Panduit CT-1123 Manual de instrucciones

Page: 1 of 2

Website: www.panduit.com

E-mail: [email protected]

For Technical Support:

888-506-5400, ext. 3255

Fax.: 630-759-7532

CT-1123 and CT-1104

PA25121A01

REV: 00 3-2006

CONTROLLED CYCLE FERRULE CRIMPING TOOLS

OPERATION, INSPECTION and MAINTENANCE INSTRUCTIONS

1. With the handles in the open position, insert the ferrule

into the crimp pocket. Make sure that the ferrule is

inserted fully into the crimp die (see Figure 2).

2. Insert the stripped wire into the ferrule until the wire

stops. Refer to ferrule packaging for wire strip length.

3. Crimp the ferrule by closing the handles until the

controlled cycle mechanism releases. Upon release,

the handles will open automatically and the crimped

ferrule can be removed.

CT-1123 and CT-1104 TOOLS

Cushioned handle grips

Self-adjusting crimp die

for Insulated and non-

insulated ferrules.

Ferrule size dependent on

wire gage.

Refer to ferrule packaging

for proper ferrule and wire

combinations.

Controlled cycle

mechanism prevents tool

from opening before

crimp cycle is

complete.

Fig. 1

Fig. 2

Stripped

Wire Crimp Die

Ferrule

CAUTION:

Verify power is “OFF” before working on

wiring with these tools.

The plastic grips are for the user’s

comfort, and are not intended

to insulate against electrical shock while

working on live electrical circuits.

CT-1123 Tool

(CT-1104 Tool not shown)

Manual release lever,

push forward in the event

that controlled cycle

mechanism must be

released.

Page: 2 of 2

NEW TOOLS - BEFORE PLACING INTO SERVICE:

All

PANDUIT

crimping tools are calibrated and inspected before they are shipped from the factory. All new tools should

be inspected before being used.

New tools are shipped, factory lubricated, in protective packaging. After inspection, simply clean any excess oil from the

crimping dies and place into service.

When the tool is not in use, keep the handles closed to prevent objects from becoming lodged in the crimping area. Store

the tool in a clean, dry area.

IN SERVICE TOOLS - AFTER TOOLS HAVE BEEN IN SERVICE:

It is recommended that each operator of the tool be made aware of - and responsible for following these maintenance

steps:

In-service tools should be cleaned and inspected at least ONCE A MONTH. To clean - wipe with a clean cloth.

In-service tools should be lubricated ONCE A WEEK, and after every cleaning. Lubricate all pins, pivots and bearing sur-

faces with DOW CORNING®Molykote BR2 Plus.

Be sure to clean any excess oil from the crimping dies before using.

®Molykote BR2 Plus is the Registered Trademark of DOW CORNING.

INSPECTION / MAINTENANCE

VISUAL INSPECTION

1. Visually inspect the tool for missing or loose pins; then close the tool and note the return action of the handles.

2. Inspect the crimping dies for worn, chipped or broken edges.

3. If parts are missing, defective or damaged; contact

PANDUIT

for information on repair or replacement of tools.

CT-1123 and CT-1104

OPERATION, INSPECTION and MAINTENANCE INSTRUCTIONS

Este manual sirve para los siguientes modelos

Otros manuales de Herramientas de crimpado de Panduit

Panduit

Panduit Blackfin CT-2980/TO Manual de usuario

Panduit

Panduit CT-1104 Manual de instrucciones

Panduit

Panduit CT-3001 Manual de usuario

Panduit

Panduit CT-1000 Guía del administrador

Panduit

Panduit CT-600-A Manual de usuario

Panduit

Panduit BlackFin CT-2600/LBT Manual de usuario

Panduit

Panduit CT-1002 Manual

Panduit

Panduit BlackFin CT-2931/STBT Manual de usuario

Panduit

Panduit PBTMT Manual de usuario

Panduit

Panduit BlackFin CT-2300/ST Manual de usuario

Panduit

Panduit Black Fin CT-2931/STCVUK Manual de usuario

Panduit

Panduit CT-930LPCH Manual de usuario

Panduit

Panduit Contour Crimp CT-1551 Manual de usuario

Panduit

Panduit CTFP-25 Manual de usuario

Panduit

Panduit BlackFin CT-2300 Series Manual de usuario

Panduit

Panduit CT-1003 Manual de instrucciones

Panduit

Panduit BlackFin CT-2600 Series Manual de usuario

Panduit

Panduit BlackFin CT-2920 Manual de usuario

Panduit

Panduit BlackFin CT-2980/STBT Manual de usuario

Panduit

Panduit Ezair CA9 Manual de usuario

Panduit

Panduit CT-2002CH Manual de usuario

Panduit

Panduit CT-2940/L Manual de usuario

Panduit

Panduit ClackFin CT-3001/CCPBT Manual de usuario

Panduit

Panduit CT-2500 Manual de usuario

Manuales populares de Herramientas de crimpado de otras marcas

JST

JST CS 10 Manual de usuario

molex

molex 63811-5100 Manual de usuario

Danfoss

Danfoss ET4200 Manual de usuario

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manual de usuario

TE Connectivity

TE Connectivity 2063528-1 Manual de usuario

molex

molex 63825-3000 Manual de usuario

Tyco Electronics

Tyco Electronics 69156-1 Manual de usuario

CRH

CRH CRL CBLHCT1 Manual de usuario

Emerson

Emerson Klauke ES 105CFM Manual de usuario

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Manual de instrucciones

Danfoss

Danfoss ET4350 Manual de usuario

Milwaukee

Milwaukee M18 Manual de usuario

HOGERT

HOGERT HT1P169 Manual de usuario

Textron

Textron ESG105L Manual de usuario

Tyco Electronics

Tyco Electronics 90035-3 Manual de usuario

Emerson

Emerson Klauke ES 20RMCCFB Manual de usuario

Continental Refrigerator

Continental Refrigerator PC150HD Manual de usuario

TE Connectivity

TE Connectivity ERGOCRIMP 1-1579001-3 Manual de usuario