Panduit ATLONA AT-HDR-CAT-2 Manual de usuario
1
Installation Guide
AT-HDR-CAT-2
4K/HDR
HDMI to HDBaseT™ 1x2 Distribution Amplier
AT-HDR-CAT-2
The Atlona AT-HDR-CAT-2 is a high dynamic range (HDR) distribution amplier with one HDMI®
input and two HDBaseT™ outputs Each output transmits 4K/UHD video @ 60 Hz with 4:4:4
chroma sampling plus support for HDR formats, multi-channel audio, control signals, and
power up to 130 feet (40 meters) or 1080p up to 230 feet (70 meters) over Category 6/6A cable.
The HDR-CAT-2 features sophisticated integration capabilities designed for commercial AV
distribution applications including HDMI pass-through, audio de-embedding, EDID management,
CEC display control, RS-232 and IR control extension, remote power for receivers, and HDBaseT
link testing. It oers compatibility with any TCP/IP or RS-232 control system and is housed in a
low-prole enclosure with external universal power supply. The HDR-CAT-2 is ideal for sending
HDR and 4K/60 4:4:4 content to AT-HDR-EX-70C-RX receivers.
IMPORTANT: Visit https://www.atlona.com/product/at-hdr-cat-2 for the latest rmware
updates and User Manual.
1 x AT-HDR-CAT-2
4 x 5-pin captive screw connectors
1 x 2-pin captive screw connector
1 x 48 V / 1.25 A power supply
1 x AC cord
1 x Pair rack mount ears
4 x Feet w/ rubber grips
Package Contents
2
Installation Guide
AT-HDR-CAT-2
1 HDMI Indicators
Displays the status of the HDMI IN and
HDMI OUT ports. When connected
to a source or display (sink) device,
respectively, the LED indicator will be
blue.
2 HDBaseT Indicators
Displays the status of the HDBaseT OUT
ports. When connected to an HDBaseT
receiver, with an active sink, the LED
indicator will be blue. If no active sink
is connected, or the sink is powered o,
then the indicator will not be illuminated.
3 Lock
This LED will be blue when the unit is
locked.
4 POWER
Press this button to power-on or place the
unit into standby mode.
5 INT
This LED indicator will be blue when the
unit is using an internal EDID.
6 LEARN
This LED indicator will ash when a
downstream EDID is being read into
memory.
7 EDID
Press this button to switch between the
internal (INT) and learned (LEARN) EDID
modes.
8 FW
Connect a USB Type-A to USB-C cable
from this port, to a computer, to update
the rmware. Refer to the AT-HDR-CAT-2
User Manual for more information.
Front Panel Descriptions
DC 48VLANHDMIAUDIO OUT IN OUT
IRRS-232
RX TX RXTX
MASTER
1 2
HDBaseT OUT
RX RXTX TX
RS-232 IR
RL 1
2
FWEDID
AT-HDR-CAT-2 POWER
INTLOCK21OUTIN
HDMI
LEARN
HDBaseT
123 4 5 6 7 8
3
Installation Guide
AT-HDR-CAT-2
DC 48VLAN
HDMIAUDIO OUT IN OUT
IRRS-232
RX TX RXTX
MASTER
1 2
HDBaseT OUT
RX RXTX TX
RS-232 IR
RL 1
2
FWEDID
AT-HDR-CAT-2 POWER
INTLOCK21OUTIN
HDMI
LEARN
HDBaseT
Rear Panel Descriptions
1 RS-232 / IR (MASTER)
Connect a control system or other DTE
device to this port to control the AT-HDR-
CAT-2.
2 AUDIO OUT
Connect the included 5-pin captive screw
connector to this port and connect it to an
audio amplifer, such as an AT-GAIN-60.
Refer to the AT-HDR-CAT-2 User Manual
for more information.
3 HDMI IN
Connect an HDMI cable from this port to a
source device.
4 HDMI OUT
Connect an HDMI cable from this port to
an HDMI input on a local display or an
additional AT-HDR-CAT-2 unit.
5 LAN
Connect an Ethernet cable from this port
to the network.
6 HDBaseT OUT
Connect Ethernet cables from these ports
to PoE-compatible receivers.
7 RS-232/IR 1 / 2
Connect a control system or other DTE
device to these ports for pass-through
zone control. Each of these ports uses
the associated HDBaseT OUT port. This
allows RS-232 command data to be sent
to a display (sink) device connected to a
PoE-comptible receiver.
8 DC 48V
Connect the included power supply to this
power receptacle.
61 23 4 5 87
4
Installation Guide
AT-HDR-CAT-2
POS
White
Black NEG
Power
1. Locate the included orange captive-screw block, and loosen the screws to allow room to
insert the copper wiring.
2. Wire the included power supply to the block, as shown below. Do not use high-torque
devices, when securing the wires to the captive-screw terminal block, as this may damage
the screws and/or block.
DC 48V
LANHDMIAUDIO OUT IN OUT
IRRS-232
RX TX RXTX
MASTER
1 2
HDBaseT OUT
RX RXTX TX
RS-232 IR
RL
1
2
FWEDID
AT-HDR-CAT-2 POWER
INTLOCK21OUTIN
HDMI
LEARN
HDBaseT
5
Installation Guide
AT-HDR-CAT-2
DC 48VLAN
HDMIAUDIO OUT IN OUT
IRRS-232
RX TX RXTX
MASTER
1 2
HDBaseT OUT
RX RXTX TX
RS-232 IR
RL 1
2
FWEDID
AT-HDR-CAT-2 POWER
INTLOCK21OUTIN
HDMI
LEARN
HDBaseT
Installation
Optional
1. Connect an HDMI cable from a source to the HDMI IN port.
2. Connect an HDMI cable from the HDMI OUT port to a local display.
3. Connect up to two Ethernet cables from the HDBaseT OUT ports to compatible PoE-
capable receivers. Refer to the table below for information on maximum cable length and
supported resolutions.
IMPORTANT: Stranded or patch cable is not recommended due to per-
formance issues. Sheilded cables are strongly recommended to minimize
signal noise and interference.
Cable 4K/UHD - Feet / Meters 1080p - Feet / Meters
HDMI 15 5 30 10
CAT5e/6 115 35 200 60
CAT6a/7 130 40 230 70
4. Connect an Ethernet cable from the LAN port to the Local Area Network (LAN). This step
will be required in order to access the built-in web server.
5. Connect the included power supply to the DC 48V connector and connect the power cord
to an available electrical outlet.
35 6 1 24 7
6. Connect an RS-232 or IR cable from the control system to the RS-232/IR ports. Refer to
the AT-HDR-CAT-2 User Manual for more information.
• MASTER RS-232/IR
Connecting to this port will provide direct control of the AT-HDR-CAT-2. Control can be
performed using either RS-232 or electrical IR.
• RS-232/IR 1 and RS-232/IR 2
Each of these ports is associated to the respective HDBaseT OUT port. This allows
RS-232 pass-through zone control of a display (sink) device that is connected to a
PoE-compatible receiver. Control can be performed using RS-232 or electrical IR.
7. Connect an audio output device to the AUDIO OUT port. Refer to the AT-HDR-CAT-2 User
Manual for more information.
6
Installation Guide
AT-HDR-CAT-2
The AT-HDR-CAT-2 is shipped with DHCP enabled. Once connected to a network, the DHCP
server (if available), will automatically assign an IP address to the unit. If the AT-HDR-CAT-2
is unable to detect a DHCP server within 15 seconds, then the unit will use a self-assigned IP
address within the range of 169.254.xxx.xxx/16. If this occurs, refer to the AT-HDR-CAT-2
User Manual for more information.
