Paradyne 6310 MVLT Manual de usuario

Hotwirer6310 MVLtModem Customer Premises

Installation Instructions

Document Number 6310-A2-GN10-40

February 2000

Contents

Hotwire 6310 MVL Modem Overview 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Before You Begin 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installing the Hotwire MVL Modem 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Power-On 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Troubleshooting 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

MVL HomeLink 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Cables & Connectors 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Important Safety Instructions 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Hotwire 6310 MVL Modem Overview

The Hotwirer6310 MVLt(Multiple Virtual Lines) Modem is a component in the

Hotwire MVL System and interoperates with the Hotwire 8310 or 8312 MVL Card in the

DSLAM (Digital Subscriber Line Access Multiplexer) system. This system provides

high-speed Internet or corporate LAN access over traditional twisted-pair copper

telephone wiring.

The MVL technology:

HTransforms a single copper pair into multiple virtual lines to support multiple

services simultaneously.

HOperates over existing copper wire with existing telephone jacks.

HProvides rate adaptive data rates to dynamically adapt and allocate bandwidth to

optimize applications.

HSupports simultaneous multiple access of four MVL modems with up to

254 end-user systems sharing one common WAN interface.

HFeatures HomeLink which provides peer-to-peer communications, including print

and file sharing applications.

HUtilizes a POTS (plain old telephone service) splitterless environment at the

customer premises.

HProvides ability to obtain software upgrades online.

Hotwire MVL System

Copper pairs run from the central office (CO) to the customer premises (CP) to create

the local loop. The local loop terminates on the customer premises at the demarcation

point.

98-15930a-02

MVL

Modem

Customer Premises (CP)

MVL/POTS

Ethernet

Crossover

Cable Ethernet

Cable

Central

Office

(CO) Local Loop

Hub

MVL – Multiple Virtual Lines

POTS – Plain Old Telephone Service

End-user

Systems

(up to 32)

Network

Service

Provider

(NSP) Demarcation

Point

MVL Access with a Hotwire MVL POTS Filter

When a Hotwire 6035 or 6040 MVL POTS Filter is used, one filter is installed for each

telephone on the same phone line as MVL.

99-16580

RJ11

Wall Jack

RJ11

Wall

Jack

MVL Modem

Customer

Premises (CP)

PHONE

POWERETHERNET

LINE

PHONE

POWERETHERNET

LINE

FAX

MVL Modem

6035

Phone Filter

POTS Filter 6040

Wall Jack

Phone

Filter

NOTES:

In this document:

—A telephone is used to represent any equipment that plugs into a phone jack

and uses the POTS line, such as a phone, modem, or fax machine.

—End-user system is used to represent any PC with an Ethernet connection and

MVL-based service.

—Service provider is used to represent any Internet Service Provider (ISP) or

remote LAN access provider.

Before You Begin

Verify that your package contains the following:

-Hotwire 6310 MVL Modem

-MVL interface cable with RJ11 connectors

-Power cord with power transformer

-One ferrite choke

Be sure to register your warranty at www.paradyne.com/warranty.

Wiring and Cables You Need

The following wiring and standard connectors are used with this product:

-Standard RJ11 wall jack for the MVL cabling.

-Standard Ethernet 8-pin, non-keyed modular plug for a PC or workstation.

An Ethernet straight-through or crossover cable is used. Refer to Installing the

Hotwire 6310 MVL Modem on page 4 for Ethernet cable details.

MVL Phone Filter

Depending on the type of telephone handset and the quality of the home or business

wiring, a phone filter is recommended to improve data transmission throughput and

minimize background noise during a telephone conversation.

There are two Hotwire MVL Phone Filters:

HHotwire 6035 MVL Phone Filter designed for use with a tabletop phone.

HHotwire 6040 MVL Wall Jack Phone Filter designed for use with a wall phone.

Product-Related Documents

To install a phone filter, refer to the appropriate document:

Document Number Document Title

6035-A2-GN11 Hotwire 6035 MVL Phone Filter Installation Instructions

6040-A2-GN11 Hotwire 6040 MVL Wall Jack Phone Filter Installation

Instructions

Contact your sales or service representative to order additional product documentation.

Paradyne documents are available on the World Wide Web at www.paradyne.com.

Select Library →Technical Manual →Hotwire DSL & MVL Systems.

Installing the Hotwire 6310 MVL Modem

Place the Hotwire 6310 MVL Modem on a flat surface with clearance for the rear

connectors.

"Procedure

1. If a telephone is installed, unplug the telephone line from the RJ11 wall jack.

2. Use the supplied RJ11 6-pin interface cable for the MVL LINE connection. Insert

one end of the cable into the jack labeled LINE. Insert the other end of the cable

into the RJ11 wall jack.

PHONE

98-15895

RJ11

Wall Jack

POWER ETHERNET

LINE

MVL Modem

3. Connect a telephone (optional); go to Step 4 if you are not connecting a telephone

to the MVL modem.

