PeakTech 1007 Manual de usuario
1
Operating Manual
2
3
Table of Content
1. Introduction 4
1.1 General 4
1.2 Key Features 4
1.3 Physical Description 5
1.4 Specification 7
2. Operation 11
2.1 Keypad and Knob Description 11
2.2 Opening Screen 13
2.3 Setting Group Name 13
2.4 Adjust Frequency 14
2.5 Select Waveform 14
2.6 Frequency Sweep 15
2.7 Output Attenuation 18
2.8 Rotary Frequency Step Setting 19
2.9 Amplitude, Offset and Square Wave Pulse Width Display 20
2.10 Trigger/Gate 21
2.11 Phase-Shift Keying (PSK) and Frequency-Shift Keying (FSK) Modulation 22
2.12 Sub Function 24
2.13 Notice of Operating 28
4
1. Introduction
1.1 General
The PeakTech®1007 / 1014 / 1016 series is a high-performance direct digital synthesize (DDS)
function generator with very low noise and distortion. Combined with the DDS technology, the
FG700S/F series can output high accuracy and stable frequency to meet your test requirement
of precision and accuracy. The build-in trigger/gate function allows you to control the waveform
generation by internal or external. Also, the PSK and FSK modulation gives you the ability to
generate such waveform for experiment or communication purpose. The FG700F series comes
with AM/FM module and frequency counter to make the function of this product more
comprehensive.
1.2 Key Features
• Direct digital synthesize multi-function generator
• Sine, square, triangle, pulse, DC, synchronize and ramp up/ramp down output
(only P 1014 / 1016)
• Ultra low noise and low distortion (down to 1mV peak signal)
• PSK and FSK modulation
• Digital setting of linear or logarithm sweep function
• Trigger and gate function
• AM/FM module (only P 1014 / 1016)
• Frequency counter (only P 1014 / 1016)
5
1.3 Physical Description
PeakTech®1007 Front Panel
6
PeakTech®1014 / 1016 Front Panel
Rear Panel
7
1 Liquid Crystal Display 13 Square Wave Pulse Width Adjustment
Knob
2 Keypad 14 Sync Output Connector (TTL level with
50Ωoutput impedance)
3 Square Wave Pulse Width
Adjustment On/Off Indicator
15 Power Switch
4 Output Offset On/Off Indicator 16 Adjustable Feet
5 Output Amplitude Attenuation Range
Indicator
17 Air Ventilation Holes
6 External/Internal indicator of
Trigger/Gate or PSK/FSK
18 Power-line Fuse Holder
7 Rotary with Push Button 19 Power-line AC Input Socket
8 Handle 20 Chassis Terminal
9 Function Output BNC Connector
(50Ωoutput impedance)
21 Protective Earth (Ground) Terminal
10 External input BNC Connector for
Trigger/Gate and PSK/FSK
(CMOS level)
22 External Modulation Input (5.5Vp Max.)
for AM/FM Function
11 Amplitude Adjustment Knob 23 External Frequency Input (5Vrms Max.
@ 50Ω) for Frequency Counter Function
12 DC/Offset Adjustment Knob 24 Internal AM/FM Adjustment Knob
1.4 Specification
PeakTech®1007 Output Characteristics
a. Frequency Range Sine, Square, Pulse and
Sync Output :
Triangle :
100mHz ~ 8MHz
100mHz ~ 1MHz
b. Frequency Resolution 100mHz or 6 digits display
c. Output Impedance 50Ω±5%
d. Amplitude 1mV to 20Vp-p (open-circuit)
0.5mV to 10Vp-p (into 50Ωload)
e. Amplitude Resolution 2~3 digits, 1mV min (depending on the attenuation)
f. Amplitude Accuracy Typical 1% test at 1KHz 9Vp-p sine @ 50Ωload
g. Output Attenuation 0, -20, -40 and -60 dB
h. FUNC_OUT Self Protection FUNC_OUT short circuit protection
Reverse voltage protection below 20Vpeak
i. DC Offset and DC Output ±10V at open-circuit, ±5V at 50Ωload
j. DC Output Resolution 2 digits, ±1mV min (depending on the attenuation)
k. DC Output Accuracy 1% ±5 counts
l. Sine Wave Harmonic Distortion DC ~ 100KHz < -55dBc typical
100KHz to 1MHz < -45dBc typical
1MHz ~ 8MHz < -35dBc typical
m. Spurious (non harmonic) DC ~ 1MHz < -55dBc typical
n. Total Harmonic Distortion DC ~ 100KHz < 0.3%
o. Square Wave rise / fall time ≤12nS for 10Vp-p @ 50Ωload
overshoot < 5% of Vp for 10Vp-p @ 50Ωload
8
p. Pulse
(analogue control)
Frequency range :
Amplitude :
Duty cycle :
100mHz ~ 8MHz
0 ~ 10V / 0 ~ -10V / ±10V
100mHz ~ 6MHz : 20% to 80%
6MHz ~ 8MHz : 40 % to 60%
q. Triangle Wave Linearity 99% up to 100KHz
r. Sweep (Linear / Logarithm) Start frequency, stop frequency and sweep step
setting
Sweep type : up, down and up-down
s. Sync Output Frequency
range : Output
level :
Output
impedance
100mHz ~ 8MHz
