PASCO ME-8594 Manual de usuario

Model No. ME-8594 012-08438A

Water Reservoir

Model No. ME-8594

Equipment List

*Use Replacement Model Numbers to expedite replacement orders.

Included Equipment Replacement

Model Number

1. Graduated Cylinder (Water Reservoir), 1 liter (1) 648-08457

2. Plastic Tubing, 19.7 feet (6 meters), 1/4” ID x 3/8” OD (1) 640-012

3. Plastic Hose Clamps (2) 640-075

Additional Equipment Suggested Model Number

Clamps, three-fingered SE-9445

Energy Transfer - Hydro Accessory ET-8772

Energy Transfer - Generator ET-8771

Large Rod Base ME-8735

Steel Rod, 90 cm ME-8738

Beaker, 1000 ml SE-7288

Water Reservoir Model No. ME-8594

Introduction

The Water Reservoir is a plastic, graduated cylinder

used as a water source for equipment such as the ET-

Hydro Accessory (ET-8772) and the ET-Generator (ET-

8771).

The Water Reservoir holds up to 1 liter of water and is

graduated in 10 increments of 100 mL and 90

increments of 10 mL. On the unmarked side of the

reservoir are three ports with three hose fittings. The

hose fittings are glued to the cylinder and are not

removable. The top fitting is for attaching the hose that

connects to an external water supply. The middle

fitting is for attaching the overflow hose, which

prevents water from overflowing the cylinder. Water

exits the cylinder through the bottom hose fitting.

Two plastic clamps are included with the reservoir to

control water flow. The Water Reservoir can be used in

two ways: 1) to supply a preset volume of water and 2)

to supply water continuously at a constant head, or pressure.

Equipment Setup

1. Cut the plastic tubing into pieces of tubing long

enough for your experiment or application. (Note: To

avoid cutting the tubing too short or too long, we

recommend that you set up and measure the tubing

length needed before cutting the tubing.)

2. Fit one piece of tubing over each of the three hose

fittings (Figure 1).

3. Attach one (or two) clamps to the bottom piece of

tubing. Tightly close the clamp to the bottom tube.

(CAUTION: If the clamp is not closed tight, water

will drain out of the bottom tube. To prevent

drainage, slip the tube through the indented portion of

the clamp, and snap the clamp completely shut.)

Note: The fittings on the Water Reservoir are oversized

to reduce friction and maximize water flow. If you have

difficulty inserting the tubing to the fitting, apply a small

amount of glycerine to the tubing.

top hose fitting

middle hose

bottom hose

Figure 1: Water Reservoir

fitting

side port

Figure 2: Water Reservoir

on rod stand

Model No. ME-8594 012-08438A

4. Use three-fingered clamps to attach the reservoir to a rod stand (Figure 2).

5. Connect the top hose to a water faucet. (Note: Keep the rod stand below the height of the

water faucet to allow water flow to travel downward.) Turn on the tap water and allow

water to flow in through the top port.

6. For a pre-measured volume: Fill the cylinder to about 800 mL, and turn off the water.

Open the clamp to the bottom tube, allow the water level to drop to the desired level, then

close the clamp.

For a constant pressure or head: Adjust the flow from the tap so that the water doesn’t

flow in from the tap faster than the overflow (from middle fitting) going to the sink.

[Note: With water flowing in from the tap and out through the overflow, the water level

stays constant (as long as the water output is less than the tap water entering the cylinder.)]

For more information about using the Water Reservoir with the ET-Hydro Accessory, see the

instruction sheets supplied with the ET-Hydro Accessory and ET-Generator Manual.

Water Reservoir Model No. ME-8594

The PASCO scientific 012-08438A Water Reservoir Instruction Sheet is copyrighted and all

rights reserved. However, permission is granted to non-profit educational institutions for

reproduction of any part of the 012-08438A Water Reservoir Instruction Sheet, providing the

reproductions are used only for their laboratories and are not sold for profit. Reproduction

under any other circumstances, without the written consent of PASCO scientific, is

prohibited.

Limited Warranty

PASCO scientific warrants the product to be free from defects in materials and workmanship

for a period of one year from the date of shipment to the customer. PASCO will repair or

replace, at its option, any part of the product which is deemed to be defective in material or

workmanship. The warranty does not cover damage to the product caused by abuse or

improper use. Determination of whether a product failure is the result of a manufacturing

defect or improper use by the customer shall be made solely by PASCO scientific.

Responsibility for the return of equipment for warranty repair belongs to the customer.

Equipment must be properly packed to prevent damage and shipped postage or freight

prepaid. (Damage caused by improper packing of the equipment for return shipment will not

be covered by the warranty.) Shipping costs for returning the equipment after repair will be

paid by PASCO scientific.

Technical Support

For assistance with the ME-8594 or any other PASCO products,

contact PASCO as follows:

Address: PASCO scientific

10101 Foothills Blvd.

Roseville, CA 95747-7100

Phone: (916) 786-3800

FAX: (916) 786-3292

Web: www.pasco.com

Email: [email protected]

Tabla de contenidos

Otros manuales de Equipo de laboratorio de PASCO

PASCO

PASCO PS-2600A Manual de usuario

PASCO

PASCO TD-8572 Manual de usuario

PASCO

PASCO ME-9454 Manual de usuario

PASCO

PASCO h/e Apparatus Manual de usuario

PASCO

PASCO OS-9255A Manual de usuario

PASCO

PASCO SE-6609 Manual de usuario

PASCO

PASCO SE-9638 Manual de usuario

PASCO

PASCO ME-9847 Manual de usuario

PASCO

PASCO ME-5707A Manual de usuario

PASCO

PASCO EM-6720 Manual de usuario

PASCO

PASCO WA-9406 Manual de usuario

PASCO

PASCO ME-8971 Manual de usuario

PASCO

PASCO TD-8565 Manual de usuario

PASCO

PASCO CI-6538 Manual de usuario

PASCO

PASCO ES-9059C Manual de usuario

PASCO

PASCO ME-9825 Manual de usuario

PASCO

PASCO ME-9430 Manual de usuario

PASCO

PASCO PASCObot Gripper PS-3325 Manual de usuario

PASCO

PASCO AP-8214 Manual de usuario

PASCO

PASCO OS-9102C Manual de usuario

PASCO

PASCO ME-6810A Manual de usuario

PASCO

PASCO TD-8498A Manual de usuario

PASCO

PASCO TD-8555 Manual de usuario

PASCO

PASCO EM-8678A Manual de usuario

Manuales populares de Equipo de laboratorio de otras marcas

Qiagen

Qiagen DML 3000 Manual de usuario

Queensgate

Queensgate NANOSCAN OP400 Manual de programación

Conviron

Conviron GEN1000-GE Manual de usuario

Parr Instrument

Parr Instrument 4560 Manual de instrucciones

IKA

IKA IC control Manual de usuario

Integra

Integra DOSE IT Manual de usuario

Agilent Technologies

Agilent Technologies 5800 ICP-OES Manual de usuario

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Manual de usuario

NI PXI-5422 Manual

Collomix

Collomix Aqix Manual de usuario

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Manual de usuario

Ocean Insight

Ocean Insight FLAME-NIR+ Manual de usuario

Parker

Parker ALIGN-MG-NA Manual de usuario

BD 644787 Manual de usuario

DENTAURUM

DENTAURUM Compact Megaplus Manual de usuario

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Manual de usuario

VWR

VWR SAS Super IAQ Manual de usuario

illumina

illumina MiSeqDx Manual de usuario