The 6035 phone filter has a cable attached. Plug the other end of this cable into

the MVL modem jack labeled PHONE. Using the existing telephone interface cable

that was unplugged in Step 1, plug into the POTS filter jack labeled PHONE.

99-16239-01

MVL Modem

PHONE

POWER ETHERNET

LINE

Supplied

Cable

Existing Cable

LINE

PHONE

4. Use an 8-pin Ethernet cable for the Ethernet connection. Insert one end of the

cable into the jack labeled ETHERNET.

HUse a straight-through cable and connect the other end to an Ethernet hub.

Do not connect a straight-through cable to the external hub’s UPLINK

connection (this connection requires a crossover cable),

PHONE

POWER ETHERNET

LINE

MVL Modem

98-15906

Ethernet

Line

Ethernet

Hub Ethernet

Cable

–or –

HUse an Ethernet crossover cable and connect the other end to a PC with an

Ethernet Network Interface Card (NIC) installed.

PHONE

POWER ETHERNET

LINE

MVL Modem

98-15907

Ethernet

Line

PC with Ethernet

Network Interface

Card Ethernet

Cable

For MVL modem cable pin assignments, refer to Cables & Connectors on page 10.

5. Insert the supplied power cord’s round end into the jack labeled POWER. Attach

the supplied ferrite choke as closely as possible to the MVL modem. Pass the

cable through the ferrite choke twice, creating a loop as shown. Close the two

halves around the ferrite choke and snap the ferrite choke shut. Plug the

transformer into an ac outlet.

PHONE

POWER ETHERNET

LINE

MVL Modem

00-16352-01

Power

Jack

Ferrite

Choke

The MVL modem hardware installation is now complete. When the power cord is

installed, the MVL modem goes through a power-on self-test.

Power-On

When power is applied, the MVL modem performs self-diagnostics and the PWR LED

is on. The self-diagnostics includes a power-on self-test and all of the LEDs turn on for

one second.

TST LINE ETHERNET

ALMPWR

99-15896-01

Power –green

Alarm –red

Test –yellow

Transmit/Receive –green

Ethernet Link –green

MVL

MODEM

TX/RX

MultipleVirtual Lines –green

Refer to Troubleshooting on page 8 for LED indications requiring action.

Status LEDs

All of the LEDs turn on and off during the power-on self-test. After a successful

self-test, the LEDs should appear as indicated in BOLD in the Condition column below.

LED State Status

PWR ON MVL modem has power.

ALM OFF

No active alarms.

An alarm condition exists.

TST OFF

No active tests.

The TST LED is on during the power-on self-test and during a

test initiated by the Service Provider.

LINE ON

OFF

The MVL link is active and ready to transmit and receive data.

The MVL link has not been established.

TX/RX ON

OFF

Data transmission is in progress on the MVL line.

The modem is not transmitting or receiving data.

ETHERNET ON

OFF

The Ethernet connection to the Ethernet hub or PC is active.

No Ethernet 10BaseT device is detected.

Troubleshooting

LED Symptom Action

All LEDs are on. If LEDs remain on after ten minutes, the modem is not

functional. Contact the Service Provider.

ALM LED remains

on. The power-on self-test may have failed. Unplug the unit and

reapply power. If the alarm LED is still on, contact the Service

Provider.

ALM and TST

LEDs are blinking. Firmware download may be in progress. If firmware download

is not in progress or the LEDs continue blinking after ten

minutes, contact the Service Provider.

Ethernet LED is off. Verify that the Ethernet cable is securely installed at both ends,

and at least one PC is connected and powered on.

Verify that the correct straight-through or crossover cable is

installed. Refer to Installing the Hotwire 6310 MVL Modem on

page 4.

LED Symptom Action

LINE LED is off. Verify that the MVL LINE cable is securely installed on both

ends. If the problem continues, contact the Service Provider.

Verify that the line has dial tone. If there is no dial tone, contact

the Service Provider.

LINE LED is on and

there is no data

transmission.

The MVL link has been established but there is no data

transmission. Verify the Ethernet connection. If the problem

persists, contact the Service Provider.

LINE and Ethernet

LEDs are on and

there is no data

transmission.

The MVL and Ethernet links have been established but there is

no data transmission. If the problem continues, contact the

Service Provider.

PWR LED is off. Check that the power cord is securely installed on both ends.

If no LEDs are on, the power supply may be defective. Test the

outlet to verify power. If the problem persists, contact the

Service Provider.

If other LEDs are on, the PWR LED may be burned out. Unplug

the unit and reapply power; watch all LEDs during the

power-on self-test to verify if the PWR LED is functioning.

TST LED is on. A test initiated by the Service Provider may be active. Wait five

minutes. If the TST LED does not go off, contact the Service

Provider.

