Parkside PAS 4 B4 Manual de usuario
CORDLESS SCREWDRIVER PAS 4 B4
CORDLESS SCREWDRIVER
Translation of the original instructions
AKKU-SCHRAUBER
Originalbetriebsanleitung
IAN 324364_1901
GB/IE/NI/CY Translation of the original instructions Page 1
DE/AT/CH Originalbetriebsanleitung Seite 27
Before reading, unfold the page containing the illustrations and familiarise
yourself with all functions of the device.
Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen
Sie sich anschließend mit allen Funktionen des Gerätes vertraut.
A B
9b
9a
PAS 4 B4 GB│IE│NI│CY│ 1 ■
Contents
Introduction .................................. 2
Intended use..........................................2
Notes on trademarks ...................................2
Features .............................................2
Package contents ......................................3
Technical specifications .................................3
General power tool safety warnings ............. 6
1. Work area safety ....................................6
2. Electrical safety .....................................7
3. Personal safety......................................8
4. Power tool use and care ..............................9
5. Use and handling of the cordless electrical power tool......10
6. Service ...........................................12
Safety guidelines for screw drivers........................12
Extended safety guidelines .............................13
Safety guidelines for battery chargers .....................13
Before use .................................. 14
Charging the appliance battery (see fig. A).................14
Changing bits/screw driver bits (see fig. B) .................15
Use ........................................ 16
Switching the cordless screwdriver on/off ..................16
Changing the direction of rotation ........................16
Tips and tricks........................................17
Maintenance, storage and cleaning ............. 17
Disposal .................................... 18
Kompernass Handels GmbH warranty........... 20
Service ..................................... 23
Translation of the original Conformity Declaration . 25
PAS 4 B4
■ 2 │ GB│IE│NI│CY
CORDLESS SCREWDRIVER PAS 4 B4
Introduction
Congratulations on the purchase of your new appliance. You have
chosen a high-quality product. The operating instructions are part of
this product. They contain important information about safety, usage
and disposal. Before using the product, please familiarise yourself
with all of the operating and safety instructions. Use the product only
as described and for the range of applications specified. Please also
pass these operating instructions on to any future owner.
Intended use
This appliance is designed for screwing into wood, plastic and metal.
Use this appliance only as described and for the areas of applications
specified. The appliance is not intended for commercial use. Any other
usage or modification of the appliance is deemed to be improper
and carries a significant risk of accidents. The manufacturer accepts
no responsibility for damage attributable to misuse.
Notes on trademarks
USB®is a registered trademark of USB Implementers Forum, Inc.
All other names and products may be trademarks or registered
trademarks of their respective owner.
Features
Rotation direction switch/safety lock-out
Motor direction indicator for clockwise rotation
Battery charge level indicator
Motor direction indicator for anticlockwise rotation
Charging socket
ON/OFF switch
LED lamps
Tool holder
PAS 4 B4 GB│IE│NI│CY│ 3 ■
Charger
9a
USB plug of the charging cable
9b
Micro-USB-C plug of the charging cable
Bits and bit extension
Package contents
1 cordless screwdriver
1 charger
1 case
1 charging cable
26 bits x 25mm
2 bits x 50mm
1 bit extension
1 set of operating instructions
Technical specifications
Cordless screwdriver: PAS 4 B4
Nominal voltage: 4 V (DC)
Battery (integrated): (1 cell)
Battery capacity: 1500 mAh
Rated idle speed: n0200rpm
Torque: max. 5.0 Nm
Tool holder: 6.35 mm (¼")
PAS 4 B4
■ 4 │ GB│IE│NI│CY
Use only the following charger to charge the cordless
tool:
PAS 4 B4-2:
INPUT:
Rated voltage: 100–240 V ∼ 50–60 Hz (AC)
Rated current: 16W
OUTPUT:
Rated voltage: 5.0 V (DC)
Rated current: 1700 mA
Charging time: approx. 1 hr
Protection class: II/ (double insulation)
Noise and vibration information:
The measured values have been determined in accordance with
EN62841. The A-rated noise level of the tool is typically:
Sound pressure level: LPA = 56.4 dB (A)
Sound power level: LWA = 67.4 dB(A)
Uncertainty K: KpA/WA = 3 dB
Vibration values (vector total of three directions) determined in
accordance with EN 62841:
Screws:
Vibration emission value: ah= 0.412 m/s2
Uncertainty: K = 1.5 m/s2
PAS 4 B4 GB│IE│NI│CY│ 5 ■
NOTE
► The vibration emission values and the noise emission values
given in these instructions have been measured in accordance
with a standardised test procedure and can be used for com-
parison of the power tool with another tool.
► The specified total vibration values and the noise emission
values can also be used to make a provisional load estimate.
WARNING!
► Depending on the manner in which the power tool is being
used, and in particular the kind of workpiece being worked,
the vibration and noise emission values can deviate from
the values given in these instructions during actual use of the
power tool.
► Try to keep the vibration loads as low as possible. Measures
to reduce the vibration load are, e.g. wearing gloves and
limiting the working time. Wherein all states of operation
must be included (e.g. times when the power tool is switched
off and times where the power tool is switched on but run-
ning without load).
PAS 4 B4
■ 6 │ GB│IE│NI│CY
General power tool
safety warnings
WARNING!
►Read all safety warnings, instructions, illustrations and
specifications provided with this power tool. Failure to fol-
low all instructions listed below may result in electric shock,
fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mains-operated
(corded) power tool or battery-operated (cordless) power tool.
1. Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas
invite accidents.
b) Do not operate power tools in explosive atmospheres, such
as in the presence of flammable liquids, gases or dust.
Power tools create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power
tool. Distractions can cause you to lose control.
PAS 4 B4 GB│IE│NI│CY│ 7 ■
2. Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug
in any way.
Do not use any adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will reduce risk of
electric shock.
b) Avoid body contact with earthed or grounded surfaces,
such as pipes, radiators, ranges and refrigerators. There is
an increased risk of electric shock if your body is earthed or
grounded.
c) Do not expose power tools to rain or wet conditions. Water
entering a power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away from
heat, oil, sharp edges or moving parts. Damaged or entangled
cords increase the risk of electric shock.
e) When working outdoors with an electrical power tool, always
use extension cords that are also suitable for use outdoors.
Use of a cord suitable for outdoor use reduces the risk of electric
shock.
f) If operating a power tool in a damp location is unavoidable,
use a residual current device (RCD) protected supply. Use of
an RCD reduces the risk of electric shock.
Tabla de contenidos
Idiomas:
Otros manuales de Destornillador eléctrico de Parkside
Parkside
Parkside PABS 20-Li F7 Manual de usuario
Parkside
Parkside KH 3188 2 SPEED CORDLESS DRILL Manual de usuario
Parkside
Parkside PABSS 3 Manual de usuario
Parkside
Parkside PAS 3.6 A1 Manual de usuario
Parkside
Parkside PASS 3.6 Li Manual de usuario
Parkside
Parkside PAS 4 A1 Manual de usuario
Parkside
Parkside PABS 20-Li D5 Manual de usuario
Parkside
Parkside PAS 7.2 A1 Manual del propietario
Parkside
Parkside 280213 Manual de usuario
Parkside
Parkside PABS 12 B3 Manual de usuario
Parkside
Parkside RAPIDFIRE Manual de usuario
Parkside
Parkside PABS 20-Li D5 Manual de usuario
Parkside
Parkside PEPS 3 A1 Manual de usuario
Parkside
Parkside PSSA 3.6 C4 Manual de usuario
Parkside
Parkside PSSA 3.6 C4 Manual de usuario
Parkside
Parkside PBSA 12 D2 Manual de usuario
Parkside
Parkside PABSS 3,6Li Manual de usuario
Parkside
Parkside PSSA 3.6 C3 Manual de usuario
Parkside
Parkside PBSA 12 D3 Manual de usuario
Parkside
Parkside 328024 2001 Manual de usuario
