peerless-AV DS-C560-2X2 Manual de usuario
12014-04-14 #:009-9082-11 (2018-06-15)
ENG
DS-C560-2X2
46" - 55"
(117 - 140 cm)
500 lb
(227 kg)
MAX
22014-04-14 #:009-9082-11 (2018-06-15)
To properly tighten screws: Tighten until screw
head makes contact, then tighten another 1/2
turn. Do not overtighten screws.
1
2
+1/2
4
3
Symbols
ENG
WARNING
ENG
Display center.
ENG
x3
Screws must get at
least three full turns
and t snug.
ENG
Do not overtighten screws.
ENG
ENG - Do not begin to install product until you have read and understood the instructions and warnings
contained in this user guide. Always use an assistant or mechanical lifting equipment to safely lift and position
equipment. This product must be installed onto at, hard, level surface to prevent tipping. Use with heavier
displays may result in instability causing tip over resulting in death or serious injury. The cart or stand is not
afxed or secured to the oor, and may therefore tip over and/or fall if screen and/or stand is shaken or hit. This
product is intended for indoor use only. Use of this product outdoors could lead to product failure or personal
injury. Screws must be tightly secured. Do not overtighten screws or damage can occur and product may fail.
Never exceed the Maximum Load Capacity. Be careful not to pinch ngers when operating the mount. Death or
serious injury may occur when children climb on audio and/or video equipment furniture. A remote control or toys
placed on the furnishing may encourage a child to climb on the furnishing and as a result the furnishing may tip
over on to the child. Relocating audio and/or video equipment to furniture not specically designed to support
audio and/or video equipment may result in death or serious injury due to the furnishing collapsing or over turning
onto a child. For support please call customer care at 1-800-865-2112.
WARNING
32014-04-14 #:009-9082-11 (2018-06-15)
Parts List
Part #Description Qty
Acaster, 5" swivel 4 600-0026
Bcaster support 4 145-T1799
Ccover 6 145-T1809
Dbase leg 2 145-T1767
Ehorizontal leg support 1 145-T1785
Fbase support tube 2 145-T1812
Gbase support 8 560-T1261
Hvertical leg support 2 146-T1131
Ileft adaptor bracket 4 146-1609
Jright adaptor bracket 4 146-1608
Kvertical support bracket 4 145-T1806
Lcomputer cover 1 145-T1930
Mcomputer shelf 1 145-T1931
Ndual rail assembly 2 146-T1905
Ocord bracket 4 146-T1321
Pknurled knob 4 560-1160
QM8 x 16mm socket button screw 104 520-9527
RM8 square nut 32 530-1066
Scover clip 24 590-0317
TM5 x 10mm type-f, socket pin screw 10 520-1164
Ubar nut 16 146-1319
V1/4" power bit 1 560-0263
W5mm allen wrench 1 560-9640
Xnylon shoulder washer 16 590-2233
YM6 x 12mm socket pin screw 16 520-1050
Z4mm allen wrench 1 560-9646
Parts (Before beginning, make sure you have all parts shown below).
D (2)
base leg
A (4)
caster
B (4)
caster support
C (6)
cover
E (1)
horizontal leg
support
F (2)
base support
tube
G (8)
base support
H (2)
vertical leg
support
K (4)
vertical support
bracket
J (4)
right adaptor
bracket
I (4)
left adaptor
bracket
42014-04-14 #:009-9082-11 (2018-06-15)
L (1)
computer cover
N (2)
dual rail
assembly
Q (104)
M8 x 16mm
R (32)
M8 square nut
S (24)
cover clip
T (10)
M5 x 10mm
V (1)
1/4" power
bit
W (1)
5mm allen
wrench
nylon shoulder
washer
X (16)
M6 x 12mm
Y (16)
4mm allen
wrench
Z (1)
M (1)
computer shelf
O (4)
cord
bracket
P (4)
knurled
knob
bar nut
U (16)
52014-04-14 #:009-9082-11 (2018-06-15)
1-1
Q (4)
A
B
Q (2)
R (2)
Do not fully tighten hardware
SIDE VIEW
x4
1-2
x4
W
W
62014-04-14 #:009-9082-11 (2018-06-15)
2
Q (4)
Q (4)
F
F
R (4)
R (4)
D
R (4)
x2 W
72014-04-14 #:009-9082-11 (2018-06-15)
4
SIDE VIEW
Do not fully tighten hardware
Casters must be ush to end of horizontal leg support.
ENG
x8 U (2)
G
Q (4)
3
TIGHTEN
CONNECTING
HARDWARE
FLUSH
EDGES
ENG
x2
W
W
82014-04-14 #:009-9082-11 (2018-06-15)
5
H
6
TIGHTEN
CONNECTING
HARDWARE
TIGHTEN
CONNECTING
HARDWARE
E
x2
LOCK WHEELS
W
W
92014-04-14 #:009-9082-11 (2018-06-15)
7-1
7-2
DISPLAY HEIGHT
K (4)
Q (6)
R (4)
K
1/8"
(3mm)
1/8"
(3mm)
x4
W
W
TIGHTEN
CONNECTING
HARDWARE
10 2014-04-14 #:009-9082-11 (2018-06-15)
8
N
Cross supports must center on vertical leg supports.
TIGHTEN
CONNECTING
HARDWARE (X4)
W
Tighten.
ENG Tighten.
ENG
Tabla de contenidos
Otros manuales de Rack y soporte de peerless-AV
peerless-AV
peerless-AV ACC002 Manual de usuario
peerless-AV
peerless-AV LCW620AD Guía
peerless-AV
peerless-AV SR898 Manual de usuario
peerless-AV
peerless-AV DS-VW655-2X2 Manual de usuario
peerless-AV
peerless-AV ACCXT201 Guía
peerless-AV
peerless-AV SMARTMAUNT Series Manual de instrucciones
peerless-AV
peerless-AV PWA-14 Manual de usuario
peerless-AV
peerless-AV PLAV 70-UNL Guía
peerless-AV
peerless-AV SA752PU Manual de usuario
peerless-AV
peerless-AV DS-LEDA27 Series Manual de usuario
peerless-AV
peerless-AV MOD-FCS2KIT300 Manual de usuario
peerless-AV
peerless-AV SR598ML3T Manual de usuario
peerless-AV
peerless-AV PTM400 Guía
peerless-AV
peerless-AV RMI2W Manual de usuario
peerless-AV
peerless-AV SmartMount ST16D Guía
peerless-AV
peerless-AV DS-LEDA27-10X10 Manual de usuario
peerless-AV
peerless-AV SR575K Manual de usuario
peerless-AV
peerless-AV CM50 Guía
peerless-AV
peerless-AV EWL-OH85F Manual de usuario
peerless-AV
peerless-AV SMARTMOUNT XT SFX645P Manual de usuario
