Paradyne MIM-10/100 Manual de usuario
MIM1-A2-GZ40-00 October 2004 1
MIM-10/100
Installation Instructions
Document Number MIM1-A2-GZ40-00
October 2004
Contents
Software and Firmware License Agreement ...................................................... 1
Product Documentation Online .......................................................................... 3
Unpacking and Inspecting the Equipment ......................................................... 3
Installing the MIM-10/100 .................................................................................. 3
Connecting the Ethernet Cable .......................................................................... 4
LED Indicators ................................................................................................... 5
Regulatory Notices ............................................................................................ 5
Warranty, Sales, Service, and Training Information ........................................... 6
Software and Firmware License Agreement
The terms and conditions of this License Agreement (the “Agreement”) will apply
to the software and/or firmware (individually or collectively the “Software”)
incorporated into the Paradyne product (the “Product”) purchased by you and any
derivatives obtained from the Software, including any copy of either. If you have
executed a separate written agreement covering the Software supplied to you
under this purchase, such separate written agreement shall govern.
Paradyne Corporation (“Paradyne”) grants to you, and you (“Licensee”) agree to
accept a personal, non-transferable, non-exclusive, right (without the right to
sublicense) to use the Software, solely as it is intended and solely as incorporated
in the Product purchased from Paradyne or its authorized distributor or reseller
under the following terms and conditions:
ONCE YOU HAVE READ THIS LICENSE AGREEMENT AND AGREE TO ITS
TERMS, YOU MAY USE THE SOFTWARE AND/OR FIRMWARE INCORPORATED
INTO THE PARADYNE PRODUCT. BY USING THE PARADYNE PRODUCT YOU
SHOW YOUR ACCEPTANCE OF THE TERMS OF THIS LICENSE AGREEMENT.
IN THE EVENT THAT YOU DO NOT AGREE WITH ANY OF THE TERMS OF THIS
LICENSE AGREEMENT, PROMPTLY RETURN THE UNUSED PRODUCT IN ITS
ORIGINAL PACKAGING AND YOUR SALES RECEIPT OR INVOICE TO THE
LOCATION WHERE YOU OBTAINED THE PARADYNE PRODUCT OR THE
LOCATION FROM WHICH IT WAS SHIPPED TO YOU, AS APPLICABLE, AND YOU
WILL RECEIVE A REFUND OR CREDIT FOR THE PARADYNE PRODUCT
PURCHASED BY YOU.
2October 2004 MIM1-A2-GZ40-00
1. Ownership: The Software is the sole property of Paradyne and/or its licensors.
The Licensee acquires no title, right or interest in the Software other than the
license granted under this Agreement.
2. Licensee shall not use the Software in any country other than the country in
which the Product was rightfully purchased except upon prior written notice to
Paradyne and an agreement in writing to additional terms.
3. The Licensee shall not reverse engineer, decompile or disassemble the
Software in whole or in part.
4. The Licensee shall not copy the Software except for a single archival copy.
5. Except for the Product warranty contained in the manual, the Software is
provided “AS IS” and in its present state and condition and Paradyne makes
no other warranty whatsoever with respect to the Product purchased by you.
THIS AGREEMENT EXPRESSLY EXCLUDES ALL OTHER WARRANTIES,
WHETHER EXPRESS OR IMPLIED, OR ORAL OR WRITTEN, INCLUDING
WITHOUT LIMITATION:
a. Any warranty that the Software is error-free, will operate uninterrupted in
your operating environment, or is compatible with any equipment or
software configurations; and
b. ANY AND ALL IMPLIED WARRANTIES, INCLUDING WITHOUT
LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS
FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT.
Some states or other jurisdictions do not allow the exclusion of implied
warranties on limitations on how long an implied warranty lasts, so the above
limitations may not apply to you. This warranty gives you specific legal rights,
and you may also have other rights which vary from one state or jurisdiction to
another.
6. In no event will Paradyne be liable to Licensee for any consequential,
incidental, punitive or special damages, including any lost profits or lost
savings, loss of business information or business interruption or other
pecuniary loss arising out of the use or inability to use the Software, whether
based on contract, tort, warranty or other legal or equitable grounds, even if
Paradyne has been advised of the possibility of such damages, or for any
claim by any third party.
