Panduit NetFrame NFR84 Manual de usuario

INSTRUCTIONS CM281G

FOR TECHNICAL SUPPORT www.panduit.com/resources/install_maintain.asp

Page 1 of 4

Modular NETFRAME™Rack and Accessories

Part Numbers: NFR84, NFD484, NFSK, NFDR4X6K, NFCDRK, NFVSM4, NFEDB23,

NFSHLF19X18, NFSHLF19X25, NFLRB, NFEP, NFD884, NFD1284, NFREB2, NFBRFK

Optional Accessories

NFR84

Modular NETFRAME Rack

(8) D-rings

NFDR4X6K

Rack Assembly

(1) Vertical

Slack Manager

NFVSM4

Step1

Lay the two vertical channels

on the floor or a pair of sturdy

saw horses to ease installa-

tion.

Install (1) Base Angle and

Front Top Flange on the verti-

cal channels using (8) 3/8”

bolts, lockwashers and nuts

provided. Do not tighten.

19” Mounting 23” Mounting

(2) Vertical Channels

(2) Base Angles

(1) Pack of (20) 3/8x1.00

Bolt, Lockwasher, Nut

(1) Front Top Flange

(1) Rear Top Flange

(2) Center Waterfalls

(1) Pack of (25) #12-24x1/2” Screws

(1) Grounding and Hardware Kit

(16) Center

D-rings

NFCDRK

(1) NETFRAME Extender

Door Brackets for

23” Mtg

(4) #10-32 Screws

NFEDB23

(1) End Panel

(6)3/8”-16x1.625” Hex Bolts

3/8”-16 Hex Nuts

3/8” Split Lockwashers

NFEP

(1) Ladder Rack

Bracket

(2)3/8”-16x1” Hex Bolts

3/8”-16 Hex Nuts

3/8” Split Lockwasher

NFLRB

(1) Shelf

(4) #12-24 Screws

NFSHLF19x18

NFSHLF19x25

(shown)

(1) Door, 4” wide w/

Mtg Brackets

(4) #10-32 Screws

NFD484

(1) Center

Door, with

brackets

NFD884

NFD1284

(2) Rear Extender

Bracket

(8) #12-24 Screws

NFREB2

(8) Bend Radius Fingers

NFBRFK

Vertical

Channel

Base Angle

Front Top

Flange

Step 2

Roll the rack on its side to install

the other base angle and rear

top flange using (8) 3/8” bolts,

lockwashers and nuts provided.

Do not tighten.

Rear Top Flange

Base Angle

(1) Spool

(2)#12-24 Screws

NFSK

INSTRUCTIONS CM281G

FOR TECHNICAL SUPPORT www.panduit.com/resources/install_maintain.asp

Page 2 of 4

23.875

28.40

11.00

17.00

6.00

Location Guide: 19” Rack

Step 3

Stand the rack upright.Verify

#12-24 tapped holes are EIA

spaced at 18.31”, square the

rack and tighten bolts.

Install the two waterfalls with

the #10-32 screws provided.

Mount rack to floor using the location guide below for

mounting hole and overall size information.

Center Waterfall

Grounding Kit

(1) Barrel Lug

(1) 1/4”-20 Screw

Barrel Lug and

Grounding Screw

mounts to rear of

rack in one of four

optional places.

Rear

Bracket

Front

Bracket

Shelf

Plate

#10-32 Screws

C Channel J Slot

Flush

Mount

6 in.

Mount

Attach Rear Bracket to rear of

rack at desired height with

#12-24 screws. Attach Front

Bracket to front of rack at

desired height with #12-24

screws. Attach Shelf Plate to

Front and Rear Brackets with

the #10-32 screws. The Shelf

Plate “C” Channel mates with

the bracket “J’ Slot to provide

adjustable mounting. Can be

mounted “flush” or extended 6

inches.

Shelf Installation

NFSHLF19X18, NFHSLF19X25

Rear Extender Bracket Installation

NFREB2

(2) #12-24

SCREWS

Use (2) #12-24 screws to secure each

bracket in desired location

NFLRB Top Plate

attaches to Main

Bracket with (2) 3/8”-

16x1” hex bolts, 3/8”-16

hex nuts and 3/8” split-

lockwashers provided

NFLRB Top Plate

can be assembled

perpendicular to

Main Bracket to

support parallel

runs of ladder rack.

NFLRB assembles to

NFR84 using 3/8”-16x1”

hex bolt, nut, and lock-

washer provided with

NFR84

Ladder Rack Bracket Installation

NFLRB

End Panel

NFEP

NFEP attaches to

rack with (6) 3/8”-

16x.625” Hex Bolts,

3/8”-16 Hex Nuts

and 3/8” Split Lock-

washers provided.

NFEP

INSTRUCTIONS CM281G

FOR TECHNICAL SUPPORT www.panduit.com/resources/install_maintain.asp

Page 3 of 4

Right side installa-

tion snaps down

Left side installation

snaps up

NFDR4x6K

D-Rings Installation:

NFDR4X6K

Center D-Rings Installation:

NFCDRK

Fingers install by snapping (down right side)

(up left side) use (3) #12-24 screws to secure

each finger section in desired location.

Note:

Start finger installation from bottom of rack and

continue upwards on the right side. Start finger

installation from top of rack and continue down

on the left side.

NETFRAME Vertical Slack Manager: NFVSM4

Spool Installation

Step 1

Align buttons with

mounting leg slot

Step 3

Apply downward pres-

sure until plastic spool

clicks into place.

Step 2

Push buttons through back-

bone until mounting face is

flush with backbone.

Removal/Replacement

Step 4

Pull back on angled flange while

applying upward pressure

Step 5

Repeat steps 1-3

Angled Flange

Side Mount EIA/NETFRAME Racks

Vertical Slack Manager attaches to your frame with (3) 3/

8” bolts, nuts and lock washers.

Bend Radius Fingers Installation

NFBRFK

INSTRUCTIONS CM281G

For instuctions in Local Languages

and Technical Support:

www.panduit.com/resources/install_maitain.asp

E-mail:

[email protected]

Fax

(708)444-6448

www.panduit.com

Page 4 of 4

1. Use 3/8”-16x1” bolt, 3/8”-16 nut and 3/8” lockwasher provided with NETFRAME to gang two racks

together using NETFRAME junction holes located on side of rack channels.

2. Straddling the two racks, fasten Top Bracket and Bottom Bracket with #10-32x5/16” screws provided.

3. Door installs to top and bottom brackets by aligning lower hinge pin to hinge pin mounting hole.

Squeeze knobs together, then align upper hinge pin to upper hinge pin mounting hole. Release pressure

on knobs to set door in place.

Top

Bottom Bracket

NFD884

NFD484 installed to NETFRAME with

(4) #10x32 screws provided.

Door Installation

NFD484

NFEDB23

NFEDB23 installed to

NETFRAME Top Flange

with #10-32 screws

provided. To be used

when rack is set-up for

23” mounting

Center Door

NFD884

NFD1284

NFSK attaches to

rack with (2) #12-24

screws provided

Spool

NFSK

Este manual sirve para los siguientes modelos

Otros manuales de Rack y soporte de Panduit

Panduit

Panduit PZWIFICB Manual de usuario

Panduit

Panduit NET-ACCESS S2RP Manual de usuario

Panduit

Panduit Basic Rack PDU Manual de usuario

Panduit

Panduit SN5RC Manual de usuario

Panduit

Panduit R4P Manual de usuario

Panduit

Panduit R4P Manual de usuario

Panduit

Panduit SN7VCM Manual de usuario

Panduit

Panduit NREPB1 Manual de usuario

Panduit

Panduit Atlona AT-OME-WP-BKT Manual de usuario

Panduit

Panduit NET-ACCESS CN3 Manual de usuario

Panduit

Panduit PATMFM4.0 Manual de usuario

Panduit

Panduit ATLONA AT-RACK-1RU-ME Manual de usuario

Panduit

Panduit Net-Verse D Series Manual de usuario

Panduit

Panduit ATLONA AT-VTP-VTM Manual de usuario

Panduit

Panduit Net-SERV Manual de usuario

Panduit

Panduit NET-ACCESS NACSS Manual de usuario

Panduit

Panduit NET-ACCESS NVBP Manual de usuario

Panduit

Panduit CM599H Manual de usuario

Panduit

Panduit Atlona AT-VTP-FMK-10 Manual de usuario

Panduit

Panduit Atlona AT-HDVS-CAM-CMNT Manual de usuario

Manuales populares de Rack y soporte de otras marcas

Salamander

Salamander Acadia AC/W/L400/WH Manual de usuario

Fohhn

Fohhn VAT-09 Guía del usuario

ricoo

ricoo FS0522 Manual de usuario

AMSOIL

AMSOIL BMK-22 Guía rápida

Kargo Master

Kargo Master 48220 Manual de usuario

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manual de usuario

ricoo

ricoo S1222 Manual de usuario

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manual de usuario

VidaBox

VidaBox VB MNT FFS2 Manual de usuario

Welch Allyn

Welch Allyn 48960 Manual de usuario

Arkon

Arkon CM035-ST-2 Manual de usuario

PROEL

PROEL PLWIN60C Manual de usuario

Agilent Technologies

Agilent Technologies E2609B Manual de usuario

Mustang

Mustang MV-ARM4 Manual de usuario

Mounting Solutions

Mounting Solutions WRM-320 Manual de usuario

Pyle

Pyle PMKSPAD1 Manual de usuario

ShelterIt

ShelterIt 21208 Manual de usuario

SPL

SPL RackPack?4 1040 Manual de usuario