PC Partner 35C96200 Series Manual de usuario

Electronic Emission Notices

Federal Communications Commission (FCC) Statement

This equipment has been tested and found to comply with the limits for a Class B digital

device,pursuanttoPart15ofFCCRules.Theselimitsaredesignedtoprovidereasonable

protection against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with instructions contained in this manual, may cause harmful interference

to radio and television communications. However, there is no guarantee that interference

will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

- REORIENTORRELOCATETHERECEIVINGANTENNA

- INCREASETHESEPARATIONBETWEENTHEEQUIPMENTANDTHERECEIVER

- CONNECTTHEEQUIPMENTINTOANOUTLETONACIRCUITDIFFERENTFROM

THATOFTHERECEIVER

- CONSULTTHEDEALERORANEXPERIENCEDAUDIO/TELEVISIONTECHNICIAN

NOTE: Connecting this device to peripheral devices that do not comply with Class B

requirements, or using an unshielded peripheral data cable, could also result in

harmful interference to radio or television reception.

The user is cautioned that any changes or modifications not expressly approved

by the party responsible for compliance could void the user’s authority to operate

this equipment.

To ensure that the use of this product does not contribute to interference, it is

necessary to use shielded I/O cables.

copied or reproduced by any means.

While every precaution has been taken in the preparation of this manual, no responsibility

for errors or omissions is assumed. Neither is any liability assumed for damages resulting

from the use of the information contained herein.

Trademarks

All brand names, logos and registered trademarks mentioned are property of their

respective owners.

Technical Reference Booklet

Table of Contents

HARDWARE CONFIGURATION............................................................................. 3

Key Features ............................................................................................................... 3

Motherboard Layout (Model Code No. - 35C96200XX).............................................. 5

Jumper Settings ........................................................................................................... 6

CPUSpeedSelection ............................................................................................ 6

JP52, JP55 - Host Bus Speed Select.................................................................... 6

JP4- CMOS Clear.................................................................................................. 6

JP3- IOQ Depth Setting ........................................................................................ 6

JP41 - AMR Setting ............................................................................................... 6

JP7 - Ratio of Processor Core to System Bus Frequency .................................. 7

JP8 - Default Setting by Factory........................................................................... 7

Pin Assignment ..................................................................................................... 7

HARDWARE SETUP .................................................................................................. 8

ToInstallDIMMs ........................................................................................................... 8

Installing a New Processor ......................................................................................... 9

To Install a Processor to ZIF Socket ........................................................................... 9

Connect the processor Fan Connector ...................................................................... 9

Setting the Processor Speed ...................................................................................... 9

BIOS SETUP ............................................................................................................... 10

Starting Setup .............................................................................................................. 10

MainMenu.................................................................................................................... 11

Standard CMOS Features ........................................................................................... 12

Advanced BIOS Features ........................................................................................... 14

Advanced Chipset Features ....................................................................................... 14

Integrated Peripherals ................................................................................................. 14

Power Management Setup.......................................................................................... 14

PNP/PCIConfigurations................................................................................................ 14

Set Supervisor/User Password.................................................................................. 14

Flash Update Procedure ............................................................................................. 16

HARDWARE CONFIGURATION

Key Features:

Chipset

•VIA®Apollo Pro 133A (VT82C694X) Chipset.

Processor

• Full support for Intel®Celeron®, Coppermine processors use Socket 370.

• Supports bus speed of 66MHz, 100MHz and 133MHz, this includes all

Celeron®and Coppermine processors from 300MHz to 600MHz and

future processors.

VRM 8.4 (Voltage Regulator Modules) on Board

• Flexible motherboard design with on board VRM 8.4, easy to upgrade

with Future processor.

System Memory

• A total of three 168-pin DIMM sockets (3.3V Synchronous DRAM).

• Supports Synchronous DRAM at 133MHz - PC133.

• Supports error checking and correction (ECC) using parity DRAM modules.

• Supports Symmetrical and Asymmetrical DRAM addressing.

• Memory size up to 1.5G Bytes.

• Supports FP, EDO, SDRAM and VCM SDRAM memory types.

• Supports single-density DIMMs of 1MB, 2MB, 4MB, 8MB and 16MB depth (x64).

• Supports double-density DIMMs of 2MB, 4MB, 8MB, 16MB and 32MB depth

(x64).

• Supports single & double sided DIMMs.

• Banks of different DRAM types depths can be mixed.

System BIOS

• 2MB flash BIOS supporting PnP, APM, ATAPI and Windows® 95.

• Jumper selection for 5V or 12V flash memory voltage.

• Auto detects and supports LBA hard disks with capacities up to 8.4GB.

• Full support of ACPI & DMI.

• Easy to upgrade BIOS by end-user.

On-Board I/O

• On board two PCI fast IDE ports supporting up to 4 ATA, ATA2 and Ultra

DMA33/66 IDE devices.

• Supports bus master IDE, PIO mode 4 (up to 16.6M bytes/sec) and

Ultra DMA33/66 (up to 33/66M bytes/sec) transfer.

