PCB Piezotronics IMI Sensors 687A01 Manual de usuario

Model 687A01

Handheld Vibration Meter Kit

Installation and Operating Manual

This manual contains the 080A131, 603C01, 687A02 installation and operating manuals

that comprise a Model 687A01 Handheld Vibration Meter Kit.

For assistance with the operation of this product,

contact PCB Piezotronics, Inc.

Toll-free: 800-959-4464

24-hour SensorLine: 716-684-0001

Fax: 716-684-3823

E-mail: [email protected]

Web: www.imi-sensors.com

The information contained in this document supersedes all similar information that

may be found elsewhere in this manual.

Service –Due to the sophisticated

nature of the sensors and associated

instrumentation provided by PCB

Piezotronics, user servicing or repair is

not recommended and, if attempted,

may void the factory warranty. Routine

maintenance, such as the cleaning of

electrical connectors, housings, and

mounting surfaces with solutions and

techniques that will not harm the

physical material of construction, is

acceptable. Caution should be observed

to ensure that liquids are not permitted

to migrate into devices that are not

hermetically sealed. Such devices

should only be wiped with a dampened

cloth and never submerged or have

liquids poured upon them.

Repair –In the event that equipment

becomes damaged or ceases to

operate, arrangements should be made

to return the equipment to PCB

Piezotronics for repair. User servicing or

repair is not recommended and, if

attempted, may void the factory

warranty.

Calibration –Routine calibration of

sensors and associated instrumentation

is recommended as this helps build

confidence in measurement accuracy

and acquired data. Equipment

calibration cycles are typically

established by the users own quality

regimen. When in doubt about a

calibration cycle, a good “rule of thumb”

is to recalibrate on an annual basis. It is

also good practice to recalibrate after

exposure to any severe temperature

extreme, shock, load, or other

environmental influence, or prior to any

critical test.

PCB Piezotronics maintains an ISO-

9001 certified metrology laboratory and

offers calibration services, which are

accredited by A2LA to ISO/IEC 17025,

with full traceability to SI through

N.I.S.T. In addition to the normally

supplied calibration, special testing is

also available, such as: sensitivity at

elevated or cryogenic temperatures,

phase response, extended high or low

frequency response, extended range,

leak testing, hydrostatic pressure

testing, and others. For information on

standard recalibration services or

special testing, contact your local PCB

Piezotronics distributor, sales

representative, or factory customer

service representative.

Returning Equipment –Following

these procedures will ensure that your

returned materials are handled in the

most expedient manner. Before

returning any equipment to PCB

Piezotronics, contact your local

distributor, sales representative, or

factory customer service representative

to obtain a Return Warranty, Service,

Repair, and Return Policies and

Instructions Materials Authorization

(RMA) Number. This RMA number

should be clearly marked on the outside

of all package(s) and on the packing

Service, Repair, and Return

Policies and Instructions

list(s) accompanying the shipment. A

detailed account of the nature of the

problem(s) being experienced with the

equipment should also be included

inside the package(s) containing any

returned materials.

A Purchase Order, included with the

returned materials, will expedite the

turn-around of serviced equipment. It is

recommended to include authorization

on the Purchase Order for PCB to

proceed with any repairs, as long as

they do not exceed 50% of the

replacement cost of the returned

item(s). PCB will provide a price

quotation or replacement

recommendation for any item whose

repair costs would exceed 50% of

replacement cost, or any item that is not

economically feasible to repair. For

routine calibration services, the

Purchase Order should include

authorization to proceed and return at

current pricing, which can be obtained

from a factory customer service

representative.

Contact Information –International

customers should direct all inquiries to

their local distributor or sales office. A

complete list of distributors and offices

can be found at www.pcb.com.

Customers within the United States may

contact their local sales representative

or a factory customer service

representative. A complete list of sales

representatives can be found at

www.pcb.com. Toll-free telephone

numbers for a factory customer service

representative, in the division

responsible for this product, can be

found on the title page at the front of this

manual. Our ship to address and

general contact numbers are:

PCB Piezotronics, Inc.

3425 Walden Ave.

Depew, NY14043 USA

Toll-free: (800) 828-8840

24-hour SensorLineSM: (716) 684-0001

Website: www.pcb.com

E-mail: [email protected]

PCB工业监视和测量设备 - 中国RoHS2公布表

PCB Industrial Monitoring and Measuring Equipment - China RoHS 2 Disclosure Table

部件名称

有害物质

铅(Pb)

汞

(Hg)

镉

(Cd)

六价铬(Cr(VI))

多溴联苯 (PBB)

多溴二苯醚(PBDE)

住房

PCB板

电气连接器

压电晶体

环氧

铁氟龙

电子

厚膜基板

电线

电缆

塑料

焊接

铜合金/黄铜

本表格依据 SJ/T 11364 的规定编制。

O：表示该有害物质在该部件所有均质材料中的含量均在 GB/T 26572 规定的限量要求以下。

X：表示该有害物质至少在该部件的某一均质材料中的含量超出 GB/T 26572 规定的限量要求。

铅是欧洲RoHS指令2011/65/ EU附件三和附件四目前由于允许的豁免。

CHINA RoHS COMPLIANCE

DOCUMENT NUMBER: 21354

DOCUMENT REVISION: D

ECN: 46162

Component Name

Hazardous Substances

Lead

(Pb)

Mercury

(Hg)

Cadmium

(Cd)

Chromium VI

Compounds

(Cr(VI))

Polybrominated

Biphenyls

(PBB)

Polybrominated

Diphenyl

Ethers (PBDE)

Housing

PCB Board

Electrical

Connectors

Piezoelectric

Crystals

Epoxy

Teflon

Electronics

Thick Film

Substrate

Wires

Cables

Plastic

Solder

Copper Alloy/Brass

This table is prepared in accordance with the provisions of SJ/T 11364.

O: Indicates that said hazardous substance contained in all of the homogeneous materials for this part is below the limit

requirement of GB/T 26572.

X: Indicates that said hazardous substance contained in at least one of the homogeneous materials for this part is above

the limit requirement of GB/T 26572.

Lead is present due to allowed exemption in Annex III or Annex IV of the European RoHS Directive 2011/65/EU.

INDUSTRIAL MONITORIN

G INSTRUMENTATION DI

VISION

SENSORS AND INSTRUME

NTATION FOR MACHINE

CONDITION MONITORING

The Model 687A01 & 687A02 Hand Held Vibration Meter Kits

Operating Guide with Enclosed Warranty Information

3425 Walden Avenue, Depew, New York 14043-2495

Phone (716) 684-0003

Fax (716) 684-3823

Toll Free Line 1-800-959-4IMI

MANUAL NUMBER: 18411

MANUAL REVISION: B

ECN NUMBER: 18769

INDUSTRIAL MONITORIN

G INSTRUMENTATION DI

VISION

PAGE 2

SENSORS AND INSTRUME

NTATION FOR MACHINE

CONDITION MONITORING

table of contents

Introduction...................................................................................................................... page 3

Figure 1 –Model 687A01 Hand Held Vibration Meter Kit............................................ page 3

Description....................................................................................................................... page 4

Sensor –Model 603C01................................................................................................... page 5

Headphones –Model 070A47 .......................................................................................... page 5

Magnetic Mounting Base –Model 080A131 ..................................................................... page 5

Cable Assembly –Model 050BQ006AC........................................................................... page 5

ESD Warning Information................................................................................................ page 6

warranty/servicing

Warranty, Service & Return Procedure............................................................................ page 7

Customer Service............................................................................................................ page 8

INDUSTRIAL MONITORIN

G INSTRUMENTATION DI

VISION

PAGE 3

SENSORS AND INSTRUME

NTATION FOR MACHINE

CONDITION MONITORING

introduction

The Model 687A01 Hand Held Vibration Meter Kit consists of a digital vibration meter, a general purpose

accelerometer, an accelerometer cable assembly, magnet, and headphones. The kit is designed for general

purpose, overall vibration readings on all types of machines. When unpacking the kit, be sure to note that the

following accessories are included:

687A02 Meter

603C01 Industrial Accelerometer

050BQ006AC Cable Assembly

080A131 Magnetic Mounting Base

070A47 Headphones

figure 1 - model 687A01 hand held vibration meter kit

INDUSTRIAL MONITORIN

G INSTRUMENTATION DI

VISION

PAGE 4

SENSORS AND INSTRUME

NTATION FOR MACHINE

CONDITION MONITORING

description

The meter provides two types of measurements —overall acceleration and overall velocity. In the velocity mode,

the meter measures in the frequency range of 10 Hz to 1 kHz, and complies with ISO2954 standard. It measures

overall RMS velocity to a maximum of two inches per second. In acceleration mode, the meter measures in the

frequency range of 50 Hz to 50 kHz. The maximum overall RMS acceleration reading is 20 g’s. To toggle

between acceleration and velocity measurements, use the rocker switch labeled “ACC/VEL.”To turn the unit on,

move the rocker switch labeled “0/I/Bias”to the “I”position. The “0”position shuts the unit off, while the bias is a

momentary toggle for monitoring the bias voltage of the sensor.