low level ≤0.6V @ 50Ωhigh level
≥1V @ 50Ω
50Ω
Modulation Characteristics
a. FSK Function
Frequency range
Internal rate
Source
Sine, Square or Triangle
100mHz ~ 8MHz
400Hz / 1000Hz
Internal / External
b. PSK Function
Frequency range
Phase setting
Internal rate
Source
Sine, Square or Triangle
100mHz ~ 8MHz
0.0000 to 360.0 degree
400Hz / 1000Hz
Internal / External
Trigger/Gate Characteristics
a. Trigger Source Main frequency setting Manual (rotary push) / External:
100mHz ~ 100KHz
b. Gate Source Main frequency setting Manual (rotary push) / External:
100mHz ~ 8MHz
General Characteristics
a. Power Source AC 115V / 230V (on request) ±10%, 50Hz / 60Hz
b. Temperature 0ºC ~ 40ºC (Operation) -20ºC ~ 70ºC (Storage)
c. Relative Humidity up to 80%
d. Dimension 95mm (H) x 235mm (W) x 280mm(D)
e. Weight 3kg
f. Accessories AC power cord, operating manual
PeakTech®1014 / 1016 Output Characteristics
a. Frequency
Range
Sine, Square, Pulse and Sync
Output : Triangle :
Ramp Up, Ramp Down :
100mHz ~ 10MHz (P 1014)
100mHz ~ 20MHz (P 1016)
100mHz ~ 1MHz
100mHz ~ 20KHz
b. Frequency
Resolution
100mHz or 6 digits display
9
c. Output
Impedance
50Ω±5%
d. Amplitude 1mV to 20Vp-p (open-circuit)
0.5mV to 10Vp-p (into 50Ωload)
e. Amplitude
Resolution
3 digits, 1mV min (depending on the attenuation)
f. Amplitude
Accuracy
Typical 1% test at 1KHz 9Vp-p sine @ 50Ωload
g. Output
Attenuation
0, -20, -40 and -60 dB
h. FUNC_OUT Self
Protection
FUNC_OUT short circuit protection
Reverse voltage protection below 20Vpeak
i. DC Offset and
DC Output
±10V at open-circuit, ±5V at 50Ωload
j. DC Output
Resolution
3 digits, ±1mV min (depending on the attenuation)
k. DC Output
Accuracy
1% ±5mV
l. Sine Wave
Harmonic
Distortion
DC ~ 100KHz < -55dBc typical
100KHz to 1MHz < -45dBc typical
1MHz ~ **MHz < -35dBc typical
m. Spurious (non
harmonic)
DC ~ 1MHz < -55dBc typical
n. Total Harmonic
Distortion
DC ~ 100KHz < 0.3%
o. Square Wave rise / fall time 12nS for 10Vp-p @ 50Ωload overshoot < 5% of Vp for
10Vp-p @ 50Ωload
p. Pulse (digital
control)
Frequency range
Amplitude
200mHz ~ 20KHz
20KHz ~ 200KHz
0 ~ 10V / 0 ~ -10V / ±10V
Duty cycle 200mHz ~ 20KHz 1uS ~ 4.995S
20KHz ~ 200KHz 1uS ~ 494.9uS
q. Triangle Wave
Linearity
99% up to 100KHz
r. Sweep
(Linear /
Logarithm)
Start frequency, stop frequency and sweep step setting
Sweep type : up, down and up-down
s. Sync Output Frequency range
Output level
Output impedance
100mHz ~ 10MHz (P 1014)
100mHz ~ 20MHz (P 1016)
low level ≤0.6V @ 50Ω
high level ≥1V @ 50Ω
50Ω
10
Modulation Characteristics
a. AM Function
Modulation ratio
Source
Internal source
External source
Sine or Triangle
0% ~ 100%
Internal/External
400Hz/1000Hz Sine Wave
Max. 5.5Vpeak any waveform
b. FM Function
Frequency range
Peak deviation
Source
Internal source
External source
Sine, Suqare or Triangle
100mHz ~ 10KHz
4 ~ 5% of Max. frequency
Internal/External
400Hz/1000Hz Sine Wave
Max. 5.5Vpeak any waveform
c. FSK Function
Frequency range
Internal rate
Source
Sine, Square or Triangle
100mHz ~ 10MHz (P 1014)
100mHz ~ 20MHz (P 1016)
400Hz / 1000Hz
Internal / External
d. PSK Function
Frequency range
Phase setting
Internal rate
Source
Sine, Square or Triangle
100mHz ~ 10MHz (P 1014)
100mHz ~ 20MHz (P 1016)
0.0000 to 360.0 degree
400Hz / 1000Hz
Internal / External
Trigger/Gate Characteristics
a. Trigger Source
Main frequency setting
Manual (rotary push) / External
100mHz ~ 100KHz
b. Gate Source
Main frequency setting
Manual (rotary push) / External
100mHz ~ 10MHz (P 1014)
100mHz ~ 20MHz (P 1016)
Frequency Counter
a. Range 2Hz to 100MHz
b. Accuracy ±5 counts
c. Resolution 7 digits or (99.9999)
d. Low pass filter Manual activate
e. Timebase accuracy 50MHz ±25 ppm (23.5 ±5 ˚C) or TCXO optional
f. Input Attenuation 0dB, 20dB
g. Sensitivity 2Hz ~ 50MHz/-20dBm @ 50Ωtypical
50MHz ~ 80MHz/-10dBm @ 50Ωtypical
80MHz ~ 100MHz/-5dBm @ 50Ωtypical
General Characteristics
a. Power Source AC 115V / 230V (on request) ±10%, 50Hz / 60Hz
b. Temperature 0ºC ~ 40ºC (Operation); -20ºC ~ 70ºC (Storage)
c. Relative Humidity up to 80%
d. Dimension 95mm (H) x 235mm (W) x 280mm(D)
e. Weight 3kg
f. Accessories AC power cord, operating manual
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Inversor de PeakTech