7. The rights granted under this Agreement may not be assigned, sublicensed or
otherwise transferred by the Licensee to any third party without the prior
written consent of Paradyne.
8. This Agreement and the license granted under this Agreement shall be
terminated in the event of breach by the Licensee of any provisions of this
Agreement.
9. Upon such termination, the Licensee shall refrain from any further use of the
Software and destroy the original and all copies of the Software in the
possession of Licensee together with all documentation and related materials.
10. This Agreement shall be governed by the laws of the State of Florida, without
regard to its provisions concerning conflicts of laws.
MIM1-A2-GZ40-00 October 2004 3
Product Documentation Online
Complete documentation for Paradyne products is available at
www.paradyne.com. Select Support →Technical Manuals.
To order a paper copy of a Paradyne document, or to speak with a sales representative,
please call 1-727-530-2000.
Unpacking and Inspecting the Equipment
HANDLING PRECAUTIONS FOR
STATIC-SENSITIVE DEVICES
This product is designed to protect sensitive components from damage
due to electrostatic discharge (ESD) during normal operation. When
performing installation procedures, however, take proper static control
precautions to prevent damage to equipment. If you are not sure of the
proper static control precautions, contact your nearest sales or service
representative.
If there is any visible damage, do not attempt to install the MIM-10/100; contact
your sales representative.
Installing the MIM-10/100
The MIM-10/100 Micro Interface Module provides additional uplink ports for the
AµD8000 ADSL Micro DSLAM or BSX8000-5 Broadband Services Switch.
NOTE: All MIMs are hot swappable, although removal of a MIM disengages the
upstream network connection for the DSLAM.
Procedure
1. Using a flat-head screwdriver to loosen the fastening screws, remove the
cover plate from the MIM port on the front of your AµD8000 or BSX8000.
CAUTION: The cover plate should be stored for possible future use: if the MIM
is removed from your AµD8000 or BSX8000, it must be replaced with either
another MIM or a cover plate. Do not operate an AµD8000 or BSX8000 with
an open MIM port.
2. Align the MIM-10/100 with the module guides inside the MIM port.
3. Slide the MIM-10/100 firmly into place. Do not use excessive force.
4. Secure the MIM-10/100 by tightening the fastening screws on the MIM
faceplate with a flat-head screwdriver.
!
4October 2004 MIM1-A2-GZ40-00
Connecting the Ethernet Cable
The Ethernet port is 10/100 auto-negotiating. Set your hub or switch to
auto-negotiate (if applicable) before making the Ethernet connection.
For most applications, the MIM-10/100 connects to a router or a PC using a
straight-through Ethernet cable and to a hub or a switch using a crossover
Ethernet cable. If you are in doubt, verify the pinouts of the device you are
connecting to.
Procedure
1. If a ferrite choke is supplied with your MIM:
— Open the ferrite choke.
— Place the choke around your Ethernet cable as close as possible to the
RJ45 connector.
— Snap shut the ferrite choke. Use a cable tie to hold it in place if it does not
fit tightly on the cable.
2. Plug the Ethernet cable into the Ethernet RJ45 port on the MIM faceplate.
3. Verify the connection; solid illumination of the Lnk LED on the MIM faceplate
indicates an Ethernet link has been established. If the Lnk LED is illuminated
but not the 100 LED, then a 10 Mbps link has been established. If the 100 LED
is also illuminated, then a 100 Mbps link has been established.
Ethernet RJ45 Port Pinouts
00-16917
Ferrite Choke
Plastic
Latch
Connector
Pin Function
Pin 1 Rx+
Pin 2 Rx-
Pin 3 Tx+
Pin 4 not used
Pin 5 not used
Pin 6 Tx-
Pin 7 not used
Pin 8 not used
MIM1-A2-GZ40-00 October 2004 5
LED Indicators
Regulatory Notices
UNITED STATES – EMI NOTICE:
!
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
The authority to operate this equipment is conditioned by the
requirements that no modifications will be made to the equipment
unless the changes or modifications are expressly approved by
Paradyne Corporation.