Use an IP scanner, along with the MAC address on the bottom of the unit, to identify the unit on
the network. If a static IP address is desired, the unit can be switched to static IP mode.
IP Conguration
Switching the IP mode using the Front Panel
1. Make sure the AT-HDR-CAT-2 is powered.
2. Connect an Ethernet cable between the LAN port of the AT-HDR-CAT-2 and the Local Area
Network (LAN).
3. Press and hold the POWER button for approximately 15 seconds. Release the POWER
button once all the front-panel LED indicators begin to ash. The number of ashes will
indicate the currently selected IP mode. Refer to the table, below.
DC 48VLANHDMIAUDIO OUT IN OUT
IRRS-232
RX TX RXTX
MASTER
1 2
HDBaseT OUT
RX RXTX TX
RS-232 IR
RL 1
2
FWEDID
AT-HDR-CAT-2 POWER
INTLOCK21OUTIN
HDMI
LEARN
HDBaseT
POWER button ashes Description
Two Static IP mode IP address: 192.168.1.254
Netmask: 255.255.0.0
Gateway: 192.168.1.1
Four DHCP mode
LOCK LED indicator
POWER button
Switching the IP mode can also be performed using commands or the built-in web server.
Refer the AT-HDR-CAT-2 User Manual for more information.
7
Installation Guide
AT-HDR-CAT-2
Accessing the built-in Web Server
The AT-HDR-CAT-2 includes a built-in web server, which allows easy management and control of
all features. Follow the instructions below to access the web server.
1. Make sure that an Ethernet cable is connected between the LAN port on the AT-HDR-CAT-2
and the network.
2. Launch a web browser and enter the IP address of the unit.
3. The AT-HDR-CAT-2 Register page will be displayed.
4. Create a username and password.
5. Click the Register button.
6. The Login page will be displayed.
7. Enter the username and password that was created during the registration process.
8. Click the Login button.
9. Refer to User Manual for more information on using the built-in web server.
8
Installation Guide
AT-HDR-CAT-2
Version 1 25306-R1
®
The terms HDMI, HDMI High-Denition Multimedia Interface, and the HDMI Logo are trademarks or
registered trademarks of HDMI licensing Administrator, Inc.
© 2023 Atlona Inc. All rights reserved. “Atlona” and the Atlona logo are registered trademarks of Atlona Inc. All other brand names and trademarks or registered
trademarks are the property of their respective owners. Pricing, specications and availability subject to change without notice. Actual products, product images, and
online product images may vary from images shown here.
English Declaration of Conformity
The English version can be found under the resources tab at:
https://atlona.com/product/at-hdr-cat-2/.
Warranty
Chinese Declaration of Conformity 中国RoHS合格声明
To view the product warranty, use the following link or QR code:
https://atlona.com/warranty/.
由SKU列出於:
https://atlona.com/about-us/china-rohs/.
US International
atlona.com •408.962.0515 •41.43.508.4321
Otros manuales para ATLONA AT-HDR-CAT-2
1
Tabla de contenidos
Otros manuales de Amplificador de Panduit
Panduit
Panduit Atlona UHD-CAT-4 Manual de usuario
Panduit
Panduit ATLONA AT-UHD-CAT-8 Manual de usuario
Panduit
Panduit ATLONA AT-HDR-CAT-2 Manual de usuario
Panduit
Panduit Atlona AT-UHD-CAT-4 Manual de usuario
Panduit
Panduit ATLONA AT-HDR-CAT-4ED Manual de usuario
Panduit
Panduit ATLONA AT-HDR-CAT-4 Manual de usuario
Panduit
Panduit ATLONA AT-HDR-CAT-4EDLA Manual de usuario
Panduit
Panduit ATLONA AT-UHD-CAT-8 Manual de usuario
Panduit
Panduit Atlona AT-UHD-CAT-4ED Manual de usuario
Panduit
Panduit ATLONA AT-HDR-CAT-8 Manual de usuario
