Patton electronics 1092RC Manual de usuario

USER

MANUAL

MODEL 1092RC

High Speed, 2-Wire,

Synchronous and

Asynchronous

Rack Mount Modem Card

SALES OFFICE

(301) 975-1000

TECHNICAL SUPPORT

(301) 975-1007

http://www.patton.com

Part# 07M1092RC-E

Doc# 033021U,

Rev. F

Revised 1/22/08

CERTIFIED

An ISO-9001

Certified Company

Dear Valued Customer,

Thank you for purchasing Patton Electronics products! We do appreciate

your business. I trust that you find this user manual helpful.

We manufacture one of the widest selections of data communications

products in the world including CSU/DSU's, network termination units,

powered and self-powered short range modems, fiber optic modems, interface

converters, baluns, electronic data switches, data-line surge protectors,

multiplexers, transceivers, hubs, print servers and much more. We produce

these products at our Gaithersburg, MD, USA, facility, and can custom

manufacture products for your unique needs.

We would like to hear from you. Please contact us in any of the following

ways to tell us how you like this product and how we can meet your product

needs today and in the future.

Web: http://www.patton.com

Sales E-mail: [email protected]

Support E-mail: [email protected]

Phone - Sales (301) 975-1000

Phone - Support (301) 975-1007

Fax: (301) 869-9293

Mail: Patton Electronics Company

7622 Rickenbacker Drive

Gaithersburg, MD 20879 USA

We are committed to a quality product at a quality price. Patton

Electronics is ISO 9001 certified. We meet and exceed the highest standards

in the industry (CE, UL, etc.).

It is our business to serve you. If you are not completely satisfied with this

product or service provided by Patton Electronics or its distributors, please let

us know.

Thank you.

Burton A.Patton

Vice President

P.S. Please tell us where you purchased this product.

_________________________________________________________

TABLE OF CONTENTS

Section Page

1.0 Warranty Information .............................................................2

1.1 Radio and TV Interference

1.2 CE Notice

1.3 Service Information

2.0 General Information...............................................................4

2.1 Features

2.2 Description

3.0 Configuration .........................................................................5

3.1 Configuring the Hardware Switches

3.1.1 Reversible Interface Driver Board

3.1.2 Configuration Switch Set “S1”

3.1.3 Configuration Switch Set “S2”

3.2 Configuring the Software Switches

3.2.1 Configuring the Local 1092RC

3.2.2 Configuring the Remote 1092RC

3.3 Configuring the Rear Interface Card

3.3.1 Model 1000RCM12592 Strap Settings

3.3.2 Model 1000RCM13492 Strap Settings

4.0 Installation ...........................................................................24

4.1 The Model 1000R16P Rack Chassis

4.1.1 The Rack Power Supply

4.2 Installing the Model 1092RC Series Into Chassis

4.3.1 Connecting to a “DTE” Device

4.3.2 Connecting to a “DCE” Device

4.3.3 Connecting the Twisted Pair Interface

4.3 Wiring the Model 1092RC Series

5.0 Operation.............................................................................28

5.1 LED Status Indicators

5.2 Test Modes

5.2.1 using Local Line Loopback (LLB)

5.2.2 Using Remote Digital Loopback (RDL)

5.2.3 Using the V.52 (BER Test Pattern Generator

Appendix A - Specifications ........................................................32

Appendix B - Factory Replacement Parts and Accessories .......33

Appendix C - Terminal Interface Pin Assignments......................34

Appendix D - Control Port Pin Assignments ...............................36

Appendix E - Line Interface Pin Assignments.............................37

APPENDIX D

PATTON MODEL 1092RC

CONTROL PORT PIN ASSIGNMENT

(RJ-45 CONNECTOR ON 1000CC CARD)

Pin Function RJ-45 Pin Number

Transmit data (from DTE)................................7

Receive date (to DTE).....................................6

Ground.............................................................5

1.0 WARRANTY INFORMATION

Patton Electronics warrants all Model 1092RC components to be

free from defects, and will—at our option—repair or replace the product

should it fail within one year from the first date of shipment.

