Panduit CDE2 Manual de usuario

INSTRUCTIONS CM429A

FOR TECHNICAL SUPPORT www.panduit.com/resources/install_maintain.asp

(1) Switch Ducting

(with hinged Perforated Door)

Page 1 of 4

Component Guide

TOOL LIST

#2 Philliips Screwdriver

5/16” Socket Wrench

3/8” Socket Wrench

1/4” Socket Driver

(1) Hardware Kit

(not shown)

(1) Switch Support Bracket

CDE2

(installed in Net-Access

Server Cabinet)

Modular ToR Switch Inlet Duct

(CDE2)

Cisco Nexus 2000 Series Switch

(reference)

INSTRUCTIONS CM429A

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 2 of 4

Determine Location of Switch Ducting and Switch Support Bracket

NOTES: Front to back span of equipment rails may need to be adjusted to accomodate your switch. See table below for front to rear rail

spacing requirements. Equipment installed directly below CDE2 may impede routing of switch power cord if installed prior to CDE2.

Switch Ducting and Switch Support Bracket components of CDE2 require two (2) rack spaces for installation. Switch Ducting and Switch

Support Bracket are to be installed at the same vertical rack position. CDE2 components are to be installed prior to switch installation and

are designed to support the switch. (CDE2 ducting system ONLY requires use of primary Cisco rack mount brackets. Cisco supplied

switch cradle or extension brackets are not compatible with CDE2.)

Grounding Cage Nut

(green)

Cage Nut

(installed)

Intended

Mounting

Location

(2 rack spaces)

1 RU Switch

(reference; port side of

switch faces Hot Aisle)

Install Cage Nuts

Insert (2) cage nuts per equipment rail at CDE2 component mounting locations (8 total cage nuts are to be installed). (1) grounding cage

nut (green) must be installed in each equipment rail. The view below depicts cage nut locations for (1) intended mounting location.

Switch Ducting

Switch Support Bracket

Intended

Mounting

Location

(2 rack spaces)

Intended Mounting Location

(2 rack spaces)

Perforated Door of Switch Ducting

(faces Cold Aisle)

FRONT OF

CABINET

REAR OF

CABINET

INSTRUCTIONS CM429A

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 3 of 4

Install Switch Ducting

Position Switch Ducting so that the perforated door of ducting faces the cold aisle and the mounting holes of Switch Ducting align with

cage nuts in equipment rails (installed on page 2). Secure Switch Ducting to equipment rails using (1) #12-24 Phillips screw and (1) hex

head grounding screw (green; use 5/16” socket wrench) per rail. Ensure that hex head grounding screws fasten into grounding cage nuts.

(2) #12-24 Hex Head

Grounding Screws

(use 5/16” socket wrench)

Switch Ducting Perforated Door of Switch Ducting

(faces Cold Aisle)

Install Switch Support Bracket

Position Switch Support Bracket so that the mounting holes of Switch Support Bracket align with cage nuts in equipment rails (installed on

page 2). Secure Switch Support Bracket to equipment rails using (1) #12-24 Phillips screw and (1) hex head grounding screw (green; use

5/16” socket wrench) per rail. Ensure that hex head grounding screws fasten into grounding cage nuts.

Grounding Cage Nuts

(green)

Cage Nuts

(installed)

(2) #12-24 Phillips Screws

(2) #12-24 Hex Head

Grounding Screws

(use 5/16” socket wrench)

(2) #12-24 Phillips Screws

Cage Nuts

(installed)

Grounding Cage Nuts

(green)

Switch Support

Bracket

FRONT OF

CABINET

REAR OF

CABINET

FRONT OF

CABINET

INSTRUCTIONS CM429A

For Instructions in Local Languages

and Technical Support:

www.panduit.com/resources/install_maintain.asp

E-mail:

[email protected]

Fax:

(708)444-6448

www.panduit.com

Page 4 of 4

Routing of Switch Power Cable

NOTE: Dashed outline of 1 RU Switch is shown for power cord routing reference only.

DO NOT INSTALL SWITCH AT THIS TIME. Cabinet and equipment rails are not shown to add clarity to view.

Prior to switch installation, route power cord through Switch Ducting and Switch Support Bracket as shown. Slit grommet(s) along guide

lines as needed to allow for power cord pass-through. Use bridge features on Switch Support Bracket as tie-down point(s) to secure

switch power cord to Switch Support Bracket with cable tie.

Switch Ducting

Switch

Support

Bracket

Install Switch

NOTE: Cabinet and equipment rails are not shown to add clarity to view.

Slide the 1 RU Switch onto positioning flanges of Switch Support Bracket. Carefully insert inlet side of switch into rear opening of Switch

Ducting. Position holes of 1 RU Switch rack mount brackets over threaded studs of Switch Support Bracket. Secure switch to Switch Sup-

port Bracket with (4) #10-32 acorn nuts (use 3/8” socket wrench).

Switch Power Cord

(to rear-mounted power

outlet unit)

FRONT OF CABINET REAR OF CABINET

Slit Grommet(s) along guide lines as needed

to allow for power cord pass-through

Bridge Feature

(use as tie-down

point for cable tie)

FRONT OF CABINET 1 RU Switch

(reference; port side of

switch faces Hot Aisle)

Positioning

Flange

Rear Opening of

Switch Ducting

(4) #10-32 Acorn Nuts

(use 3/8” socket wrench)

Positioning

Flange

Switch Power Cord

REAR OF

CABINET

Otros manuales de Cambiar de Panduit

Panduit

Panduit ATLONA Opus AT-OPUS-RX41 Manual de usuario

Panduit

Panduit PN380 Manual de usuario

Panduit

Panduit Network Switch Manual de usuario

Panduit

Panduit ATLONA AT-HDR-SW-51 Manual de usuario

Panduit

Panduit ATLONA AT-UHD-CLSO-601 Manual de usuario

Panduit

Panduit ATLONA Omega AT-OME-MH21 Manual de usuario

Panduit

Panduit Atlona OmniStream Series Manual de usuario

Panduit

Panduit DPOE24S1XY Manual de usuario

Panduit

Panduit Atlona AT-HDVS-150-TX-HDMI Manual de usuario

Panduit

Panduit ATLONA Omega AT-OME-MH21 Manual de usuario

Panduit

Panduit DPOE12U1XY Manual de usuario

Panduit

Panduit ATLONA AT-HDR-SW-51 Manual de usuario

Panduit

Panduit Atlona AT-JUNO-451-HDBT Manual de usuario

Panduit

Panduit ATLONA Omega AT-OME-MH21 Manual de usuario

Panduit

Panduit Atlona JunoX 451 Manual de usuario

Panduit

Panduit Atlona AT-HDVS-200-TX Manual de usuario

Panduit

Panduit Atlona AT-UHD-SW-5000ED Manual de usuario

Panduit

Panduit Atlona AT-HDR-SW-52ED Manual de usuario

Panduit

Panduit Atlona AT-HDVS-210H-TX-WP Manual de usuario

Panduit

Panduit Atlona AT-UHD-SW-51 Manual de usuario

Panduit

Panduit ATLONA AT-UHD-CLSO-601 Manual de usuario

Panduit

Panduit Atlona Omega Series Manual de usuario

Panduit

Panduit Atlona AT-HDVS-210U-TX-WP Manual de usuario

Panduit

Panduit Atlona Omega AT-OME-PS62 Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario