freezing conditions.
Installation Instructions
1. Place the softener tank where you want to install the unit making sure the unit is level and on a rm base.
(Maximum 4 feet apart for twin units)
2. All plumbing should be done in accordance with local plumbing codes. The pipe size for the drain line should
be the same size as the drain line ow control connection. Water meters are to be installed on soft water
outlets. Twin units with 1 meter shall be installed on common soft water outlet of units.
3. Solder joints near the drain must be done prior to connecting the Drain Line Flow Control tting. Leave at
least 6” between the DLFC and solder joints when soldering when the pipes are connected on the DLFC.
Failure to do this could cause interior damage to the DLFC.
4. Teon tape is the only sealant to be used on the drain tting. The drain from twin units may be run through a
common line.
5. Make sure that the oor is clean beneath the salt storage tank and that it is level.
6 Place approximately 1” of water above the grid plate (if used) in your salt tank. Salt may be placed in the unit
at this time.
7. Place in by-pass position. Turn on the main water supply. Open a cold soft water tap nearby and let run a few
minutes or until the system is free from foreign material (usually solder) that may have resulted from the
installation.
8. Place the by-pass in service position.
9. Manually index the softener control into “service” position and let water ow into the mineral tank. When water
ow stops, close inlet valve, place control in “backwash” position to relieve head of air, then gradually open
inlet valve to purge remaining air in tank. Return control to service position.
10. Electrical: All electrical connections must be connected according to codes. Use electrical conduit if
applicable. Plug into power supply.
3200 Timer Setting Procedure
Page 5
How To Set Days On Which Water Conditioner Is To
Regenerate:
Rotate the skipper wheel until the number “1” is at the red
pointer. Set the days that regeneration is to occur by slid-
ing tabs on the skipper wheel outward to expose trip n-
gers. Each tab is one day. Finger at red pointer is tonight.
Moving clockwise from the red pointer, extend or retract
ngers to obtain the desired regeneration schedule.
How To Set The Time Of Day:
1. Press and hold the red button in to disengage the
drive gear.
2. Turn the large gear until the actual time of day is at
the time of day pointer.
3. Release the red button to again engage the drive
gear.
How To Manually Regenerate Your Water
Conditioner At Any Time:
1. Turn the manual regeneration knob clockwise.
2. This slight movement of the manual regeneration
knob engages the program wheel and starts the
regeneration program.
3. The black center knob will make one revolution in
the following approximately three hours and stop in
the position shown in the drawing.
4. Even though it takes three hours for this center knob
to complete one revolution, the regeneration cycle of
your unit might be set only one half of this time.
5. In any event, conditioned water may be drawn after
rinse water stops owing from the water
conditioner drain line.
How to Adjust Regeneration Time:
1. Disconnect the power source.
2. Locate the three screws behind the manual
regeneration knob by pushing the red button in and
rotating the 24 hour dial until each screw appears in
the cut out portion of the manual regeneration knob.
3. Loosen each screw slightly to release the pressure
on the time plate from the 24 hour gear.
4. Locate the regeneration time pointer on the inside
of the 24 hour dial in the cut out.
5. Turn the time plate so the desired regeneration time
aligns next to the raised arrow.
6. Push the red button in and rotate the 24 hour dial.
Tighten each of the three screws.
7. Push the red button and locate the pointer one more
time to ensure the desired regeneration time
is correct.
8. Reset the time of day and restore power to the unit.
3210 Timer Settings
Page 6
Typical Programming Procedure
Calculate the gallon capacity of the system, subtract
the necessary reserve requirement and set the gallons
available opposite the small white dot on the program
wheel gear.
NOTE: Drawing shows 8,750 gallon setting. The
capacity (gallons) arrow denotes remaining gallons
exclusive of xed reserve.
How To Set The Time Of Day:
Press and hold the red button in to disengage the
drive gear.
Turn the large gear until the actual time of day is
opposite the time of day pointer.
Release the red button to again engage the drive
gear.
1.
2.
3.
How To Manually Regenerate Your Water Condi-
tioner At Any Time:
Turn the manual regeneration knob clockwise.
This slight movement of the manual regeneration
knob engages the program wheel and starts the
regeneration program.
The black center knob will make one revolution in
the following approximately three hours and stop in
the position shown in the drawing.
Even though it takes three hours for this center
knob to complete one revolution, the regeneration
cycle of your unit might be set for only one half of
this time.
In any event, conditioned water may be drawn after
rinse water stops owing from the water conditioner
drain line.
Immediate Regeneration Timers:
These timers do not have a 24 hour gear. Setting the
gallons on the program wheel and manual regeneration
procedure are the same as previous instructions.
1.
2.
3.
4.
5.
NOTE: To set meter capacity
rotate manual knob one - 360°
revolution to set gallonage.
3200 & 3210 Timer Series
Regeneration Cycle Program Setting Procedure
(Brine Tank Rell Separate from Rapid Rinse)
Page 7
How To Set The Regeneration Cycle Program:
The regeneration cycle program on your water condi-
tioner has been factory preset, however, portions of
the cycle or program may be lengthened or shortened
in time to suit local conditions.
3200 & 3210 Series Timers (Figure to Right)
To expose cycle program wheel, grasp timer in
upper left-hand corner and pull, releasing snap
retainer and swinging timer to the right.
To change the regeneration cycle program, the
program wheel must be removed. Grasp program
wheel and squeeze protruding lugs toward cen-
ter, lift program wheel off timer. (Switch arms may
require movement to facilitate removal)
Return timer to closed position engaging snap
retainer in back plate. Make certain all electrical
wires locate above snap retainer post.
Timer Setting Procedure for 3200 & 3210
Timer
How To Change The Length Of The Backwash
Time:
The program wheel as shown in the drawing is in the
service position. As you look at the numbered side of
the program wheel, the group of pins starting at zero
determines the length of time your unit will backwash.
EXAMPLE: If there are six pins in this section, the time
of backwash will be 12 min. (2 min. per pin). To change
the length of backwash time, add or remove pins as
required. The number of pins times two equals the
backwash time in minutes.
How To Change The Length Of Brine And Rinse
Time:
The group of holes between the last pin in the
backwash section and the second group of pins
determines the length of time that your unit will
brine and rinse (2 min. per hole.)
To change the length of brine and rinse time, move
the rapid rinse group of pins to give more or fewer
holes in the brine and rinse section. Number of
holes times two equals brine and rinse time in
minutes.
1.
2.
3.
1.
2.
How To Change The Length Of Rapid Rinse:
The second group of pins on the program wheel
determines the length of time that your water condi-
tioner will rapid rinse. (2 min. per pin.)
To change the length of rapid rinse time, add or
remove pins at the higher numbered end of this
section as required. The number of pins times two
equals the rapid rinse time in minutes.
How To Change The Length Of Brine Tank Rell
Time:
The second group of holes in the program wheel
determines the length of time that your water condi-
tioner will rell the brine tank (2 min. per hole.)
To change the length of rell time, move the two
pins at the end of the second group of holes as
required.
The regeneration cycle is complete when the outer
microswitch is tripped by the two pin set at end of
the brine tank rell section.
The program wheel, however, will continue to rotate
until the inner micro-switch drops into the notch on
the program wheel.
1.
2.
1.
2.
3.
4.
Page 8
3200 Timer Assembly
Page 9
3200 Timer Assembly Parts List
1...................1....................13870.................. Housing, Timer, 3200
2...................1....................13011..................Arm, Cycle Actuator
3...................1....................40096-24............. Dial 12AM Regen Assy, Black
40096-02.............Dial 2AM Regen Assy, Black
4...................1....................13886.................. Knob, 3200
5...................5....................13296.................. Screw, Hex Wsh, 6-20 x 1/2 Type 25 Steel Zinc
6...................1....................11999..................Label, Button
7...................1....................14381.................. Skipper Wheel Assy, 12 Day
14860..................Skipper Wheel Assy, 7 Day
8...................1....................13014.................. Pointer, Regeneration
9...................1....................14265.................. Clip, Spring
10.................2....................13311..................Spring, Detent, Timer
11.................2....................13300.................. Ball, 1/4” SS
12.................1....................15424.................. Spring, Detent, Timer
13.................1....................13911..................Gear, Main Drive, Timer
14.................1....................19210.................. Program Wheel Assy, 3200
15.................21..................15493.................. Pin, Spring, 1/16 x 5/8 SS
16.................1....................13018.................. Pinion, Idler
17.................1....................13312.................. Spring, Idler Shaft
18.................1....................13017.................. Gear, Idler
19.................1....................13164.................. Gear, Drive
20.................1....................13887.................. Plate, Motor Mounting
21.................1....................18743-1............... Motor, 120V, 60Hz 1/30 RPM, 5600
19659-1...............Motor, 24V, 60 Hz 1/30 RPM
22.................2....................13278.................. Screw, Phil Hd Mach, 6-32 x 1/8 Steel Zinc
23.................3....................11384..................Screw, Phil, 6-32 x 1/4 Zinc
24.................1....................13881.................. Bracket, Hinge Timer
25.................3....................14087.................. Insulator
26.................1....................10896.................. Switch, Micro
27.................1....................15320.................. Switch, Micro, Timer
28.................2....................11413..................Screw, Pan Hd Mach, 4-40 x 1 1/8 MS Steel Zinc
29.................1....................14007.................. Label, Time of Day
30.................1....................14045.................. Label, Instruction
31.................1....................13864.................. Ring, Skipper Wheel
32.................1....................15066.................. Ball, 1/4” Delrin
Not Shown ...1....................13902.................. Harness, 3200
Not Shown ...2....................40422.................. Nut, Wire, Tan
Not Shown ...1....................15354-01............. Wire, Ground 4”
3210 Timer Assembly
Page 10
Otros manuales para Fleck 2850
1
Tabla de contenidos
Otros manuales de Unidad de control de Pentair
Pentair
Pentair Fleck 5800 LXT Guía del usuario
Pentair
Pentair AUTOTROL 363 Manual de usuario
Pentair
Pentair FLECK 5810 XTR2 Manual de usuario
Pentair
Pentair E-Box MAESTRO Lite Instrucciones de funcionamiento
Pentair
Pentair E-Box MAESTRO Instrucciones de funcionamiento
Pentair
Pentair F251 Instrucciones de instalación y funcionamiento
Pentair
Pentair BAA A390-D.03 Select Manual de usuario
Pentair
Pentair Keystone Figure 952 NPS 2 Instrucciones de instalación
Pentair
Pentair FLECK NXT Manual de usuario
Pentair
Pentair FLECK 3150 NXT Guía del usuario
Pentair
Pentair AUTOTROL 740 Manual de usuario
Pentair
Pentair AUTOTROL Performa 263 Guía del usuario
Pentair
Pentair SIATA V132-SFE Manual de usuario
Pentair
Pentair AUTOTROL 368 Manual de usuario
Pentair
Pentair Goyen Precision P1 Manual de usuario
Pentair
Pentair FLECK 2850 SXT Manual de usuario
Pentair
Pentair FLECK PROFLOSXT DOWNFLOW Manual de usuario
Pentair
Pentair FLECK 7000XTR Manual de usuario
Pentair
Pentair FLECK 9100 SXT Manual de usuario
Pentair
Pentair FLECK3150 DOWNFLOW Manual de usuario
Manuales populares de Unidad de control de otras marcas
Festo
Festo Compact Performance CP-FB6-E Manual de lista de piezas
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manual de usuario
JS Automation
JS Automation MPC3034A Manual de usuario
JAUDT
JAUDT SW GII 6406 Series Guía rápida
Spektrum
Spektrum Air Module System Manual de usuario
BOC Edwards
BOC Edwards Q Series Manual de usuario