Table 1. LEDs
LED STATE INDICATION ADDITIONAL INFORMATION
100 Solid Green Fast Ethernet connection
(100 Mbps) is established.
If the 100 LED is illuminated, the Lnk LED
will also be illuminated.
No Illumination No Fast Ethernet
connection.
If the 100 LED remains unlit but the Lnk
LED is illuminated then a link has been
established at 10 Mbps rather than 100
Mbps.
Act Flashing Amber Ethernet activity. Traffic is flowing without any problems.
Solid Amber Heavy traffic.
No Illumination No Ethernet activity. Either there is no Ethernet link or a link
exists but there is no activity.
Lnk Solid Green Ethernet connection is
established.
If the Lnk LED is illuminated but not the
100 LED then a 10 Mbps link has been
established. If the 100 LED is also
illuminated, then a 100 Mbps link has
been established.
No Illumination No Ethernet connection. The 100 and Act LEDs will remain unlit by
default.
!
6October 2004 MIM1-A2-GZ40-00
CANADA – EMI NOTICE:
!
This Class A digital apparatus meets all requirements of the Canadian
interference-causing equipment regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du
règlement sur le matérial brouilleur du Canada.
EUROPEAN REGULATORY COMPLIANCE
The following regulatory compliance information applies to the
MIM-10/100 as installed in the AµD8000 or BSX8000-5:
This Class A product complies with European Norm EN55022.
Warning: In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate
measures to correct the situation.
Warranty, Sales, Service, and Training Information
Contact your local sales representative, service representative, or distributor
directly for any help needed. For additional information concerning warranty, sales,
service, repair, installation, documentation, training, distributor locations, or
Paradyne worldwide office locations, use one of the following methods:
Internet: Visit the Paradyne World Wide Web site at www.paradyne.com.
(Be sure to register your warranty at www.paradyne.com/warranty.)
Telephone: Call our automated system to receive current information by fax or
to speak with a company representative.
— Within the U.S.A., call 1-800-870-2221
— Outside the U.S.A., call 1-727-530-2340
!!.
*MIM1-A2-GZ40-00*
!
Copyright ©2004 Paradyne Corporation. Printed in U.S.A.
Tabla de contenidos
Otros manuales de Hardware de red de Paradyne
Paradyne
Paradyne FrameSaver NP 100 Manual de usuario
Paradyne
Paradyne T1 Access Mux 916x Manual de uso y cuidado
Paradyne
Paradyne Hotwire 5620 Manual de usuario
Paradyne
Paradyne Jetstream CPX-1000 Manual de usuario
Paradyne
Paradyne 7511 Manual de usuario
Paradyne
Paradyne 8540 Manual de usuario
Paradyne
Paradyne ACCULINK 316x Manual
Paradyne
Paradyne Hotwire 8784 Manual de usuario
Paradyne
Paradyne 8310 MVLt Manual de usuario
Paradyne
Paradyne ACCULINK 317x E1 Manual
Paradyne
Paradyne 3160-A4 Manual
Paradyne
Paradyne Hotwire 7995 Manual de usuario
Paradyne
Paradyne Fan Tray 8820-S2-900 Manual de usuario
Paradyne
Paradyne 3163 Manual de usuario
Paradyne
Paradyne COMSPHERE 3610 Manual de usuario
Paradyne
Paradyne Hotwire 7996 Manual de usuario
Paradyne
Paradyne SMD2000-24E Manual de usuario
Paradyne
Paradyne COMSPHERE 3610 Manual de operación y mantenimiento
Paradyne
Paradyne 9126 Manual de usuario
Paradyne
Paradyne COMSPHERE 3610 Manual de lista de piezas
Manuales populares de Hardware de red de otras marcas
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manual de usuario
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manual de usuario
Yudor
Yudor YDS-16 Manual de usuario
D-Link
D-Link ShareCenter DNS-320L Manual de usuario
Samsung
Samsung ES1642dc Instrucciones de uso
Honeywell Home
Honeywell Home LTEM-PV Instrucciones de montaje