The meter provides three input connectors that are located at the top of the unit. The input for the sensor (labeled

SENSOR) is a standard BNC Jack. The headphones can be connected through the 1/8 inch stereo jack (labeled

with the appropriate symbol), and the input for the recharger (labeled CHARGE) is a 2.5 mm plug.

The unit is powered by a 9-volt alkaline battery which is housed in the battery compartment located at the bottom

of the meter. To remove this cover, use a small standard screwdriver, pry the cover up, and the push it up

towards the top of the meter. Since the meter is supplied with alkaline batteries, DO NOT ATTEMPT TO

RECHARGE ALKALINE BATTERIES. IT MAY CAUSE A POTENTIAL FIRE AND/OR EXPLOSION.

The unit has a low battery indicator on the front panel LCD display. The indicator will light when the battery

voltage is approximately 7.5 volts. Please replace the battery or recharge the rechargeable battery if supplied.

If the optional recharger was purchased, plug-in the recharger in the appropriate connector located on the top of

the meter. Turn unit off, and plug the charger into an electrical outlet. Recharge the battery for approximately 12

hours.

INDUSTRIAL MONITORIN

G INSTRUMENTATION DI

VISION

PAGE 5

SENSORS AND INSTRUME

NTATION FOR MACHINE

CONDITION MONITORING

sensor –model 603C01

The sensor supplied with the kit is a general purpose industrial accelerometer, Model 603C01. Please refer to the

enclosed specifications on the 603C01 for proper operation of the sensor.

headphones –model 070A47

The headphones are stereo-type with built-in, individual volume controls. The volume knobs are located on the

side of the cuffs. Please keep volume to a comfortable level in order to maintain audio safety.

magnetic mounting base –model 080A131

The supplied magnet can be used for either curved or flat surfaces. To maximize frequency response, always

dab a layer of silicone grease or equivalent between the sensor and the magnet. To minimize errors in readings,

proper surface preparation should be observed. See sensor manual for further information.

cable assembly –model 050BQ006AC

The cable assembly supplied is a 6 ft coiled cable with a right-angle military connector on one end to a BNC plug

on the other. Screw the military connector onto the sensor, and make sure it is hand tight. The BNC plug is then

inserted into the BNC jack on the meter labeled sensor.

Tabla de contenidos

Otros manuales de Instrumento de medición de PCB Piezotronics

PCB Piezotronics

PCB Piezotronics 3713F11200G Manual de usuario

PCB Piezotronics

PCB Piezotronics IMI SENSORS EX607A01 Manual de usuario

PCB Piezotronics

PCB Piezotronics IMI SENSORS HT625B01 Manual de usuario

PCB Piezotronics

PCB Piezotronics EX357E93 Manual de usuario

PCB Piezotronics

PCB Piezotronics 357a100 Manual de usuario

PCB Piezotronics

PCB Piezotronics 137BPBO PLACEBO Manual de usuario

PCB Piezotronics

PCB Piezotronics IMI Sensors 625B61 Manual de usuario

PCB Piezotronics

PCB Piezotronics IMI SENSORS 66102APZ1 Manual de usuario

PCB Piezotronics

PCB Piezotronics IMI SENSORS 601A92 Manual de usuario

PCB Piezotronics

PCB Piezotronics IMI Sensors 080A131 Manual de usuario

PCB Piezotronics

PCB Piezotronics 356A70 Manual de usuario

PCB Piezotronics

PCB Piezotronics 3713B1110G Manual de usuario

PCB Piezotronics

PCB Piezotronics IMI SENSORS ICP M603C91 Manual de usuario

PCB Piezotronics

PCB Piezotronics IMI Sensors M607A11 Manual de usuario

PCB Piezotronics

PCB Piezotronics 339A31 Manual de usuario

PCB Piezotronics

PCB Piezotronics 356A14 Manual de usuario

PCB Piezotronics

PCB Piezotronics IMI SENSORS RTD602D91 Manual de usuario

PCB Piezotronics

PCB Piezotronics 3651A122KG Manual de usuario

PCB Piezotronics

PCB Piezotronics IMI SENSORS 603C61 Manual de usuario

PCB Piezotronics

PCB Piezotronics 3741B1250G Manual de usuario

PCB Piezotronics

PCB Piezotronics J357B03 Manual de usuario

PCB Piezotronics

PCB Piezotronics IMI Sensors 602D11 Manual de usuario

PCB Piezotronics

PCB Piezotronics IMI SENSORS M602D61 Manual de usuario

PCB Piezotronics

PCB Piezotronics EX357E92 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario

Acterna

Acterna MS1400 Manual de usuario