Patton SmartNode SN10100A Series Manual de usuario

SmartNode™ SN10100A Series

TDM+VoIP Smart Media Gateway

Quick Start Guide

Important—This is a Class A device and is not intended for use in a

residential environment.

Part Number: 07MSN10100-QS, Rev. C

Revised: August 24, 2018

Sales Office: +1 (301) 975-1000

Technical Support: +1 (301) 975-1007

E-mail: support@patton.com

www.patton.com

2SmartNode 10100A Series Quick Start Guide

• Do not open the device when the power cord is connected. For sys-

tems without a power switch and without an external power

adapter, line voltages are present within the device when the power

cord is connected.

• For devices with an external power adapter, the power adapter shall

be a listed Limited Power Source. The mains outlet that is used to

power the device shall be within 10 feet (3 meters) of the device,

shall be easily accessible, and protected by a circuit breaker in

compliance with local regulatory requirements.

• For AC powered devices, ensure that the power cable used meets

all applicable standards for the country in which it is to be

installed.

• For AC powered devices that have 3-conductor power plugs (L1, L2

& GND or Hot, Neutral & Safety/Protective Ground), the wall outlet

(or socket) must have an earth ground.

• For DC powered devices, ensure that the interconnecting cables are

rated for proper voltage, current, anticipated temperature, flamma-

bility, and mechanical serviceability.

• WAN, LAN & PSTN ports (connections) may have hazardous volt-

ages present regardless of whether the device is powered ON or

OFF. PSTN relates to interfaces such as telephone lines, FXS, FXO,

DSL, xDSL, T1, E1, ISDN, Voice, etc. These are known as “hazard-

ous network voltages” and to avoid electric shock use caution when

working near these ports. When disconnecting cables for these

ports, detach the far end connection first.

• Do not work on the device or connect or disconnect cables during

periods of lightning activity.

• This device contains no user serviceable parts. This device can only

be repaired by qualified service personnel.

• If one has reason to open the chassis or case, then the precautions

mentioned above shall be followed. This includes both the warn-

ings relating to disconnection of the input power, and the warnings

relating to the disconnection of WAN, LAN & PSTN ports.

This device is NOT intended nor approved for connection to the PSTN.

It is intended only for connection to customer premise equipment.

WARNING

SmartNode 10100A Series Quick Start Guide 3

•Gerät nicht öffnen, wenn das Netzkabel angeschlossen ist. Bei Sys-

temen ohne Netzschalter und ohne externes Netzteil liegt Netzspan-

nung im Gerät an, wenn das Netzkabel angeschlossen ist.

•Bei Geräten mit externem Netzteil muss das Netzteil die Anforderun-

gen an eine zugelassene Stromquelle mit begrenzter Leistung erfül-

len. Die Steckdose, die für die Stromversorgung des Gerätes

verwendet wird, sollte höchstens 3 Meter vom Gerät entfernt und

leicht zugänglich sein sowie durch einen den örtlichen regula-

torischen Anforderungen entsprechenden Schutzschalter abgesi-

chert sein.

•Für mit Wechselstrom betriebene Geräte muss sichergestellt sein,

dass das verwendete Netzkabel alle gültigen Normen des Landes

erfüllt, in dem es eingesetzt werden soll.

•Für mit Wechselstrom betriebene Geräte, die 3-polige Netzstecker

haben (L1, L2 u. GND oder Phase, Neutralleiter u. Schutzleiter),

muss die Steckdose geerdet sein.

•Für mit Gleichstrom betriebene Geräte muss sichergestellt sein, dass

die Verbindungskabel für Spannung, Strom, erwartete Temperatur,

Entflammbarkeit und mechanische Wartbarkeit geeignet sind.

•WAN-, LAN- u. PSTN-Ports (Anschlüsse) können unter gefährlicher

Spannung stehen, unabhängig davon, ob das Gerät ein- oder ausges-

chaltet ist. PSTN bezieht sich auf Schnittstellen wie Telefon, FXS,

FXO, DSL, xDSL, T1, E1, ISDN, Voice, usw. Diese sind als „gefährli-

che Netzwerkspannungen“ bekannt. Um einen elektrischen Schlag zu

vermeiden, muss in der Nähe dieser Anschlüsse mit Vorsicht gearbe-

itet werden. Werden Kabel von diesen Anschlüssen getrennt, zuerst

das Kabel am anderen Ende herausziehen.

•Während eines Gewitters darf nicht am Gerät gearbeitet werden und

es dürfen keine Kabel angeschlossen oder vom Netz getrennt werden.

In accordance with the requirements of council directive 2002/96/EC on

Waste of Electrical and Electronic Equipment (WEEE), ensure that at

end-of-life you separate this product from other waste and scrap and

deliver to the WEEE collection system in your country for recycling.

In Übereinstimmung mit den Anforderungen der Richtlinie 2002/96/EG

über Elektro- und Elektronik-Altgeräte (WEEE) muss sichergestellt sein,

dass Altgeräte von anderem Abfall und Schrott getrennt werden und

dem Sammel- und Verwertungssystem für Elektro- und Elektronik-Alt-

geräte in Ihrem Land zum Recycling zugeführt werden.

WARNING

4SmartNode 10100A Series Quick Start Guide

1.0 Before you begin

In the box, you will find:

•One SmartNode SN10100A

•One set of mounting brackets with screws

•One DB-9 to RJ-45 adapter

•Three CAT5 Ethernet straight cables (male-male), three meters in length

•One warranty sheet

•One packing slip

•One SmartNode SN10100A Series Quick Start Guide

•One SmartNode SN10100A Important Notice sheet with unique information for your

specific unit

2.0 Installing the rack hardware

1. Install rack-mounting hardware on to the SN10100A and install the unit on the

equipment rack.

2. Connect the Ethernet port to your management network.

Figure 1. Installing the SN10100A

3.0 Connecting to the VoIP Network

1. Connect the VoIP Ports 0/1 and 0/1 to your network (see figure 2).

SmartNode 10100A Series Quick Start Guide 5

Note Ethernet ports (ETH 0/0 & 0/1), and SMS ports (SMS-0/0 & 0/1) are not used

when connecting VoIP.

Figure 2. Connecting the VoIP ports

4.0 Connecting to the PSTN

A SN10100A with 8 RJ48C type ports enables the connection to T1/E1 lines.

Note T1/E1 ports are activated by software license; the number of active ports

depends on the licenses purchased.

1. Start with port 0, located at the top and leftmost position. Connect one cable

between this port and the T1/E1 line.

2. Repeat step 1, using the next available port

Figure 3. Port Interface to the PSTN

5.0 Grounding the Equipment Chassis

As a standard safety practice, the chassis of the SN10100A series gateway must be

properly grounded to protect against any contact with an electrical fault condition. It is

recommended that the chassis be connected to an earth ground. If the SN10100A

series gateway is mounted in an equipment rack, then the ground cable must be con-

nected from the ground lug of the SN10100A series gateway ground to the ground bar

of the equipment rack. If more than one SN10100A series gateway is installed in an

equipment rack, each SN10100A series gateway must be grounded directly to the

equipment rack ground bar.

VoIP Network 1

1514

1312

10 11

89320

7654

MGMT0

MGMT1

ETH0

ETH1

VOIP0

VOIP1

VoIP Network 2

1514

1312

10 11

89320

7654

MGMT0

MGMT1

ETH0

ETH1

VOIP0

VOIP1

16-Port Interface to the PSTN

6SmartNode 10100A Series Quick Start Guide

5.1 Guidelines

•Use 10 AWG (minimum) stranded ground wire.

•Terminate equipment side of ground wire with a #10 ring terminal.

•Do NOT daisy chain the ground between equipment. Use a ground bus bar, as

shown in figure 4.

Figure 4. Chassis ground connection

•Do not over-tighten ground lug connections.

•Keep the length of the ground wire as short as possible.

5.2 Grounding procedure

Do the following to connect to the SN10100A series gateway to ground:

1. Connect one end of a ground wire to the ground lug of the SN10100 series gate-

way. See figure 4.

2. Connect the other end of the ground wire to a ground bar of the equipment rack.If

the SN10100 series gateway is not installed in an equipment rack, then connect

the ground wire to the main water entry pipe.

3. Verify that the resistance of the ground path is less than 0.5 ohms.

To avoid the risk of fire, electric shock, or personal injury do not apply

power to the SN10100A before the equipment chassis ground has been

installed.

WARNING

Ground Bar

1514

1312

10 11

89320

7654

MGMT0

MGMT1

ETH0

ETH1

VOIP0

VOIP1

1514

1312

10 11

89320

7654

MGMT0

MGMT1

ETH0

ETH1

VOIP0

VOIP1

1514

1312

10 11

89320

7654

MGMT0

MGMT1

ETH0

ETH1

VOIP0

VOIP1

Earth

Ground

SmartNode 10100A Series Quick Start Guide 7

6.0 Connecting to the power source

1. Connect AC power cables between the AC connectors of the SN10100A and the

two independent power sources (see figure 5).

2. Verify that the Power LED on the front panel (see figure 6) is a solid green.

Figure 5. Connecting the power source

Figure 6. Power LED location

7.0 Connecting to the Control host

1. Connect to the Control host through the console serial port (see 7.1 “Connecting

the console serial port” on page 8) OR the Ethernet management interface (see

7.2 “Connecting the Ethernet management interface” on page 8).

The IP address of the management port is 192.168.200.10/24. If it is not possible

to connect to the management port via IP, use the serial cable to connect to the

SmartNode Control host for the first time.

2. Default HOSTNAME is the Control host serial number, which can be found in the

“Important Notice” sheet included with your shipment.

3. Refer to the "Important Notice" sheet for the username and password to log onto

the SmartMedia WebPortal. Navigate to: HTTP://HOSTNAME:12358, to configure

the SmartNode unit. (username/password: root/root)

Power

Source 1

Power

Source 2

1514

1312

10 11

89320

7654

MGMT0

MGMT1

ETH0

ETH1

VOIP0

VOIP1

PowerLED

8SmartNode 10100A Series Quick Start Guide

7.1 Connecting the console serial port

1. Connect a CAT5 RJ-45 (male-male) cable (supplied with unit) between the COM

port of your computer and the serial port (labeled CONSOLE) of the SN10100A.

2. If your computer’s serial port features a DB9 connector, use the DB9 to RJ-45

adapter supplied with your SN10100A. If your computer's serial port features a

USB connector, you will need to provide a USB to DB9 adapter.

Figure 7. Connecting the console serial port

7.2 Connecting the Ethernet management interface

1. Connect the supplied CAT5 Ethernet cable to the management port labeled

MGMT0 on the rear of the SmartNode 10100A (see figure 8 on page 8.

2. Log into the SmartNode using the specific credentials included on the “Important

Notice” sheet that shipped with your unit. The management port is configured

with a static Class C IP address by default

Figure 8. Connecting the management interface

Serial Terminal (PC)

Note A PattonModel 16F-561 RJ45 to DB-9 adapteris

included with each SmartNode 10200A device.

CONSOLE Port

1514

1312

10 11

89320

7654

MGMT0

MGMT1

ETH0

ETH1

VOIP0

VOIP1

Ethernet Management

Port (MGMT0)

SmartNode 10100A Series Quick Start Guide 9

8.0 Configuring the SmartNode

You may access the SmartNode through the console management port, or through the

Ethernet management port. Refer to the following sections for more information:

•8.1 “Accessing the SmartNode via the Console Management port” on page 9

•8.2 “Accessing the SmartNode via the Ethernet Management port” on page 9

8.1 Accessing the SmartNode via the Console Management port

Logging into the SmartNode Console

1. To physically connect the console serial port, follow the instructions in 7.1 “Con-

necting the console serial port” on page 8.

2. To communicate with the SN10100A through the console port, you must first

configure a terminal emulator or console application (such as HyperTerminal or

Putty) in order to configure initial settings. Configure the terminal emulator with

the following settings:

3. Log into the console using the specific credentials included on the 'Important

Notice' that shipped with your unit. (If you do not have the “Important Notice”

sheet, contact support@patton.com).

8.2 Accessing the SmartNode via the Ethernet Management port

Logging into the SmartNode via SSH

1. To physically connect the Ethernet management port, follow the instructions in

7.2 “Connecting the Ethernet management interface” on page 8.

2. To access the SN10100A, you must use an SSH connection. The password is set

at the factory and is indicated on the “Important Notice” sheet included with your

unit. (If you do not have the “Important Notice” sheet, contact support@pat-

ton.com).

3. The factory default configuration for the Management Ethernet Interface is a

Static IP address of 192.168.200.10/24.

Preparing for Web Management

After logging into the SN10100A via the console port or SSH, a control menu displays.

This menu allows you to complete simple tasks like setting the time zone and configur-

ing the management IP Address, and more complicated tasks like advanced debugging.

