Power Charge
powe r ba nk
Ty pe- C
Select Network &
Internet
Enter the most frequently used apps and functions easy via
shortcuts at the device‘s homescreen.
• Settings App (Set up Wi-Fi, Sounds, e.g.)
• Payment Application (contains all functions required for
daily payment transactions)
• Update (manual firmware or terminal soware update)
Select your Wi-Fi and enter
password
Power On/O
Power on: Press the „ “ button for 2-3 seconds to power on the
terminal.
Power o or restart the terminal: Press the „ “ until the
„Switch o; Restart“ menu is displayed. Select „Switch o“ and
your terminal switches o. Select „Restart“ and the terminal
restarts.
Magnetic Card
Swipe the card with consistent speed in the magstripe card slot
as demonstrated in the picture. While swiping, make sure that the
magstripe is facing the device.
Note: Any damage to the magstripe or incorrect
swiping may lead to transaction failures.
Contact Card
The card slot is on the right side of the device. Insert the card
(golden contacts facing up) with gentle pressure into the slot.
During the transaction process, the card should remain in the slot
as shown in the picture.
Note: If the chip contacts are damaged or oxidized, the
transaction may fail and the card needs to be replaced.
Contactless Card
The NFC field establishes at the top of the device near the printer
cover. For around 1 second, hold the contactless card close to this
zone until you hear a „beep“ sound which means a successfully
completed transaction. Aer that sound, the card can be removed.
Paper Removal
Please tear o the paper as shown in the picture. Do it quick and
with consistent power.
Homescreen
Install Paper Roll
1. Open the printer cover
2. Insert the paper roll into the paper holder. Leave a
small paper piece below the paper cutter
3. Close the printer cover
Attention: Make sure that the paper roll is
inserted correctly, otherwise it may cause a
malfunction of the printer.
Battery
1. Remove the battery cover
2. Install/disassemble battery
(ensure that contacts on the
battery match the prongs on the
inside of the device)
3. Insert/remove white socket from
battery plug
SIM Card
Your device comes with a rechargable lithium battery. Please note: for charging the device, lithium battery
must be inserted and cover must be closed.
1. Plug the USB-C end of the cable into the USB-C port on the right side of the device
2. Plug the other end into a power adaptor
3. Plug the power adaptor into a power outlet (you can also use a PC or power bank as power supply)
4. Power on the terminal
5. The terminal screen will display the charging progress
6. Aer the terminal is fully charged “ ” will display
1. Open the battery cover
2. Insert a SIM card (with contacts
face down) by carefully sliding it
into the slot until the card is fully
inserted
Attention
To install or remove SIM card, make
sure the device is turned o to
prevent damaging the card. Do not
cover the SIM card with stickers or
adhesive, this may aect the
thickness of card and hinder the
smooth insertion or removal.
Enter the devices Settings App in the apps
drawer or via shortcut at the device‘s
homescreen.
1. Select Network & Internet
2. Select Wi-Fi
3. Next, tap the slider „Use Wi-Fi“ to the right
4. Choose a wireless network from the list
5. If prompted, type the network
password
6. Select the connect button
Set up Wi-Fi
Your payment app contains all functions for daily payment transactions.
While running payment application, four categories are displayed at the
bottom of the terminal screen.
Payment App
Enter all payment funtions like
„Purchase“, „Reversal“ or
„Credit“ in the transaction
menu.
Enter the Configuration Menu
to view and print various
reports on transactions. Please
note, the customer password
(found in the Config Sheet
attached to the delivery) is
required for entering the menu.
Print out the reports by clicking
the “Print” button.
Payment Configuration
Setup
Reporting
Enter this menu to view various
reports on transactions. Please
note, customer password is
required for entering. Print
out the reports by clicking the
“Print” button.
Enter the settings menu to set
up various configurations such
as “Protect Final Balance”,
“Language”. Please note: lan-
guage settings are only applied
in the payment application,
they do not change the device’s
basic language settings.
Attention:
Please use the „Final Balance“ function of Configuration
Menu to close the current booking period and deliver all
transactions to processor. With it‘s activation, the terminal
prints out the receipt with total amounts of the booking
period. We recommend to activate „Final Balance“ at the
end of every business day.