This warranty is limited to defects in workmanship or materials, and

does not cover customer damage, abuse or unauthorized modification.

If this product fails or does not perform as warranted, your sole

recourse shall be repair or replacement as described above. Under no

condition shall Patton Electronics be liable for any damages incurred

by the use of this product. These damages include, but are not limited

to, the following: lost profits, lost savings and incidental or

consequential damages arising from the use of or inability to use this

product. Patton Electronics specifically disclaims all other warranties,

expressed or implied, and the installation or use of this product shall be

deemed an acceptance of these terms by the user.

1.1 RADIO AND TV INTERFERENCE

The Model 1092RC generates and uses radio frequency energy,

and if not installed and used properly—that is, in strict accordance with

the manufacturer's instructions—may cause interference to radio and

television reception. The Model 1092RC has been tested and found to

comply with the limits for a Class A computing device in accordance

with the specifications in Subpart J of Part 15 of FCC rules, which are

designed to provide reasonable protection from such interference in a

commercial installation. However, there is no guarantee that

interference will not occur in a particular installation. If the Model

1092RC does cause interference to radio or television reception, which

can be determined by disconnecting the unit, the user is encouraged to

try to correct the interference by one or more of the following measures:

moving the computing equipment away from the receiver, re-orienting

the receiving antenna and/or plugging the receiving equipment into a

different AC outlet (such that the computing equipment and receiver are

on different branches). In the event the user detects intermittent or

continuous product malfunction due to nearby high power transmitting

radio frequency equipment, the user is strongly advised to take the

following steps: use only data cables with an external outer shield

bonded to a metal or metalized connector; and, configure the rear card

as shown in section 3.3 of this manual.

1.2 CE NOTICE

The CE symbol on your Patton Electronics equipment indicates

that it is in compliance with the Electromagnetic Compatibility (EMC)

directive and the Low Voltage Directive (LVD) of the European Union.

A Certificate of Compliance is available by contacting Technical

Support.

APPENDIX C (Continued)

PATTON MODEL 1092RC

TERMINAL INTERFACE PIN ASSIGNMENT

DB-25F Connector-DCE

(RS-232 Interface)

Pin # Signal

1...........................FG (Frame Ground)

2.......................... TD (Transmit Data)

3...........................RD (Receive Data)

4...........................RTS (Request to Send)

5...........................CTS (Clear to Send)

6...........................DSR (Data Transfer Rate)

7...........................SGND (Signal Ground)

15.........................TC (Test Control-A)

17.........................RC (Receive Timing)

18.........................LLB (Local Line Loop)

20.........................DTR (Data Transfer Rate)

21.........................RDL (Remote Digital Loop)

24.........................XTC (External Transmit Clock

25.........................TM (Test Mode)

1.3 SERVICE

All warranty and nonwarranty repairs must be returned freight

prepaid and insured to Patton Electronics. All returns must have a

Return Materials Authorization number on the outside of the shipping

container. This number may be obtained from Patton Electronics

Technical Support:

tel: (301) 975-1007;

email: [email protected].

www: http://www.patton.com.

NOTE: Packages received without an RMA number will not be

accepted.

Patton Electronics' technical staff is also available to answer any

questions that might arise concerning the installation or use of your

Model 1092RC. Technical Service hours: 8AM to 5PM EST, Monday

through Friday.

APPENDIX C

MODEL 1092RC TERMINAL INTERFACE PIN ASSIGNMENT

M/34F Connector-DCE

(V.35 Interface)

Pin # Signal

B ...........................SGND (Signal Ground)

C ...........................RTS (Request to Send)

D ...........................CTS (Clear to Send)

E ...........................DSR (Data Set Ready)

F............................CD (Carrier Detect)

H ...........................DTR (Data Transfer Ready)

L....................................LLB (Local Line Loop)

M ...........................TM (Test Mode)

N ...........................RDL (Remote Digital Loop)

P ...........................TD(Transmit Data)

R ...........................RD (Receive Data)

S ...........................TD/ (Transmit Data-B)

T............................RD/ (Receive Data-B)

U ...........................XTC (External Transmit Clock)

V ...........................RC(Receive Timing)

W ...........................XTC/ (External Transmit Clock)

X ...........................RC/ (Receive Timing)

Y ...........................TC(Test Control-A)

AA ..........................TC/ (Test Control-B)

2.0 GENERAL INFORMATION

Thank you for your purchase of this Patton Electronics product.

This product has been thoroughly inspected and tested and is

warranted for One Year parts and labor. If any questions arise during

installation or use of this product, please contact Patton Electronics

Technical Support at: (301) 975-1007.

2.1 FEATURES

• Synchronous data rates: 9.6, 19.2, 32, 56, 64 and 128 kbps in all

clock modes

• Asynchronous data rates: 0 - 38.4 kbps

• Full duplex operation over a one or two twisted pair (2- or 4-Wires)

• Point-to-point distances up to 5 miles (8Km)

• Remote digital loopback, local line loopback diagnostics

• Internal, external or receive recovered clocking options

• LED indicators for TD, RD, CTS, CD, DTR, TM, ER and NS

• Fits in Patton’s rack chassis and cluster boxes

• Made in the U.S.A.

2.2 DESCRIPTION

The Patton Model 1092RC

KiloModem 2W

TM baseband modem

allows synchronous or asynchronous data to be transmitted up to 5

miles (8 km) over one or two twisted pair (2 or 4 Wire). Supporting

synchronous speeds up to 128 kbps and asynchronous speeds up to

38.4 kbps, the 1092RC is perfect for LAN interconnection or high speed

internet links.

Supporting 2B1Q encoding, Automatic Equalization and Auto Gain

Control, the Model 1092RC compensates for poor line quality.

Swappable interface driver boards and interface cards allow the user to

easily change applications between RS-232 and V.35. Future driver

boards and interface cards will include X.21, G.703, and RS-530. The

Model 1092RC also features convenient front panel diagnostic switches

and LEDs that allow for easy setup, configuration and testing.

The Model 1092RC is designed to fit into Patton’s 2U (3.5”) high

rack chassis. This 16-card chassis has a switchable 120/240 VAC

power supply (optional 48 VDC) and mounts cards in a mid-plane

architecture: The front card can be plugged into different rear cards.

APPENDIX B

PATTON MODEL 1092RC

FACTORY REPLACEMENT PARTS

AND ACCESSORIES

Patton Model # Description

1000RCM12592.........Rear card w/DB25F & RJ45 (V.24 interface)

1000RCM12492.........Rear card w/ M/34F & RJ45 (V.35 interface)

1000RPEM ................120/240V Rear Power Entry Module

1000RPSM-2 .............120/240V Front Power Supply Module

1000RPEM-DC..........DC Rear Power Entry Module

1000RPSM-48A.........48V Front Power Supply Module

1000RPEM-V.............120/240V CE Compliant Rear Power

Entry Module

1000RPEM-V.............120/240V CE Compliant Rear Power

Supply Entry Module

1000CC......................Control Card

IM1RC/A ....................Interface daughter card, V24/V.35

0805US......................American Power Cord

0805EUR ...................European Power Cord CEE 7

0805UK......................United Kingdom Power Cord

0805AUS ...................Australia/New Zealand Power Cord

0805DEN ...................Denmark Power Cord

0805FR......................France/Belgium Power Cord

0805IN .......................India Power Cord

0805IS .......................Israel Power Cord

0805JAP ....................Japan Power Cord

0805SW.....................Switzerland Power Cord

3.0 CONFIGURATION

This section describes the location and orientation of the Model

1092RC’s configuration switches and jumpers, and provides detailed

instructions for all possible settings.

3.1 CONFIGURING THE HARDWARE SWITCHES

The Model 1092RC Series front card defaults to the use of

hardware switches for configuration. There is an interface driver board

strap, and two eight-position DIP switches, on the front card (see

Figure 1, below).

Figure 2 shows the orientation of the DIP switches with respect to

the “ON” and “OFF” positions.

12345678

Figure 1. Model 1092RC, showing configuration switches and interface board

SW1

SW2

Interface

Driver

Board

THIS SIDE UP FOR V.35

FRONT

Figure 2. Close up of configuration switches (both sets are identical in appearance)

NOTE: The ON position is oriented toward the front of the Model 1092RC.

12345678

OFF

Front Panel

ON OFF

APPENDIX A

PATTON MODEL 1092RC SPECIFICATIONS

Transmission

Format: Synchronous or asynchronous

Transmission Line: Single unconditioned twisted pair

Clocking: Internal, external or receive recover

Distance: Up to 10.8 miles (17.3Km), all data rates, 19

AWG (.9mm)

Up to 7.2 miles (11.5Km), all data rates, 22

AWG (.6mm)

Up to 5 miles (8Km), all data rates, 24AWG

(.55mm)

Up to 3.41 miles (5.45Km), all data rates, 26

AWG(.4mm)

Data Rates:

Sync

32, 56, 64 & 128 kbps;

Async

0 - 38.4 kbps

Diagnostics: V.52 compliant bit error rate pattern

(511/511E pattern) generator and detector

with error injection mode; Local Line

Loopback and Remote Digital Loopback,

activated by front panel switch or via serial

interface

LED Indicators: TD, RD, CTS, CD, DTR, NS(no signal),

ER (error) and TM (test mode)

Connectors: RJ-45 on line side; DB-25 female or M/34

female on serial interface side, depending

upon which interface rear card is installed.

Temperature: 32-140°F (0-60°C)

Altitude: 0-15,000 feet (0-4572 meters)

Humidity: 5 to 95% noncondensing

Dimensions: Front Card: 4.81” x 3.10” x 0.95”

(12.2 x 7.8 x 2.4cm)

Rear Card: 3.33” x 2.8” x 0.95”

(8.4 x 7.1 x 2.4cm)

Weight: Front Card: 0.22 lbs (.10Kg)

Rear Card (M/34 with V.35 interface): 0.16

lbs (.07Kg)

Rear Card (DB-25/RS-232 interface): 0.12

lbs. (.05Kg)

3.1.1 Reversible Interface Driver Board

The Model 1092RC Series features switchable interface driver

boards that allow a wide range of DTE interface connections. Each

interface driver board incorporates two interfaces -- one on each side

of the driver board. Figure 3 shows the Interface Driver Board on the

bottom of the 1092RC PC board.

Follow the instructions below to select the correct interface for your

application:

1. With the 1092RC pulled out of the rack or clusterbox chassis,

locate the driver board on the top of the 1092RC front card.

2. Lift the interface board gently off of the PC board.

3. Locate the correct interface on the bottom of the driver board.

For example, the RS-232/V.35 interface board is marked

“THIS SIDE UP FOR RS-232” on one side and “THIS SIDE

UP FOR V.35” on the other side .

4. Re-orient the interface board into the socket with the

appropriate interface pointed UP and with the arrow pointing

toward the front panel of the Model 1092RC PC board.

5. Push the Interface Driver Board gently onto the socket and re-

install into the rack or cluster system.

Figure 3. Closeup of Model 1092RC Interface Driver Board

12345678

Interface

Driver

Board

FRONT THIS SIDE UP FOR V.35

5.2.3 Using the V.52 (BER) Test Pattern Generator

To use the V.52 BER tests in conjunction with the Remote Digital

Loopback tests* (or with Local Line Loopback tests), follow these

instructions:

1. Locate the “511/511E” toggle switch on the front panel of the

1092RC and move it to the left. This activates the V.52 BER

test mode and transmits a “511” test pattern into the loop. If

any errors are present, the local modem’s red “ER” LED will

blink sporadically.

2. If the above test indicates no errors are present, move the

V.52 toggle switch to the right, activating the “511/E” test with

errors present. If the test is working properly, the local

modem's red “ER” LED will glow. A successful “511/E” test

will confirm that the link is in place, and that the Model

1092RC’s built-in “511” generator and detector are working

properly.

*NOTE: The above V.52 BER tests can be used independently of

the Remote Digital Loopback tests. This requires two operators:

one to initiate and monitor the tests at the local Model 1092RC,

and one to do the same at the remote Model 1092RC. In this

case, the test pattern sent by each Model 1092RC will not be

looped back, but will be transmitted down the line to the other

Model 1092RC.

3.1.2 Configuration DIP Switch Set “S1”

The configuration switches on S1 allow you to specify the data

rate, async/sync data format, transmit clock source and response to

RDL request. Default settings of S1 are shown in the table below.

Switches S1-1 and S1-2: Data Rate

Use Switches S1-1and S1-2 to configure the data rate of the Model

1092RC. Each setting represents one synchronous data rate and one

asynchronous data rate.

S1-1 S1-2 Sync Data Rate Async Data Rate

On On 32 Kbps Reserved

Off On 56 Kbps Reserved

On Off 64 Kbps Reserved

Off Off 19.2 or 128 Kbps* 0 - 38.4 kbps

*NOTE: Model 1092RC operates either at a synchronous rate of

19.2 kbps

128 kbps depending on the orientation of Switch S2.

To operate synchronously at 19.2 kbps, set Switch S2-1 ON. To

operate at 128 kbps, set Switch S2-1 OFF. See Section 3.1.3 for

more information.

Position Function Factory Default

S1-1 Data Rate On

S1-2 Data Rate Off

S1-3 DSR during Local Line Loop On

S1-4 Async/Sync Data Format Off

S1-5 Async/Sync Data Format Off

S1-6 Tx Clock Source On

S1-7 Tx Clock Source On

S1 SUMMARY TABLE

64K Sync

}

Async/Sync

Internal Clock

}

DSR Enable

NOTE: Switch S1-8 must be in the “ON” position).

2. Verify that the data terminal equipment is operating properly

and can be used for a test.

3. Perform a V.52 BER (bit error rate) test as described in

Section 5.2.3. If the BER test equipment indicates no faults,

but the data terminal indicates a fault, follow the

manufacturer’s checkout procedures for the data terminal.

Also, check the interface cable between the terminal and the

Model 1092RC.

5.2.2 Using Remote Digital Loopback (RDL)

The Remote Digital Loopback (RDL) test checks the performance

of both the local and remote Model 1092RCs, and the communication

link between them. Any characters sent to the remote Model 1092RC

in this test mode will be returned back to the originating device (see

Figure 12, below). For example, characters typed on the keyboard of

the local terminal will appear on the local terminal screen after having

been passed to the remote Model 1092RC and looped back.

To perform an RDL test, follow these steps:

1. Activate RDL. This may be done in two ways: first, by moving

the front panel toggle switch to the Left to “Remote”. Second,

by raising the RDL signal on the interface (see Appendix C).

NOTE: Switch S1-8 must be in the “ON” position.

2. Perform a V.52 BER test as described in Section 5.2.3. If the

BER test equipment indicates a fault, and the Local Line

Loopback test was successful for both Model 1092RCs, you

may have a problem with the twisted pair line between the

modems. You should then check the twisted pair line for

proper connections and continuity.

Figure 12. Remote Digital Loop

Local 1092RC Remote 1092RC

Switch S1-3: Data Set Ready During Local Line Loopback Test

Use Switch S1-3 to control the behavior of the DSR signal at the

EIA interface during the local line loopback test.

S1-3 Setting Description

On Enabled DSR is on during local

line loop (default)

Off Disabled DSR is off during local

line loop

Switches S1-4 and S1-5: Async/Sync Operation

Use Switches S1-4 and S1-5 to configure the Model 1092 for

async/sync operation. Both switches must be set in the “Off” position.

There is no other valid setting.

S1-4 S1-5 Setting

Off Off Allows sync/async control

On Off Reserved

Off On Reserved

On On Reserved

Switches S1-6 and S1-7: Transmit Clock Source

Use Switches S1-6 and S1-7 to configure the 1092 for internal,

external, or receive recover clock mode.

S1-6 S1-7 Setting Description

On On Internal Transmit Clock

derived internally

Off On External Transmit Clock

derived from the

terminal interface

On Off Receive Recover Transmit clock derived

from the received line

signal

Off Off hardware reset

Important:

A pair of Model 1092s communicate synchronously

across the twisted pair line connection. Therefore, you must set

these switches whether your application is async or sync.

For X.21 or Async applications, please configure one Model 1092

for internal clock mode and the other Model 1092 for receive

recover clock mode.

ER glows red to indicate the likelihood of a Bit Error

in the received signal. During the 511 or 511/E

test, ER flashes to indicate that the Test Pattern

Detector has detected a bit error.

TM glows red to indicate that the Model 1092RC

has been placed in Test Mode. The unit can be

placed in test mode by the local user or by the

remote user.

NS (No Signal) glows red to indicate that the local

Model 1092RC has not yet connected with the

remote Model 1092RC.

5.2 TEST MODES

The Model 1092RC offers two proprietary loopback test modes,

plus a built-in V.52 BER test pattern generator, to evaluate the condition

of the modems and the communication link. These tests can be

activated physically from the front panel, or via the interface.

5.2.1 Using Local Line Loopback (LLB)

The Local Line Loopback (LLB) test checks the operation of the

local Model 1092RC, and is performed separately on each unit. Any

data sent to the local Model 1092RC in this test mode will be echoed

(returned) back to the user device (see Figure 11, below). For

example, characters typed on the keyboard of a terminal will appear on

the terminal screen.

To perform an LLB test, follow these steps:

1. Activate LLB. This may be done in one of two ways: First, by

moving the front panel toggle switch to the right to “Local”.

Second, by raising the LLB signal on the interface (see

Appendix C). Once LLB is activated, the Model 1092RC

transmitter output is connected to its own receiver. The “TM”

LED should be lit.

1090

Figure 11 Local Line Loopback

1092RC

Switch S1-8: Respond to Local and Remote Loop from DTE

Use Switch S1-8 to determine whether the DTE can initiate a local

or remote loopback test. When Switch S1-8 is in the On position, the

DTE may activate a local or remote loopback test by raising the

appropriate interface signal (see Appendix C to determine the local and

remote loopback signals).

S1-8 Setting

On Respond to loop request from DTE Interface

Off Do not respond to loop request from DTE Interface

3.1.3 DIP Switch Set “S2” - Control Port Address and 19.2 kbps

Sync.

The Model 1092RC may be configured by a menu-driven software

system when used with the Patton Model 1000CC (for ordering

information, see Appendix B). In order to configure the Model 1092RC

by software commands, you must set its control port address.

The control port address is defined by a two digit decimal number.

Switches S2-1 through S2-4 define the least significant digit or the

“ones” digit, and Switches S2-5 through S2-7 define the “tens” digit.

Valid addresses are 0 through 79. Use the table below and the

instructions that follow the table to set the the control port to the desired

address.

S2 SUMMARY TABLE

Switch S2 Settings

1*2 345678

Address

Digit

0ONONONON

ON ON ON ON

OFF ON ON ON

2 ON OFF ON ON ON OFF ON ON

3 OFF OFF ON ON OFF OFF ON ON

4 ON ON OFF ON ON ON OFF ON

5 OFF ON OFF ON OFF ON OFF ON

6 ON OFF OFF ON ON OFF OFF ON

7 OFF OFF OFF ON OFF OFF OFF ON

8 ON ON ON ON N/A N/A N/A ON

NOTE: Default Settings Shown in Bold Italics; Default Address is “10”

5.0 OPERATION

Once the Model 1092RC is properly configured and installed, it

should operate transparently. This sections describes functions of the

LED status indicators, and the use of the built-in loopback test modes.

5.1 LED STATUS INDICATORS

The Model 1092RC features twelve front panel LEDs that monitor

power, the DTE signals, network connection and test modes. Figure 10

(below) shows the front panel location of each LED. Following Figure

10 is a description of each LEDs function.

TD & RD glow red to indicate an idle condition of Binary

“1” data on the respective terminal interface

signals. Green indicates Binary “0” data.

CTS consists of 2 LEDs, 1 red, 1 green. CTS glows

green to indicate that the Clear to Send signal from

the modem is active. Red indicates inactive CTS.

CD consists of 2 LEDs, 1 red, 1 green. CD glows

red if no carrier signal is being received from the

remote modem. Green indicates that the remote

modem’s carrier is being received.

DTR glows green to indicate that the Data Terminal

Ready signal from the terminal is active.

Figure 10. The Model 1092RC Series' front panel LEDs

Model 1092RC

CTS

LLB

511

RDL

511ER

DTR

Tabla de contenidos

Otros manuales de Tarjeta de red de Patton electronics

Patton electronics

Patton electronics 1080ARC Manual de usuario

Patton electronics

Patton electronics IM2RC/F Manual de usuario

Patton electronics

Patton electronics 1186RC Manual de usuario

Patton electronics

Patton electronics 1205RC Manual de usuario

Patton electronics

Patton electronics NetLink 1094ARC Manual de usuario

Patton electronics

Patton electronics 1193RC Manual de usuario

Patton electronics

Patton electronics 1018RC Manual de usuario

Patton electronics

Patton electronics NetLink 2701/C Manual de usuario

Patton electronics

Patton electronics 470 Series Manual de usuario

Patton electronics

Patton electronics 1060RC Manual de usuario

Patton electronics

Patton electronics NetLink 1001MC Manual de usuario

Patton electronics

Patton electronics NetLink 1095RC Manual de usuario

Patton electronics

Patton electronics 1012ARC Manual de usuario

Patton electronics

Patton electronics 1206RC Manual de usuario

Patton electronics

Patton electronics 6103 Manual de usuario

Patton electronics

Patton electronics 2703RC Manual de usuario

Patton electronics

Patton electronics NetLink 2701/B Manual de usuario

Patton electronics

Patton electronics 2701RC Manual de usuario

Patton electronics

Patton electronics 1045RC Manual de usuario

Patton electronics

Patton electronics 2500RC Manual de usuario

Patton electronics

Patton electronics 3101RC Manual de usuario

Patton electronics

Patton electronics 2703RC-A Manual de usuario

Patton electronics

Patton electronics 1000RC Manual de usuario

Patton electronics

Patton electronics 1180RC Manual de usuario

Manuales populares de Tarjeta de red de otras marcas

FirstComm

FirstComm OBiWiFi5G Manual de usuario

Sun Microsystems

Sun Microsystems Interface Adapter Manual de usuario

TRENDnet

TRENDnet TU2-ETG Manual de usuario

YASKAWA

YASKAWA SI-EN3 Manual de usuario

Paradyne

Paradyne BitStorm 2600 IP DSLAM Manual de usuario

Belkin

Belkin F5D7050 Manual de usuario

3Com

3Com EtherLink 3C509B Manual de usuario

TRENDnet

TRENDnet TEG-PCITX Manual de usuario

Cisco

Cisco MC16E Manual de usuario

Delta Electronics

Delta Electronics Braking Modules VFDB Series Manual de usuario

TwinMOS

TwinMOS Booming Manual de usuario

Dialogic

Dialogic Media Board DM/V1200BTEPEQ Manual de usuario

Buffalo

Buffalo AirStation WLI-PCM-L11GP Manual de usuario

National Instruments

National Instruments NI 9234 Manual de usuario

Hama

Hama 49276 Manual de usuario

Linksys

Linksys WCF54G - Wireless-G Compact Flash Card Manual de operación

Compaq

Compaq Wireless LAN 100 Manual de usuario

Bose

Bose PowerMatch Dante Manual de usuario