Panasonic MC-CG663 Manual de usuario
© 2006 Matsushita Electric Industrial Co., Ltd. All
rights reserved. Unauthorized copying and distribu-
tion is a violation of law.
Order No.VCB0605008CE
Vacuum Cleaner
MC-CG663/MC-CG663K
MC-CG661/MC-CG661K
Destination :Europe
2
1 Specifications
Model No. MC-CG663
MC-CG663K
MC-CG661
MC-CG661K
Power source AC230V~50Hz
AC230-240V~50Hz
AC230V~50Hz
AC230-240V~50Hz
Input power (MAX) 2000W 2000W
Input power (IEC) 1600W
1500-1600W
1600W
1500-1600W
Power control OO
Extension wand Metal telescopic Metal telescopic
Floor nozzle 2-Step OO
Turbin nozzle O-
Parquet nozzle - O
Dimensions (WxLxH)mm 280x430x260
Cord length 6.5m
Net weight 5.1kg
Cleaning tools Crevice nozzle / Dusting brush
3
2 Location of Controls and Components
4
5
3 Troubleshooting Guide
CONDITION CHECKPOINT METHOD OF INSPECTION CAUSE / REMEDY
Motor fails to rotate
(no noise is heard at all)
Power supply cord Check power supply cord continu-
ity.
If there is no continuity, replace the
cord reel patition unit.
Fuse
(Plug for UK only)
Check plug fuse continuity. If there is no continuity, replace the
cord reel patition unit.
Fuse of P.C.B. Ass’y
(250V, 12A)
Check fuse continuity. If there is no continuity, replace
P.C.B. Ass’y.
Motor continuity Check the conduction between the
terminals of the motor.
If there is no continuity, replace the
or motor.
ON/OFF Switch Check continuity across switch
connections
If there is no continuity, replace
P.C.B. Ass’y.
Triac (Inside of P.C.B.) Check if the triac is in open circuit. If it is in open circuit, replace
P.C.B.Ass’y.
P.C.B. Ass’y Check the internal parts for any-
thing unusual. (burn-out, melt-
down, etc.)
If anything is found unusual,
replace the P.C.B. assembly with
new one.
Motor runs but there is no suction Hose or Suction inlet Check if there is any blockage in
the hose or suction inlet.
If there is any blockage, remove it.
Dust bog / Secondary filter Check if dust bag is full or Second-
ary filter is choked up.
If dust bag is foll, replace with a
new one. If Secondary filter is
choked up, remove and clean it out
or replace.
Noise or vibration Motor fan Check dust accumulated in motor
fan (it could happen if the vacuum
cleaner has been used without cen-
tral filter).
If there is dust accumulated in the
motor fan, replace the motor and
check filter condition. (never try to
dismantle the motor fan)
Motor does not change power
(runs always at full speed)
Power control Adjust the power control and check
whether or not the resistance var-
ies. (Gray←→Blue)
If the resistance does not vary, then
replace the P.C.B. Ass'y.
P.C.B. Ass’y Examine the triac in the P.C.B.
Ass'y and check whether or not T1
and T2 are short-circuited.
If they are short-circuited, then
replace the P.C.B. Ass'y.
Motor runs irregularly P.C.B. Ass’y Check possible bad contact of
P.C.B. Ass’y.
Replace P.C.B. Ass’y.
6
4 Disassembly and Assembly Instructions
Important notice: Before replacing any components, make sure to turn OFF the vacuum cleaner.
Remove the power plug from the outlet.
4.1. Dust box cover assembly
removal
1. Open the dust box cover assembly at an angle of approx.
45°. Insert a flat-blade screwdriver between the upper
body and the dust box cover assembly and move it in the
direction of the arrow mark to remove the dust box cover
assembly from its right side.
4.2. Separate the upper and lower
body units
1. Remove the five screws fixing the upper body U and
lower body U.
2. Remove the screw fixing the upper body U from the rear
side.
7
3. Lift the upper body U to separate it from the lower body U.
4.3. Printed circuit board assembly
(P.C.B Ass’y) removal
1. Remove the Swivel cap unit and Insulation plate.
2.