Baud rate Data rate Parity Stop bits Flow control

9600 8 bits None 1None

10 SmartNode 10100A Series Quick Start Guide

For debugging assistance, contact Patton’s Support team at supp[email protected].

Once your IP Address and Time Zone are set, there are no more configuration steps in

the CLI and you may proceed to the web management page.

9.0 Logging into the Web Interface

This section describes how to login and navigate the SmartNode 10100A Web Portal.

The first step involved in initially configuring any Smart Media system involves logging

on to the Web Portal. This can be divided into two distinct tasks: connecting to the

10100A via IP and logging on to the Web Portal. For establishing IP connectivity refer

to 8.2 “Accessing the SmartNode via the Ethernet Management port” on page 9.

9.1 Connecting to the web server

Using a web browser, connect to the Web Portal by typing the following in your address

bar:

–http://[DEVICE HOST NAME]:12358

or, alternately,

–http://[DEVICE IP ADDRESS]:12358

9.2 Logging on to the Web Portal

In order to log on to the Web Portal configuration tool, enter the root user ID and pass-

word. The default values for these parameters are:

–User ID: root

–Default password: root

10.0 Additional Information

Refer to the following manuals–available online at www.patton.com/manuals–for

detailed information about installing, configuring, and operating the SN10100A models,

along with warranty, trademark, and compliance information.

•SmartNode 10100A Series User Manual –www.patton.com/manuals/SN10100.pdf

•Smart Media System Software Configuration Guide –www.patton.com/manuals/

SmartMedia-scg.pdf

A.0 Compliance Information

A.1 Compliance

EMC:

Tabla de contenidos

Otros manuales de Puerta de Patton

Patton

Patton SmartNode 5541 Series Manual de usuario

Patton

Patton SmartNode 4900 Manual de usuario

Patton

Patton SmartNode 4520 Series Manual de usuario

Patton

Patton Smart Node 4120 Manual de usuario

Patton

Patton SmartNode 4970 Series Manual de usuario

Patton

Patton SmartNode SN10200A Series Instrucciones de funcionamiento y mantenimiento

Patton

Patton SN4112 Manual de usuario

Patton

Patton SmartNode 4131 Manual de usuario

Patton

Patton 1000 Manual de usuario

Patton

Patton SmartNode 10100 Series Manual de usuario

Patton

Patton SmartNode 4970 Series Manual de usuario

Patton

Patton SmartNode 5540 Series Manual de usuario

Patton

Patton SmartNode 10200 Series Manual de usuario

Patton

Patton SmartNode 4970A Series Manual de usuario

Patton

Patton SmartNode 4554 Manual de usuario

Patton

Patton SmartNode 4830 DSL Series Manual de usuario

Patton

Patton SmartNode 4740 Series Manual de usuario

Patton

Patton SmartNode 4554 Manual de usuario

Patton

Patton SmartNode SN5550 Manual de usuario

Patton

Patton SmartNode 4110 Series Manual de usuario

Patton

Patton 07MSNOGA-DS5 Manual de usuario

Patton

Patton SmartNode 5540E Series Manual de usuario

Patton

Patton FiberPlex FPX6000 Series Manual de usuario

Patton

Patton FiberPlex FPX6000 Series Manual de usuario

Manuales populares de Puerta de otras marcas

LST

LST M500RFE-AS Manual de usuario

Kinnex

Kinnex Media Gateway Manual de usuario

2N Telekomunikace

2N Telekomunikace 2N StarGate Manual de usuario

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manual de usuario

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manual de usuario

Telsey

Telsey CPVA 500 - SIP Manual de usuario

RTA

RTA 460A-NNA4 Hoja de especificaciones

Shaw

Shaw Gateway HDPVR Manual de usuario

ABB

ABB VSN900 Guía de inicio rápido

Commander

Commander Pulse Manual de usuario

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manual de usuario

NETGEAR

NETGEAR C6300BD Manual de usuario

Amit

Amit CDW531AM Manual de usuario

HMS

HMS Netbiter EasyConnect EC150 Manual de usuario

Huawei

Huawei EchoLife HG620 Manual de usuario

AT&T

AT&T U-verse 3801 Manual de uso y cuidado

Logic IO

Logic IO RTCU MX2 turbo Manual de usuario

Suttle

Suttle MediaMAX MXM-521 Manual de usuario