To improve data transmission throughput and minimize background noise during a

telephone conversation, make sure that:

HThe Hotwire 6310 MVL modem is always powered on, even when not in use, and

HA Hotwire MVL phone filter is installed on every telephone.

MVL HomeLink

MVL HomeLink is a feature that provides peer-to-peer communications for PCs

attached to different MVL modems at the customer premises.

For example, PCs that are not connected to the same physical Ethernet LAN can now

take advantage of the resources of the primary office computer. With the Microsoft

Windows operating system, multiple end-user systems can share resources, including:

HFile sharing

HPrint sharing

HSecondary computer backup

98-15304a

6-Pin

RJ11 Plugs

Pin #1

Pin #6

To enable the sharing of resources and review security considerations, see Microsoft’s

Web site at www.microsoft.com.

In this example of HomeLink, the PC in the family room could use the office printer.

98-15952a-01

RJ11

Wall

Jack

MVL Modem

Office

PHONE

POWER ETHERNET

LINE

Hub

FAX

Ethernet

Cable Printer

RJ11

Wall

Jack

PHONE

POWER ETHERNET

LINE

MVL Modem

Family Room

Increasing the Number of End-User Systems

A single end-user system is attached to the Hotwire 6310 MVL Modem by using an

Ethernet crossover cable. To increase the number of end-user systems, connect all the

PCs to an Ethernet hub using a straight-through cable.

On one line, the MVL system provides the capability to use up to four 6310 MVL

modems and 32 end-user systems in any combination.

Cables & Connectors

This section is reference information.

Standard twisted-pair CAT3 or better cables are recommended.

HThe LINE and PHONE interface connectors use 6-pin, non-keyed modular plugs.

RJ11 6-Pin Connector

Pin # Function

1 & 2 Not used

3MVL Ring

4MVL Tip

5 & 6 Not used

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Módem de Paradyne

Paradyne

Paradyne COMSPHERE 3800PLUS Manual de usuario

Paradyne

Paradyne Hotwire 7976 Manual de usuario

Paradyne

Paradyne COMSPHERE 3910 Manual de usuario

Paradyne

Paradyne COMSPHERE 3830 Manual del operador

Paradyne

Paradyne COMSPHERE 3825Plus Manual de usuario

Paradyne

Paradyne HotWire 7915 Manual de usuario

Paradyne

Paradyne COMSPHERE 3810 Instrucciones de montaje

Paradyne

Paradyne Hotwire 8775 Manual de usuario

Paradyne

Paradyne HotWire 7915 Manual de instrucciones

Paradyne

Paradyne 3920 Guía de inicio rápido

Paradyne

Paradyne FrameSaver FLEX 9123 Manual de usuario

Paradyne

Paradyne HOTWIRE 7900 Manual de usuario

Paradyne

Paradyne 6381-A3 Instrucciones de funcionamiento originales

Paradyne

Paradyne Hotwire 6205 Manual de usuario

Paradyne

Paradyne COMSPHERE 3000 Series Manual de usuario

Paradyne

Paradyne COMSPHERE 3821PLUS Manual de usuario

Paradyne

Paradyne Hotwire 8300 Manual de usuario

Paradyne

Paradyne COMSPHERE 3810 Instrucciones de instalación

Paradyne

Paradyne COMSPHERE 3920PLUS Series Manual de usuario

Paradyne

Paradyne KeepInTouch 3760 Manual de usuario

Paradyne

Paradyne COMSPHERE 3821PLUS Manual de operación y mantenimiento

Paradyne

Paradyne COMSPHERE 3610 Manual de instrucciones

Paradyne

Paradyne 39xx Series Manual de operación y mantenimiento

Paradyne

Paradyne 2001 Manual de instrucciones

Manuales populares de Módem de otras marcas

Davicom

Davicom DM562AP Manual de usuario

EpiValley

EpiValley TATA indicom SXC-1080 Manual de usuario

Zte

Zte WiMAX Manual de usuario

Intelimax

Intelimax MA-2060 Manual de usuario

SMC Networks

SMC Networks D3CM1604V Manual de uso y cuidado

Telstra

Telstra Wi-Fi 4G Advanced Pro X Manual de usuario

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Manual de usuario

Samsung

Samsung AceLink SAM-335A Manual de usuario

Enfora

Enfora Enabler-G Guía de configuración rápida

iRZ

iRZ ATM2-232 Manual de usuario

Zhone

Zhone 6310 Manual de usuario

US Robotics

US Robotics 3453C Manual de usuario

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Manual de usuario

Zte

Zte MF823 Manual de usuario

Four-Faith

Four-Faith F1403 Manual de usuario

Sierra Wireless

Sierra Wireless AIRLINK MP595W Manual de usuario

Gemtek

Gemtek WiMAX WIXFBR-103 Manual de usuario

Zoom

Zoom 1070 Series Manual de usuario