3. Disengage the fast-on terminal of the wires (red) and
(blue) which lead to the cord reel partition wall connected
to the printed circuit board assembly.
4. Remove the P.C.B. Ass'y from the P.C.B. holder.
8
5. Remove the two screws fixing the P.C.B. holder and pull it
out from the lower body U.
* For removing the printed circuit board assembly,
first remove the fast-on terminal for the connecting
section for the motor.
4.4. Motor removal
1. Remove the dust box lid assembly. (Refer to paragraph
4.1 on P.6)
2. Remove the upper body from the lower body. (Refer to
paragraph 4.2 on P.6)
3. Remove the printed circuit board Ass’y. (P.C.B Ass’y)
(Refer to paragraph 4.3 on P.7)
4. Remove the two screws fixing the P.C.B. holder and pull it
out from the lower body U.
5. Lift the motor section from the lower body U.
9
6. Remove all components fitted to the motor.
a. Remove the motor support rubber (rear).
b. Remove the motor support.
c. Remove the noise suppressor.
d. Remove the motor support rubber (front).
e. Remove the lead wires connected to the motor.
4.5. Cord reel partition unit replace-
ment
1. Increase the gap width between the cord reel and the
lower body with a screwdriver. While removing the cord
reel shaft from the side of the lower body, lift the cord reel
partition unit.
* For easy removal, pull out the cord slightly, and
then lift the cord reel.
10
4.6. Rail base U replacement
1. Remove the screw fixing the rail base U onto the cord reel
partition U.
2. Remove the rail base U from the cord reel partition U.
4.7. Spring-loaded cord reel pre-
winding
1. The cord reel partition U has a spring that pre-winds the
cord reel.
If the cord is not wound, then press the brake arm, and
the cord pre-winding will be loosened.
If you wish to apply pre-winding again, then wind the cord
three turns in the direction of the arrow mark.
* If you wish to release the pre-winding, then make
sure to hold the cord plug.
4.8. How to disassemble the tur-
bine nozzle
(MC-CG663,CG663K)
4.8.1. Agitator ass'y
1. Rotate the brush cover to unlock it and remove the brush
cover U.
2. Pull up the rotating brush and remove the belt and rotat-
ing brush (complete). (Fig.19)
4.8.2. Separation of the floor nozzle upper
from the floor nozzle lower U
1. Remove the four screws fixing the floor nozzle lower U.
(Fig.20)
2. Remove the floor nozzle lower U.
Otros manuales para MC-CG663
1
Este manual sirve para los siguientes modelos
3
Tabla de contenidos
Otros manuales de Aspiradora de Panasonic
Panasonic
Panasonic MC-UL423-00 Manual de usuario
Panasonic
Panasonic MC-CG677-SC79 Manual de usuario
Panasonic
Panasonic QuickDraw MC-V7315 Manual de usuario
Panasonic
Panasonic MCCG885 - CANISTER VACUUM - MULTI LANGUAGE Manual de usuario
Panasonic
Panasonic MCV7365 - UPRIGHT VACUUM-QKDR Manual de usuario
Panasonic
Panasonic MC-YL637 Manual de usuario
Panasonic
Panasonic MC-CG381-AU21 Manual de usuario
Panasonic
Panasonic MC-UG323 Manual de usuario
Panasonic
Panasonic QuickDraw MC-V5355 Manual de usuario
Panasonic
Panasonic Ultra-Pro MC-V400 Manual de usuario
Panasonic
Panasonic Ultra-Pro MC-V300 Manual de usuario
Panasonic
Panasonic MC-CG683-ZC79 Manual de usuario
Panasonic
Panasonic MC-CG525 Manual de usuario
Panasonic
Panasonic MCV5744 - UPRIGHT VACUUM Manual de usuario
Panasonic
Panasonic MC-CL943 Manual de usuario
Panasonic
Panasonic MC-E4063K Manual de usuario
Panasonic
Panasonic MC-CG463-KA76 Manual de usuario
Panasonic
Panasonic MC-CL481 Manual de usuario
Panasonic
Panasonic MC-CG881C-SC79 Manual de usuario
Panasonic
Panasonic MCV5037 - UPRIGHT VACUUM Manual de usuario