• OneECP/EPP parallel port.

• Two 16550-compatible UART serial ports.

• One floppy port, supports two FDDs of 360KB, 720KB, 1.2MB, 1.44MB

and 2.88MB capacity.

• Four USB ports.

• PS/2 mouse port.

• Infrared (IrDA) is supported.

• One Line / Speaker out, one Mic in, one Line in and MIDI / Gameport(optional).

Hardware Configuration

Technical Reference Booklet

Plug-and-Play

• Supports plug-and-play specification 1.1.

• Plug-and-play for DOS, Windows® 3.X, Windows® 95 as well as

Windows® 98.

• Fully steerable PCI interrupts.

On board AC97 Sound

•Integrated AC97 controller with standard AC97 codec.

•Direct Sound and Sound Blaster compatible.

•Full-Duplex 16-bit record and playback.

•PnP and APM 1.2 support.

Power Management

• Supports SMM, APM and ACPI.

• Break switch for instant suspend/resume on system operations.

• Energy star “Green PC” compliant .

• WOL (Wake-On-Lan) Header support.

• External Modem Ring-in Wake-up support.

Expansion Slots

•5 PCI bus master slots (Rev. 2.1 compliant).

•1 Audio Modem Riser(AMR).

• 1 ISA slot (1 ISA slot shares with 1 PCI slot).

• 1 universal AGP slot (AGP 2.0 compliant - 4X mode support).

CAUTION

Static electricity can harm delicate components of the motherboard. To prevent

damage caused by static electricity, discharge the static electricity from your

body before you touch any of the computers electronic components.

Motherboard Layout (Model Code No. - 35C96200XX)

The following diagrams show the relative positions of the jumpers, connectors, major

components and memory banks on the motherboard.

Hardware Configuration

NOTE

1) Be sure to check the cable orientation in order to match the colored strip to

the pin 1 end of the connector.

2) When you start up the system, please wait for 5 seconds after you power

on AC.

Technical Reference Booklet

Jumper Settings

This chapter explains how to configure the motherboard’s hardware. Before using your

computer, make sure all jumpers and DRAM modules are set correctly. Refer to this

chapter whenever in doubt.

CPU Speed Selection

In this motherboard, jumperless feature is implemented such that no jumper is required to

be set for different type of CPU installed.

Notice:

1. Be sure to save the CMOS setting when exit the CMOS.

2. Celeron PGA370 CPU is frequency multiplier locked, no CPU speed

change will be seen even if the frequency multiplier setting in CMOS

setup is changed.

JP52, JP55 - Host Bus Speed Select

JP52 JP55 Host Bus Speed Select

Open Open 133MHz

Open 1-2 100MHz

Close* 1-2* Auto*

JP4 - CMOS Clear

JP4 Selection

1-2* Normal*

2-3 CMOS Clear

JP3 - IOQ Depth Setting

JP3 Selection

Open* Depth of 4*

Close Depth of 1

JP41 - AMR Setting

JP41 Selection

1-2 Primary

2-3* Secondary*

JP8

JP55 1JP3

JP4

JP7

JP52

Close Open

* = Default setting.

JP41

Interinal Audio Connector

CN25:AUX-IN Pin Assignment

1 AUX-L

2 GND

3 GND

4 AUX-R

CN24:CD-IN Pin Assignment

1 CD-L

2 GND

3 GND

4 CD-R

1R G L G

G L G R

JP7 - Ratio of Processor Core to System Bus Frequency

Ratio JP7 Ratio JP7 Ratio JP7

357

3.5 5.5 7.5

4* 6 8

4.5 6.5 --

JP8 - Default Setting by Factory

Hardware Configuration

CN31:CD-IN Pin Assignment

1 CD-R

2 GND

3 CD-L

4 GND

CN32:CD-IN Pin Assignment

1 GND

2 CD-L

3 GND

4 CD-R

Pin Assignment

Close Open

* = Default setting.

CN11

FRONTRANELHEADER

HEADER 2x12

+PWR

- SW SUS+

SW -

+PWR

- LED

+HDD

- LED

+RST

- SW

SPKER

IrDA

KEYLOCK

PWR+ 1

GND 3

PWRLED+ 5

PWRLED- 7

HDDLED+ 9

HDDLED- 11

RST+ 13

GND 15

SPEAK 17

GND 21

2 SUS+

4 GND

6 IRRX

8 GND

10 IRTX

16 KEYLOCK+

20 GND

22 KEYLOCK-

24 GND

XVCC

VCC

Technical Reference Booklet

Hardware Setup

To Install DIMMs

1. Locate the DIMM sockets.

2. Holding the DIMM by the edges, remove it from its antistatic package.

3. Make sure the clips at either end of the socket are pushed away from the socket.

4. Position the DIMM above the socket. Align the two small notches in the bottom

edge of the DIMM with the keys in the socket.

5. Insert the bottom edge of the DIMM into the socket.

6. When the DIMM is seated, push down on the top edge of the DIMM until the retaining

clips at the ends of the socket snap into place. Make sure the clips are firmly in

place.

7. If you installed a DIMM with ECC memory, start the computer and use the ECC

Configuration feature in Setup to enable the use of ECC.

Turn system power off before installing and removing any

device, otherwise you’ll cause the system damage.

Clip

Clip DIMM

DIMM Socket

Notch

Hardware Setup

Installing a New Processor

An upgrade processor can dramatically increase general system speed and performance.

Most microprocessor upgrade kits include the following items:

• Microprocessor chip

• Installation instructions and technical data

Your system may have these features built in, or support them as upgrades.

To Install a Processor to ZIF Socket

To install the processor, follow these steps:

1. If the system microprocessor is already on the motherboard socket, you need to

remove it from the motherboard socket. The socket is a Zero Insertion Force (ZIF)

socketwhichhasa metal arm at one side. Carefully grasp this arm, move it horizontally

away from the socket and lift it up. Eventually you will be able to lift the chip straight

up out of the socket.

Be careful not to bend any of the pins when removing the microprocessor

chip from its socket. The microprocessor chip can be permanently damaged.

2. Unpack the new microprocessor chip.

3. Carefully align the processor with the correct orientation to the socket on the

motherboard.

4. Carefully insert the processor into the socket, and move the metal arm downward to

replace it in its original position.

Connect the Processor Fan Connector

There is a fan attached the processor to prevent the overheating. Connect the

processor fan cable to the fan connector that located on the motherboard near the

processor and ensure the fan can operate. Otherwise the CPU can overheat and

cause

damage to both CPU and motherboard.

Setting the Processor Speed

After you install the processor into the motherboard, set the processor speed by CMOS

setup.

Technical Reference Booklet

BIOSSETUP

This chapter discusses Award’s Setup Program built into the ROM BIOS. The Setup

Program allows users to modify the basic system configuration. This special information

is then stored in battery-backed RAM, which retains the setup information when the

power is turned off.

Starting Setup

The Award BIOS is immediately activated when you turn on the computer. The BIOS

reads the system information contained in the CMOS and begins the process of checking

out the system and configuring it. When it finishes, the BIOS will seek an operating

system on one of the disks and then launch and turn control over to the operating system.

While the BIOS is in control, the Setup Program can be activated:

1. By pressing <Del> immediately after switching the system on, or

2. By pressing the <Del> key when the following message appears briefly at

the bottom of the screen during the POST (Power On Self Test )

Press DEL to enter SETUP

If the message disappears before you can respond and you still wish to enter Setup,

restart the system to try again by turning it OFF then ON or pressing the “RESET” button

on the system case. You may also restart by simultaneously pressing the <Ctrl>, <Alt>,

and <Delete> keys. If you do not press the keys at the correct time and the system does

not reset, an error message will be displayed and you will again be asked to ...

PRESS F1 TO CONTINUE, DEL TO ENTER SETUP

Getting Help

Press F1 to pop up a small help window that describes the appropriate keys to use and

the possible selections for the highlighted item. To exit the Help Window press <Esc> or

the F1 key again.

In Case of Problems

If, after making and saving system changes with the Setup Program, you discover that

your computer does not reset, use the Award BIOS defaults to override the CMOS

settings.

Tabla de contenidos

Otros manuales de Placa madre de PC Partner

PC Partner

PC Partner MB520N Manual de uso y cuidado

PC Partner

PC Partner 35892900 Series Manual de uso y cuidado

PC Partner

PC Partner 35C96701 Series Manual de uso y cuidado

PC Partner

PC Partner 35880101 Manual de uso y cuidado

PC Partner

PC Partner 35880301 Manual de uso y cuidado

PC Partner

PC Partner P4X266EAS4-284E Manual de usuario

PC Partner

PC Partner BSB871S Manual de usuario

PC Partner

PC Partner 35891900 Series Manual de usuario

PC Partner

PC Partner 35891700 Series Manual de uso y cuidado

PC Partner

PC Partner 35C96801 Series Manual de uso y cuidado

PC Partner

PC Partner LXA826D Manual de usuario

PC Partner

PC Partner P4M266MS4-181M Manual de usuario

PC Partner

PC Partner SAPPHIRE PURE PERFORMANCE II Manual de usuario

PC Partner

PC Partner 35889700 Series Manual de usuario

PC Partner

PC Partner 35887201 Series Manual de usuario

PC Partner

PC Partner 35-AA33 0 Series Manual de usuario

PC Partner

PC Partner 35895100 Series Manual de uso y cuidado

PC Partner

PC Partner SAPPHIRE PURE PERFORMANCE Manual de usuario

PC Partner

PC Partner VIB814DSE Manual de usuario

PC Partner

PC Partner 35886300 Series Manual de usuario

PC Partner

PC Partner 35C92000 Series Manual de usuario

PC Partner

PC Partner P4X266AS4-258X Manual de usuario

PC Partner

PC Partner P4X266EAS4-258E Manual de usuario

PC Partner

PC Partner 357757 Series Manual de uso y cuidado

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario